Basic Circuits Concepts
Open in the Padhaiko app1.1 Current and potential
All electrical and electronic circuit analysis rests on two fundamental quantities: electric current (the flow rate of charge) and electric potential (the energy per unit charge).
Electric Charge, Current, Potential, Power, and Energy
- Electric Charge (): A fundamental conserved property of matter, measured in coulombs (). One electron carries a charge of .
- Electric Current ( or ): The time rate of flow of net electric charge through a cross-sectional area of a conductor, measured in amperes (), where :
- Direct Current (DC): Current whose magnitude and direction remain constant over time ().
- Alternating Current (AC): Current that reverses its direction periodically with time (for example, ).
- By universal circuit convention, conventional current is drawn in the direction of positive charge flow (opposite to electron motion in metallic conductors).
- Electric Potential and Potential Difference (Voltage, or ): The work done (or energy transferred) per unit positive charge in moving a test charge from point to point , measured in volts (), where :
Point is at a higher potential than when (indicated by at and at ).
- Electric Power ( or ) and Energy ( or ): Power is the time rate of absorbing or supplying energy, measured in watts () (), and energy is measured in joules ():
1.2 Passive components: Resistance, inductance, capacitance; Series, parallel combinations; Kirchhoff’s voltage and current laws for DC circuits
Passive Circuit Elements (, , and )
A passive element cannot generate net energy over all time; it either dissipates energy (resistor) or stores and returns it in an electromagnetic field (inductor and capacitor).
Resistance, Inductance, and Capacitance
- Resistance (, Ohm ): Opposes the flow of electric current and dissipates electrical energy as heat.
- Ohm's Law: At constant temperature, the voltage across an ideal linear resistor is directly proportional to the current through it:
where is conductance in siemens (). For a uniform conductor of resistivity , length , and cross-sectional area , .
- Power dissipated: .
- Inductance (, Henry ): Opposes sudden changes in current by storing energy in a magnetic field.
- Voltage–current relation:
- Stored magnetic energy: .
- DC steady-state behavior: When current is constant (), ; an ideal inductor acts as a short circuit to steady DC.
- Capacitance (, Farad ): Opposes sudden changes in voltage by storing energy in an electric field between two conducting plates ().
- Current–voltage relation:
- Stored electrostatic energy: .
- DC steady-state behavior: When voltage is constant (), ; an ideal capacitor acts as an open circuit to steady DC.
| Quantity | Resistor () | Inductor () | Capacitor () |
|---|---|---|---|
| SI Unit | Ohm () | Henry () | Farad () |
| V–I Relation | |||
| Energy Storage / Loss | Dissipates as heat | Stores | Stores |
| Continuity Variable | None (instantaneous) | Inductor current cannot jump | Capacitor voltage cannot jump |
| DC Steady-State Model | Resistance | Short circuit () | Open circuit () |
Series and Parallel Combinations and Divider Rules
Elements in series carry the same current, while elements in parallel share the same voltage. Notice that inductors combine just like resistors, whereas capacitors follow the dual rule (series adds reciprocals; parallel adds directly).
| Element | Series Equivalent ( elements) | Parallel Equivalent ( elements) | Two-Element Parallel Shortcut |
|---|---|---|---|
| Resistors | |||
| Inductors (no mutual coupling) | |||
| Capacitors | (series!) |
- Voltage Divider Rule (Series Resistors): When total voltage is applied across series resistors , the voltage across is:
- Current Divider Rule (Two Parallel Resistors): When total current enters two parallel resistors and :
(Note the opposite resistor in the numerator: more current flows through the smaller resistance.)
Kirchhoff’s Voltage and Current Laws for DC Circuits
Kirchhoff's Current Law (KCL) and Kirchhoff's Voltage Law (KVL)
- Kirchhoff's Current Law (KCL — Conservation of Charge): The algebraic sum of all currents entering (or leaving) any node or closed surface in a lumped circuit is zero at every instant:
- Kirchhoff's Voltage Law (KVL — Conservation of Energy): The algebraic sum of all branch voltages around any closed path (loop or mesh) in a circuit is zero:
1.3 Signal sources: Voltage and current sources; Non ideal sources; Representation under assumption of linearity; Controlled sources: VCVS, CCVS, VCCS, CCCS; Concept of gain, transconductance, transimpedance
Voltage and Current Sources and Non-Ideal Sources
- Ideal Independent Voltage Source: Maintains a specified terminal voltage regardless of the current drawn by the load. Its internal series resistance is . (It must never be short-circuited.)
- Ideal Independent Current Source: Delivers a specified current regardless of the voltage across its terminals. Its internal parallel resistance is . (It must never be left open-circuited.)
- Non-Ideal (Practical) Sources & Representation under Linearity: Real batteries, signal generators, and transducers exhibit internal voltage drop or leakage as load current changes. Assuming linearity, a practical source is modeled using an ideal source combined with a constant linear internal resistance:
- Practical Voltage Source: An ideal voltage source in series with internal resistance . With load resistance , the terminal voltage obeys the linear relation:
- Practical Current Source: An ideal current source in parallel with internal resistance . With load , the load current obeys:
| Feature | Ideal Voltage Source | Practical Voltage Source | Ideal Current Source | Practical Current Source |
|---|---|---|---|---|
| Circuit Model | Ideal alone | Ideal in series with | Ideal alone | Ideal in parallel with |
| Internal Resistance | Finite | Finite | ||
| Terminal Equation | (constant) | (constant) | ||
| Source Transformation | Cannot convert to current source | Equivalent to in parallel with | Cannot convert to voltage source | Equivalent to in series with |
Controlled (Dependent) Sources: VCVS, CCVS, VCCS, CCCS
A controlled (dependent) source is an active source whose output voltage or current is proportional to a controlling voltage or current elsewhere in the circuit. They are essential for modeling transistors (BJT/FET) and operational amplifiers.
| Acronym | Full Name | Output Relation | Controlling Variable | Scaling Parameter & SI Unit | Typical Electronic Model |
|---|---|---|---|---|---|
| VCVS | Voltage-Controlled Voltage Source | Voltage | Voltage gain or (dimensionless, ) | Op-amp voltage amplifier | |
| CCVS | Current-Controlled Voltage Source | Current | Transresistance / transimpedance () | Transimpedance amplifier | |
| VCCS | Voltage-Controlled Current Source | Voltage | Transconductance ( or ) | MOSFET / BJT hybrid- model | |
| CCCS | Current-Controlled Current Source | Current | Current gain or (dimensionless, ) | BJT collector current |
Concept of Gain, Transconductance, and Transimpedance
Gain, Transconductance, and Transimpedance
- Voltage Gain ( or ): Ratio of output voltage to input controlling voltage:
- Current Gain ( or ): Ratio of output current to input controlling current:
- Transconductance (): Ratio of output current to input controlling voltage ("transfer conductance"):
- Transimpedance / Transresistance ( or ): Ratio of output voltage to input controlling current ("transfer resistance/impedance"):
1.4 Maximum power transfer, superposition theorem, Thevenin’s theorem, Norton’s theorem
Circuit theorems simplify complex linear bilateral networks containing multiple sources and resistors.
Superposition Theorem
In any linear bilateral network containing two or more independent sources, the voltage across (or current through) any element equals the algebraic sum of the voltages (or currents) produced by each independent source acting alone, with all other independent sources deactivated:
- Replace every deactivated independent voltage source with a short circuit ().
- Replace every deactivated independent current source with an open circuit ().
- Keep all dependent (controlled) sources active in every sub-circuit.
Caution: Superposition applies only to linear responses ( and ). It does not apply directly to power ( is nonlinear); find total or first, then compute .
Thevenin's Theorem
Any linear bilateral two-terminal DC network can be replaced at terminals – by a single independent voltage source in series with a single equivalent resistance :
- (Thevenin Voltage): The open-circuit voltage across terminals – with the load disconnected.
- (Thevenin Resistance):
- Case 1 (Independent sources only): Deactivate all independent sources (short voltage sources, open current sources) and compute the equivalent resistance seen looking into terminals –.
- Case 2 (With dependent sources): Keep dependent sources active, deactivate independent sources, apply a test voltage (or current ) across –, and calculate (alternatively, when ).
Norton's Theorem
Any linear bilateral two-terminal DC network can be replaced at terminals – by a single independent current source in parallel with a single equivalent resistance :
- (Norton Current): The short-circuit current flowing from terminal to when terminals – are connected together by an ideal short circuit.
- (Norton Resistance): Identical to the Thevenin resistance ().
By source transformation, Thevenin and Norton equivalents satisfy:
Maximum Power Transfer Theorem (DC)
A resistive load connected to a linear DC network (modeled by its Thevenin equivalent in series with ) absorbs maximum power when the load resistance equals the Thevenin resistance of the source network:
At this matched condition:
- Load current: , load voltage: .
- Maximum power delivered to :
- Power transfer efficiency: Exactly , because an equal amount of power is dissipated inside .
Worked Out Examples
1.1
In a DC circuit, node is connected to ground through three branches:
- Branch 1: an ideal voltage source (positive at top) in series with .
- Branch 2: a resistor directly to ground.
- Branch 3: a ideal voltage source (positive at top) in series with .
Using Kirchhoff's laws, find the node voltage , the current in each branch, and the power dissipated in .
Setting up KCL at node : Let be the potential of node with respect to the ground reference (). Applying KCL (sum of currents leaving node equals zero):
Solving for : Multiply every term by :
Computing branch currents and power in :
- Current supplied by the source into node :
- Current flowing downward through :
- Current flowing downward into the source branch:
(KCL check: .)
- Power dissipated in :
; branch currents are (into node ), (downward through ), and (into the branch); power dissipated in is .
1.2
A DC network has two independent sources: a voltage source in series with connected to node ; a resistor from node to ground; a resistor connecting node to node ; and at node , a resistor to ground in parallel with an upward current source (entering node ). Using the Superposition Theorem, find the total downward current through .
Contribution of alone ( open-circuited): With replaced by an open circuit, and are in series (). This branch is in parallel with :
Total current from :
By the current divider rule, the downward current in is:
Contribution of alone ( short-circuited): With replaced by a short circuit, and are in parallel:
Looking left from node , the resistance is , in parallel with .
Superposing both responses: Since both partial currents flow downward through :
The total downward current through is .
1.3
A DC source is connected to node via . From node , resistor goes to ground (terminal ), and resistor goes to output terminal . A variable load resistor is connected across terminals –. Find:
- The Thevenin equivalent () and Norton equivalent () seen by .
- The value of for maximum power transfer and the maximum power .
Finding (open-circuit voltage across –): With removed, zero current flows through , so . By the voltage divider rule across and :
Finding and Norton equivalent: Deactivate the voltage source by replacing it with a short circuit. Looking into terminals –, and are in parallel, in series with :
The Norton short-circuit current is:
Maximum power transfer condition and : For maximum power transfer to the load:
The maximum power delivered to is:
- Thevenin equivalent: , . Norton equivalent: , .
- Maximum power transfer occurs at , yielding .
Exercises
Practice Exercises — Basic Circuits Concepts
Distinguish between ideal and non-ideal (practical) voltage and current sources under the assumption of linearity. List all four types of controlled sources and define gain, transconductance, and transimpedance with their SI units.
Ideal vs. Non-Ideal Sources:
- An ideal voltage source maintains constant terminal voltage for any load current (), whereas a non-ideal (practical) voltage source has a linear internal series resistance , so its terminal voltage drops linearly with load current: .
- An ideal current source supplies constant current for any terminal voltage (), whereas a non-ideal (practical) current source has a linear internal parallel resistance , so load current decreases as terminal voltage rises: .
Four Controlled Sources and Transfer Parameters:
- VCVS (): dimensionless voltage gain ().
- CCCS (): dimensionless current gain ().
- VCCS (): transconductance , measured in siemens ().
- CCVS (): transimpedance (transresistance) , measured in ohms ().
Ideal sources have zero series resistance (voltage) or infinite parallel resistance (current), whereas linear practical sources include finite or . The four controlled sources are VCVS (, dimensionless), CCCS (, dimensionless), VCCS ( in ), and CCVS ( in ).
In a DC circuit at steady state, a battery is connected in series with a resistor and a parallel combination of and . An ideal inductor is in series with , and a capacitor network consisting of in series with , the pair placed in parallel with , is connected across . Calculate:
- The total equivalent resistance and steady-state battery current .
- The equivalent capacitance across .
- The steady-state energy stored in the inductor () and in the capacitor network ().
Steady-state DC equivalent and : At DC steady state, the ideal inductor acts as a short circuit () and the capacitors act as open circuits (). Thus all battery current flows through and :
The steady-state current through the battery and inductor is:
Equivalent capacitance and voltage across : and are in series:
This series pair is in parallel with :
The steady-state voltage across (and across ) is:
Stored energy in and :
- , .
- .
- , ().
A single-loop circuit contains a independent voltage source in series with , , and a current-controlled voltage source (CCVS) of value , where and is the clockwise loop current (polarity opposes the source). The output voltage is taken across the series combination of and the CCVS. Find , , and the voltage gain .
Applying KVL around the loop: Tracing clockwise from the source (rise) across , , and the opposing CCVS (drops):
Finding and the voltage gain : The output voltage across the series combination of and is:
The voltage gain is:
, , and .
In a two-source DC circuit, a voltage source (positive at top) in series with connects to node . From node to ground is a resistor , and also connected to node is a current source directed downward (leaving node toward ground). Using the Superposition Theorem, find the downward current through .
Response due to the voltage source ( current source opened): With the current source open-circuited, and are in series across :
Response due to the current source ( voltage source shorted): With the voltage source shorted, and are in parallel. The downward current pulls current upward from ground through and equally:
Combining both contributions:
The negative sign indicates that flows upward through (from ground to node ).
downward (or upward through ).
A linear network consists of a voltage source in series with connected to node , a downward current source from node to ground, and a resistor connecting node to terminal (terminal is ground). Find:
- The Thevenin and Norton equivalents across terminals –.
- The load resistance that draws maximum power across –, and the value of .
Finding (open-circuit at –): With – open, no current flows through , so . By KCL at node , the downward current must come entirely from the source through :
(Alternatively, transforming the source in series with to in parallel with , then subtracting gives in parallel with , which transforms back to in series with .)
Finding and : Deactivating independent sources ( short, open), looking into – sees in series with :
Thus, the Norton current is:
Maximum Power Transfer: Maximum power is transferred when :
- Thevenin equivalent: , . Norton equivalent: , .
- and .