Transistor (part 2: 5.4–5.6)
Open in the Padhaiko app5.4 BJT as switch and logic circuits
When operated strictly between cutoff (open switch) and saturation (closed switch)—skipping the linear active region as fast as possible—a BJT functions as an electronic digital switch and basic logic element.
Cutoff and Saturation Switching States (NPN BJT)
Consider a common-emitter NPN switching transistor with collector resistor connected to and base resistor driven by input :
- OFF State (Cutoff — Switch Open / Logic HIGH Output):
- Condition: ( for Si; typically ).
- Both and junctions are reverse-biased, so and .
- Output voltage: .
- ON State (Saturation — Switch Closed / Logic LOW Output):
- Collector saturation current:
- Minimum base current to reach the edge of saturation: .
- Hard Saturation Condition (Overdrive Factor ): To guarantee deep saturation across temperature and spreads, design with , giving:
- Output voltage: .
- Switching Speed Limitations: A BJT switch is slowed by junction capacitance and minority-carrier charge stored in the base during saturation. Total turn-on time is (delay + rise time), and turn-off time is (storage time + fall time ), where dominates unless prevented (e.g., Schottky-clamped TTL).
BJT Logic Families (RTL, DTL, and TTL)
- RTL (Resistor–Transistor Logic):
- NOT gate (Inverter): Single CE transistor switch; saturates the BJT (); cuts it off ().
- NOR gate: Two or more BJTs connected in parallel sharing a common collector resistor ; if any input is HIGH, its transistor saturates and pulls LOW ().
- DTL (Diode–Transistor Logic):
- Uses input steering diodes for an AND stage followed by a BJT CE inverter to form a NAND gate (). Improved noise margin over RTL.
- TTL (Transistor–Transistor Logic):
- Replaces DTL input diodes with a multi-emitter NPN input transistor () for faster turn-off, paired with a phase-splitter () and an active totem-pole output stage () that provides low output impedance in both HIGH and LOW states. Standard TTL () operates at with propagation delay .
5.5 Construction and working principle of JFET, MOSFET and CMOS
Unlike BJTs (bipolar, current-controlled devices using both electrons and holes), Field-Effect Transistors (FETs) are unipolar, voltage-controlled devices in which an electric field modulates the conductivity of a semiconductor channel carrying only majority carriers. Their gate draws virtually zero DC current, yielding extremely high input impedance.
Junction Field-Effect Transistor (JFET)
- Construction (-channel JFET): A bar of -type silicon with Source () and Drain () ohmic contacts at opposite ends, and two heavily doped regions diffused into the sides and tied together to form the Gate (). (A -channel JFET reverses the doping types.)
- Working Principle: In normal operation, the gate–source junction is always reverse-biased ( for -channel). Increasing reverse bias widens the insulating depletion layers into the channel, narrowing the conductive path and reducing drain current . At the pinch-off / cutoff voltage (), the depletion layers meet and .
- Shockley Transfer Equation (Saturation / Pinch-Off Region, ):
where is the drain-to-source saturation current at .
Metal–Oxide–Semiconductor FET (MOSFET)
In a MOSFET, a thin insulating layer of silicon dioxide () separates the metal/polysilicon Gate () from the semiconductor Substrate / Body (), resulting in an input resistance of ().
- Depletion-Type MOSFET (D-MOSFET): Built with a physical conducting channel between and ; works with negative (depletion mode, reducing ) or positive (enhancement mode, increasing above ).
- Enhancement-Type MOSFET (E-MOSFET): Has no physical channel at . For an -channel E-MOSFET (NMOS) on a -type substrate, applying (threshold voltage) repels holes and attracts electrons to the interface, inducing an -type inversion channel between heavily doped source and drain regions.
- Cutoff Region (): No inversion channel exists; .
- Triode / Ohmic Region ( and ): Channel behaves as a voltage-controlled resistor:
- Saturation Region ( and ): Channel pinches off at the drain end and saturates:
(For a -channel E-MOSFET (PMOS) in an -well, reverse all voltage polarities: , conducts when or .)
| Parameter | BJT (NPN / PNP) | JFET (-ch / -ch) | E-MOSFET (NMOS / PMOS) |
|---|---|---|---|
| Control Mechanism | Current-controlled () | Voltage-controlled () | Voltage-controlled () |
| Carriers | Bipolar (electrons + holes) | Unipolar (majority carriers only) | Unipolar (majority carriers only) |
| Gate / Base Isolation | Forward-biased junction | Reverse-biased junction | Insulated dielectric |
| Input Impedance | Low to moderate () | High () | Extremely high () |
| Thermal Stability | Negative tempco (thermal runaway risk) | Negative tempco of mobility (thermally stable) | Negative tempco of mobility (thermally stable) |
Complementary MOS (CMOS)
CMOS Construction and Principle
CMOS (Complementary Metal–Oxide–Semiconductor) integrates both an -channel E-MOSFET (NMOS) and a -channel E-MOSFET (PMOS) symmetrically on a single silicon wafer (typically an -well inside a -type substrate):
- PMOS Pull-Up Network (PUN): Connects between and output ; conducts (closes) when its gate input is LOW ().
- NMOS Pull-Down Network (PDN): Connects between output and (); conducts (closes) when its gate input is HIGH ().
- Key Advantage: In every steady logic state, one network is ON and the complementary network is OFF, so there is no direct DC path from to —giving near-zero static power dissipation, full rail-to-rail output swing ( to ), and high noise margins.
5.6 MOSFET as logic circuits
MOSFETs dominate modern digital VLSI (microprocessors, memory, ASICs) because they scale cleanly to nanometer dimensions, require no passive base/collector resistors in CMOS, and consume power primarily only while switching.
- NMOS Logic Inverter (Resistive-Load or Depletion-Load):
- Driver NMOS (source grounded, gate = ) with load resistor (or depletion NMOS) to .
- : OFF (HIGH).
- : ON in triode (LOW), but static current flows through and , wasting standby power.
- CMOS Inverter (NOT Gate, ):
- Gates of PMOS (, source at ) and NMOS (, source at ) are tied together to input ; drains tie together to output .
- : ( OFF) and ( ON) (Logic ).
- : ( ON) and ( OFF) (Logic ).
- CMOS NAND and NOR Gates (Series–Parallel Duality Rule):
- 2-Input CMOS NAND (): Two PMOS in parallel in the PUN (output pulled HIGH if OR ); two NMOS in series in the PDN (output pulled LOW only if AND ).
- 2-Input CMOS NOR (): Two PMOS in series in the PUN (output pulled HIGH only if AND ); two NMOS in parallel in the PDN (output pulled LOW if OR ).
- Dynamic Power Dissipation in CMOS: Every time a CMOS gate switches a load capacitance at clock/switching frequency (with cycle per period), energy is drawn from , giving:
| Gate | Boolean Function | Pull-Up Network (PMOS) | Pull-Down Network (NMOS) | Output LOW Condition |
|---|---|---|---|---|
| CMOS NOT | PMOS | NMOS | ||
| CMOS NAND2 | PMOS in parallel | NMOS in series | AND | |
| CMOS NOR2 | PMOS in series | NMOS in parallel | OR |
Worked Out Examples
5.4
An NPN silicon BJT is used as a saturated digital inverter switch with , , , , and . When the input is (Logic HIGH), design the maximum allowable base resistor using an overdrive factor of () to guarantee hard saturation.
Collector saturation current and minimum base current: When the transistor is saturated, :
Minimum base current needed at the edge of saturation (using worst-case ):
Applying overdrive factor and calculating : For an overdrive factor of :
Applying KVL around the base input loop ():
Any standard resistor (such as or ) guarantees hard saturation.
, , design , and .
5.5
- An -channel JFET has and pinch-off voltage . Calculate its drain current and transconductance in the saturation region when .
- An -channel E-MOSFET has threshold voltage and conduction parameter . It is biased with , , and drain resistor (source grounded). Find and , and verify that the MOSFET operates in the saturation region.
1. JFET drain current and transconductance: Using Shockley's equation with , , and :
2. E-MOSFET operating point and saturation check: Assuming saturation ():
The drain-to-source voltage is:
Checking the saturation boundary condition :
confirming that the E-MOSFET is indeed in saturation.
- JFET: , .
- E-MOSFET: , (, verified in saturation).
5.6
- Trace the state (ON/OFF) of every transistor in a 2-input CMOS NAND gate ( in parallel; in series) for all four input combinations , verifying the output .
- If this CMOS gate drives a load capacitance from at a switching frequency , calculate its dynamic power dissipation .
1. Transistor-level verification of 2-input CMOS NAND: Remember: an NMOS conducts when its gate is (), whereas a PMOS conducts when its gate is ().
| (Parallel PUN) | (Parallel PUN) | (Series PDN) | (Series PDN) | Output | ||
|---|---|---|---|---|---|---|
| ON | ON | OFF | OFF | () | ||
| ON | OFF | OFF | ON | () | ||
| OFF | ON | ON | OFF | () | ||
| OFF | OFF | ON | ON | () |
Notice that in every row, the PUN and PDN never conduct simultaneously, and the output matches the NAND truth table.
2. Dynamic power dissipation:
- The PUN () pulls whenever either or ; the PDN ( in series with ) pulls only when , implementing .
- .
Exercises
Practice Exercises — Transistor (Part 2: 5.4–5.6)
Explain how a BJT operates as an electronic switch in cutoff and saturation, and describe why storage time () limits the switching speed of a saturated BJT.
BJT Cutoff and Saturation as a Switch:
- Cutoff (Switch OPEN): With , both junctions are reverse-biased, and , so (output HIGH).
- Saturation (Switch CLOSED): With sufficient base current (), both junctions are forward-biased, is limited externally by , and (output LOW).
Storage Time () Limitation: In hard saturation, excess minority carriers accumulate inside the base region (and collector). When the input switches back to cutoff, cannot drop immediately until this excess stored base charge is swept out or recombined. This delay—called storage time —dominates total turn-off time and limits switching frequency.
A BJT switch toggles between cutoff (, , open switch) and saturation (, closed switch). Turn-off speed is limited by storage time (), the interval needed to clear excess minority carriers stored in the base during saturation.
An NPN BJT switching circuit has , , , , and . If the input pulse switches between and , find:
- when (switch OFF).
- and when .
- The value of needed to achieve an overdrive factor of ().
OFF state and saturation currents:
- When , the BJT is in cutoff (), so .
- When saturated:
Base resistor for overdrive factor :
- when .
- , .
- .
An -channel JFET has and .
- Find the drain current and transconductance at (in pinch-off/saturation).
- State the minimum drain-to-source voltage required to keep the JFET in the pinch-off (constant-current) region at .
Drain current and transconductance :
Pinch-off boundary : For an -channel JFET, the channel pinches off at the drain when , i.e., :
- , .
- .
An -channel enhancement MOSFET has and . Given , determine its operating region and calculate when:
Case 1: : Here . Since , the MOSFET is in the triode (ohmic) region:
Case 2: : Since , the MOSFET is in the saturation region:
- Triode region: .
- Saturation region: .
Describe the transistor-level construction of a CMOS inverter and a 2-input CMOS NOR gate. Why does CMOS consume almost zero static DC power compared to NMOS resistive-load logic?
CMOS Inverter and 2-Input CMOS NOR Gate:
- CMOS Inverter (): A PMOS transistor (, source to ) and an NMOS transistor (, source to ) share gate input and drain output . When , conducts and is off (); when , conducts and is off ().
- 2-Input CMOS NOR (): Two PMOS transistors connected in series between and form the pull-up network (conducts only when AND ), while two NMOS transistors connected in parallel between and form the pull-down network (conducts whenever OR ).
Why CMOS Has Near-Zero Static Power Dissipation: In an NMOS resistive-load inverter, whenever the NMOS driver is ON (), continuous DC current flows from through and the NMOS to ground. In CMOS, the pull-up (PMOS) and pull-down (NMOS) networks are strictly complementary: in any steady logic state, one network is ON and the other is OFF, breaking any DC path between and except for tiny nanoampere leakage.
A CMOS inverter pairs one PMOS pull-up with one NMOS pull-down; a 2-input CMOS NOR uses two series PMOS (PUN) and two parallel NMOS (PDN). CMOS consumes near-zero static power because in every steady logic state either the PUN or PDN is OFF, preventing continuous DC current between and .