Past exam question: 2082 Kartik (Back), Q2
Open in the Padhaiko appQuestion
Draw the internal architecture of 8085 microprocessor and explain briefly about its major components.
Solution
Architectural Overview & Internal Layout: The Intel 8085 is an 8-bit, NMOS microprocessor operating on a single +5V supply with a 3 MHz internal operating frequency. Its architecture comprises 7 functional sections connected via an 8-bit internal data bus:
+-----------------------------------------------------------------------------+
| INTEL 8085 INTERNAL ARCHITECTURE |
| |
| +----------------+ +----------------+ +-----------------------------------+ |
| | Interrupt Ctrl | | Serial I/O | | Register Array | |
| | TRAP, RST 7.5, | | SID, SOD | | B (8) | C (8) | |
| | 6.5, 5.5, INTR | +----------------+ | D (8) | E (8) | |
| +----------------+ | H (8) | L (8) | |
| | Stack Pointer (SP) (16) | |
| +-----------------------------------+ | Program Counter (PC) (16) | |
| | ALU Section | | Incrementer / Decrementer (16) | |
| | Accumulator (A) (8) | +-----------------+-----------------+ |
| | Temporary Register (8) | | |
| | Flag Register (8: S,Z,AC,P,CY) | v |
| | 8-bit ALU | +-------------------+ |
| +-----------------+-----------------+ | Address Buffer | |
| | | (A15–A8) | |
| v +---------+---------+ |
| ============================= | |
| 8-Bit Internal Data Bus v |
| ============================= A15–A8 Lines |
| | |
| v +-------------------+ |
| +-----------------------+ | Multiplexed | |
| | Instruction Register | | Address/Data Buf | |
| +-----------+-----------+ | (AD7–AD0) | |
| v +---------+---------+ |
| | Instruction Decoder | | |
| +-----------+-----------+ v |
| v AD7–AD0 Lines |
| | Timing & Control Unit | |
| | CLK, ALE, RD, WR, | |
| | IO/M, S1, S0, READY | |
| +-----------------------+ |
+-----------------------------------------------------------------------------+Detailed Explanation of Major Components:
- Arithmetic and Logic Unit (ALU):
- 8-bit computational block performing arithmetic (add, subtract) and logic (AND, OR, XOR, NOT, rotate).
- Accumulator (Register A): 8-bit working register that holds one operand and receives the result of ALU operations.
- Temporary Register: Latches the second operand for the ALU during execution.
- Flag Register: 8-bit status register containing 5 active flip-flops: Sign (S), Zero (Z), Auxiliary Carry (AC), Parity (P), and Carry (CY).
- General Purpose Register Array:
- Six 8-bit registers:
B, C, D, E, H, L. - Can be used individually as 8-bit registers or combined as 16-bit register pairs:
BC, DE, HL. - The
HLpair functions as the primary 16-bit memory pointerM.
- Six 8-bit registers:
- Special Purpose Registers:
- Program Counter (PC): 16-bit register holding the memory address of the next instruction byte to be fetched. Automatically incremented after each fetch.
- Stack Pointer (SP): 16-bit register pointing to the top memory address of the LIFO stack in RAM.
- Temporary Registers W and Z: 8-bit registers invisible to the programmer, used internally by the CPU to hold operands during multi-byte instruction execution.
- Instruction Register & Decoder:
- Instruction Register (IR): Latches the 8-bit opcode fetched from memory during the opcode fetch cycle.
- Instruction Decoder: Translates the opcode into control signals sent to the timing and control unit.
- Timing and Control Unit:
- Derives internal clock phases and orchestrates system bus activity.
- Status & Control signals:
ALE(Address Latch Enable),RD_bar(Read),WR_bar(Write),IO/M_bar(Memory or I/O selection),S1, S0(bus state identifiers). - Synchronization & Reset:
READY,RESET IN_bar,RESET OUT,CLK OUT.
- Interrupt Control Unit:
- Evaluates hardware interrupt lines in decreasing priority:
TRAP,RST 7.5,RST 6.5,RST 5.5, andINTR. - Generates acknowledge signal
INTA_barfor INTR requests.
- Evaluates hardware interrupt lines in decreasing priority:
- Serial I/O Control:
- Provides software-controlled serial data transfer via
SID(Serial Input Data) andSOD(Serial Output Data) pins, inspected and updated viaRIMandSIMinstructions.
- Provides software-controlled serial data transfer via
- Address and Data Buffers:
- Address Buffer (A15–A8): Unidirectional tri-state buffer driving high-order address lines.
- Address/Data Buffer (AD7–AD0): Bidirectional multiplexed buffer carrying low-order address during T1 and 8-bit data during T2–T3.
Answer:
The 8085 internal architecture comprises 7 primary sections: ALU and Accumulator/Flags, General/Special Register array (B,C,D,E,H,L, PC, SP), Instruction Register and Decoder, Timing & Control Unit, Interrupt Control, Serial I/O, and Address/Data Buffers.