PadhaikoAll subjects

Guided transmission media: Co-axial cable, twisted pair, optical…

Data Communication (ENCT 253)

Open in the Padhaiko app

3.1 Guided Transmission Media: Twisted Pair, Coaxial Cable, and Optical Fiber

Guided transmission media confine electromagnetic energy inside a physical medium—copper wire or glass/plastic fiber—along a directed path from transmitter to receiver.

Twisted-Pair Cable

A twisted-pair cable consists of two insulated copper conductors twisted together in a helix. Because both wires experience nearly identical external electromagnetic interference (EMI), twisting causes induced noise voltages to cancel out at the differential receiver and reduces crosstalk between adjacent pairs.

Coaxial Cable

A coaxial cable uses a concentric cylindrical geometry: a central copper core, surrounded by a solid/foam dielectric insulator, enclosed by a metallic foil or braided outer conductor (shield), and covered by an outer protective jacket. The outer conductor shields the inner signal far better than UTP and acts as the return path.

Optical Fiber

Optical fiber transmits information as modulated pulses of light through an ultra-pure silica glass or plastic core rather than electrical current.

Definition

Total Internal Reflection and Fiber Parameters

An optical fiber consists of an inner core (refractive index ) surrounded by a cladding () and protective buffer/jacket. Light rays striking the core–cladding boundary at an angle greater than the critical angle undergo Total Internal Reflection (TIR) and remain trapped inside the core:

where is the Numerical Aperture and is the maximum half-acceptance angle for light entering the fiber from air ().

Comparison of Guided Transmission Media
ParameterTwisted Pair (UTP/STP)Coaxial CableOptical Fiber
Signal FormElectrical voltageElectrical voltageLight pulses (photons)
Typical BandwidthUp to (Cat 6a)Up to Tens of (optical windows)
Max Data Rate – – few – multi- (DWDM)
Repeater Spacing (Ethernet) (single-mode)
EMI ImmunityLow (UTP) to Moderate (STP)Moderate to HighComplete (immune to EMI)
Cost & InstallationLowest cost; easiest to terminateModerate cost and flexibilityHigher splicing/transceiver cost

3.2 Unguided Transmission Media: Radio Waves, Microwaves, and Infrared

Unguided (wireless) transmission media transport electromagnetic waves through air, atmosphere, or vacuum without a physical conductor. Propagation behavior depends strongly on frequency.

Comparison of Unguided Transmission Media
MediumFrequency RangeDirectionality & PathTypical Data RateKey Advantages & Disadvantages
Radio Waves – Omnidirectional; follows sky/ground paths; penetrates buildings – low Covers wide areas without dish alignment; prone to interference and limited bandwidth
Microwaves – Unidirectional (Line-of-Sight); focused by parabolic/horn antennasTens of – multi-High bandwidth, no right-of-way trenching; blocked by obstacles and attenuated by rain ()
Infrared – Strict Line-of-Sight; cannot penetrate solid walls – (FSO)Unlicensed spectrum and room-level isolation (security); short range and disrupted by bright sunlight

3.3 Antenna Basics, Satellite Communication, Bluetooth, and Wi-Fi

Antenna Basics

An antenna is an electrical transducer that converts guided Radio Frequency (RF) currents on a conductor into electromagnetic waves in free space (transmitting) or captures free-space EM waves back into guided RF currents (receiving) (DC Ch4).

Definition

Fundamental Antenna Properties

Common Antennas and Their Characteristics
Antenna TypeStructure & PrincipleTypical GainPrimary Use
Ground PlaneVertical quarter-wave radiator above angled radial ground elements ()Simple omnidirectional multipoint links
Yagi-UdaHalf-wave driven dipole + rear reflector (slightly longer) + front directors (slightly shorter)Point-to-point links ( horizontal beamwidth)
HornFlared rectangular, square, or conical waveguide openingStand-alone short link or active feed element for parabolic dishes
BiQuadTwo side squares mounted in front of a metallic reflector plate point-to-point ( beamwidth) or dish feeder
Sectorial & Panel/PatchPhased dipoles with back reflector (sectorial) or flat solid patch arrayUp to Cellular towers (sectorial) and indoor wall coverage (patch)
Parabolic DishParabolic reflector converts spherical waves at focus into a collimated plane waveVery high ()Long-haul microwave backhaul and satellite earth stations

For a parabolic dish of diameter , central depth , and illumination efficiency (typically ), the focal length, linear power gain, and half-power beamwidth are (DC Ch4):

Doubling the dish diameter quadruples the gain ().

Satellite Communication

A communication satellite acts as an orbital microwave repeater equipped with transponders that receive weak uplink signals, shift their frequency (to prevent transmit-to-receive self-interference), amplify them, and beam them back on a downlink frequency. Common bands include C-band (, rain-resistant), Ku-band (, DTH TV & VSAT), and Ka-band (, high-throughput broadband).

Satellite Orbital Regimes
Orbit TypeAltitudeOrbital PeriodOne-Way Delay (approx.)Key Characteristics & Applications
GEO (Geostationary) (stationary above equator) ( single-hop RTT)Three satellites cover almost the entire Earth (except poles); fixed ground dishes; weather & broadcast TV
MEO (Medium Earth)Moderate latency and constellation size; used for navigation (GPS at )
LEO (Low Earth)Low latency and small user terminals, but requires large constellations and frequent handoffs (Starlink, Iridium)
AspectOptical FiberSatellite Transmission
Frequency & BandwidthTens of (optical spectrum); massive capacity microwave bands (C, Ku, Ka); narrower shared bandwidth
Security & InterferenceExtremely secure, immune to EMI and weatherBroadcast footprint is interceptable; Ku/Ka suffer rain fade
Flexibility & CoverageFixed point-to-point trenches; costly across oceans/mountainsInstant wide-area / mobile / remote coverage without cabling
LatencyLow ()High in GEO ( one-way earth–sat–earth); low in LEO

Bluetooth (IEEE 802.15.1)

Bluetooth is a short-range Wireless Personal Area Network (WPAN) operating in the unlicensed ISM band ().

Wi-Fi (IEEE 802.11 WLAN)

Wi-Fi implements wireless local area networking under the IEEE 802.11 family:

Major IEEE 802.11 Wi-Fi Standards
StandardMarketing NameBand(s)Max Nominal RateKey Physical Enhancement
802.11bWi-Fi 1DSSS / CCK
802.11aWi-Fi 2OFDM (, shorter range)
802.11gWi-Fi 3OFDM brought to
802.11nWi-Fi 4 & MIMO (), channels
802.11acWi-Fi 5MU-MIMO, , -QAM
802.11axWi-Fi 6 / 6EOFDMA, -QAM, dense multi-user efficiency

Worked Examples

Example 1

1

A step-index optical fiber has a glass core refractive index and cladding refractive index . Calculate:

  1. The critical angle at the core–cladding interface.
  2. The numerical aperture () and maximum acceptance angle in air ().

1. Critical angle :

2. Numerical aperture and acceptance angle:

Answer:
  1. , acceptance half-angle
Example 2

2

A parabolic dish antenna of diameter and efficiency operates on a Wi-Fi point-to-point link (). Find:

  1. The signal wavelength .
  2. The antenna power gain (linear and in ).
  3. The half-power beamwidth in degrees.

1. Wavelength at :

2. Power gain (linear and ):

3. Half-power beamwidth:

Answer:
  1. ()
Example 3

3

A GEO satellite orbits at an altitude of directly above an earth station and relays a link to another station (assume signal speed and ignore slant-range angle correction).

  1. Calculate the one-way earth–satellite–earth propagation delay.
  2. How many megabits are in flight on this one-way satellite hop (the bandwidth–delay product)?

1. One-way earth–satellite–earth propagation delay: The signal travels twice the orbital altitude (uplink downlink), a total distance of :

2. Bandwidth–delay product (bits in transit):

Answer:
  1. One-way propagation delay .
  2. Bandwidth–delay product .

Exercises

Exercises

Question 1

Why are the wire pairs in twisted-pair cables twisted together? Differentiate between UTP and STP, and state two applications of each.

Purpose of twisting: Twisting keeps both conductors at virtually the same average distance from external EMI sources and adjacent pairs, so induced noise affects both wires nearly equally and cancels at the differential receiver, minimizing crosstalk.

UTP vs. STP:

  • UTP (Unshielded Twisted Pair): Contains no metallic shield around pairs; lightweight, inexpensive, flexible, easy to terminate (RJ-45). Used in office Ethernet LANs (Cat 5e/6) and telephone subscriber lines.
  • STP (Shielded Twisted Pair): Surrounds each pair and/or cable core with braided or foil shielding to block strong external EMI; costlier and requires grounding. Used in factory floors/industrial automation and high-EMI server rooms ( runs).
Answer:

Twisting cancels external EMI and reduces crosstalk; UTP is unshielded and economical for standard LANs/telephony, whereas STP adds metallic shielding for high-EMI industrial and data-center environments.

Question 2

What are the advantages of optical fiber over coaxial cable and twisted-pair cable? A step-index fiber has and ; find its critical angle and numerical aperture.

Advantages of optical fiber over copper media:

  1. Far higher bandwidth & data rate: Supports optical windows and – rates.
  2. Much lower attenuation: allows repeater spacing instead of (UTP) or (coax).
  3. Complete EMI immunity & no crosstalk: Photons are unaffected by lightning, motors, or nearby cables.
  4. Lighter weight & higher security: Thin glass strands are hard to tap without detectable light loss.

Critical angle and numerical aperture:

Answer:

Optical fiber offers vastly greater bandwidth, longer repeater spacing, lighter weight, and total EMI immunity; and .

Question 3

Compare radio waves, microwaves, and infrared as unguided transmission media with respect to frequency range, propagation directionality, obstacle penetration, and typical applications.

Comparison across the three unguided media:

  • Radio Waves (–): Omnidirectional; penetrates walls and follows ground/sky paths; suited for AM/FM broadcast and wide-area mobile coverage.
  • Microwaves (): Unidirectional line-of-sight using focused antennas; blocked by terrain/buildings and attenuated by heavy rain (); suited for terrestrial towers, cellular backhaul, Wi-Fi, and satellite links.
  • Infrared (–): Strict short-range line-of-sight; cannot pass through solid walls (giving inherent room privacy and no licensing); suited for remote controls and indoor IrDA.
Answer:

Radio waves (–) are omnidirectional and wall-penetrating; microwaves () are high-bandwidth unidirectional line-of-sight links; infrared (–) is short-range, wall-blocked line-of-sight.

Question 4

Explain antenna reciprocity and distinguish among omnidirectional, sectorial, and directive antennas. A parabolic dish of diameter operates at : compute its half-power beamwidth and explain how doubling from to changes its gain in .

Reciprocity and directivity classes:

  • Reciprocity means an antenna's gain, radiation pattern, and impedance remain identical whether transmitting or receiving.
  • Omnidirectional antennas radiate horizontally (e.g., dipole, ground plane); sectorial antennas focus into a sector (cellular towers); directive antennas focus into a narrow beam for long point-to-point links (Yagi, horn, parabolic dish).

Beamwidth at and effect of doubling diameter:

Since , doubling from to multiplies linear gain by , an increase of .

Answer:

Reciprocity guarantees identical Tx/Rx patterns; antennas are omnidirectional, sectorial, or directive. At with , , and doubling increases gain by ().

Question 5

Compare Optical Fiber and Satellite Transmission across bandwidth, security, flexibility, interference, latency, and connectivity.

Point-by-point comparison:

  • Bandwidth: Optical fiber provides tens of (multi- per fiber); satellite links are constrained to RF bands shared by many users.
  • Security: Fiber is physically confined and hard to tap stealthily; satellite downlinks broadcast across wide footprints and require strong encryption.
  • Flexibility & Connectivity: Fiber requires fixed physical trenching/conduits; satellites rapidly connect remote regions, ships, aircraft, and broadcast receivers anywhere in footprint.
  • Interference: Fiber is immune to EMI and rain; satellite Ku/Ka signals suffer atmospheric rain fade and solar interference.
  • Latency: Fiber delay is low (); GEO satellites incur single-hop delay (while LEO lowers this to RTT).
Answer:

Optical fiber excels in bandwidth, low latency, and EMI/security isolation on fixed routes, whereas satellite transmission offers instant wide-area and mobile connectivity at higher GEO latency and weather susceptibility.

Question 6

Explain the architecture and medium-access mechanism of Wi-Fi (IEEE 802.11) and Bluetooth (IEEE 802.15.1), highlighting CSMA/CA and FHSS Piconets.

Wi-Fi (IEEE 802.11): Stations associate with an Access Point (AP) to form a BSS (or multiple BSSs form an ESS for roaming). Because wireless nodes cannot simultaneously detect collisions while transmitting, Wi-Fi uses CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance): stations sense the medium, wait a random backoff, verify delivery via explicit ACKs, and optionally exchange RTS/CTS frames to mitigate hidden terminals.

Bluetooth (IEEE 802.15.1): Operates in the ISM band using FHSS ( channels hopping times/s in Classic BR/EDR) to avoid narrowband interference. Up to master and active slaves share a synchronized hopping clock inside a Piconet, and interconnected piconets form a Scatternet.

Answer:

Wi-Fi forms AP-based BSS/ESS WLANs using CSMA/CA (with optional RTS/CTS) for collision avoidance, whereas Bluetooth forms short-range master/slave Piconets and Scatternets using FHSS (plus BLE for low-power IoT).

Past exam questions for Data Communication

← Data Communication FundamentalsWireless propagation (Introduction to groundwave propagation, sky… →