Transistor (part 1: 5.1–5.3)
Open in the Padhaiko app5.1 BJT configuration and biasing, small and large signal model
A Bipolar Junction Transistor (BJT) is a three-terminal, current-controlled semiconductor device consisting of two junctions back to back (NPN or PNP), with three doped regions: Emitter () (heavily doped), Base () (thin and lightly doped), and Collector () (moderately doped, largest area).
Operating Regions and Current Relations
By KCL at the transistor terminals and carrier injection physics:
where () is the common-base DC current gain and () is the common-emitter DC current gain.
| Region | Base–Emitter () Junction | Base–Collector () Junction | Behavior & Typical Application |
|---|---|---|---|
| Active (Forward-Active) | Forward-biased () | Reverse-biased () | (linear current amplification) |
| Cutoff | Reverse-biased () | Reverse-biased | (open switch) |
| Saturation | Forward-biased () | Forward-biased () | (closed switch) |
| Reverse-Active | Reverse-biased | Forward-biased | Inverted emitter/collector with low (rarely used) |
Three BJT Amplifier Configurations
Depending on which terminal is common to both input and output ports, a BJT operates in Common-Base (CB), Common-Emitter (CE), or Common-Collector (CC / Emitter Follower) configuration.
| Characteristic | Common-Base (CB) | Common-Emitter (CE) | Common-Collector (CC / Emitter Follower) |
|---|---|---|---|
| Input / Output Terminals | Input: , Output: | Input: , Output: | Input: , Output: |
| Current Gain () | Low () | High () | High () |
| Voltage Gain () | High (non-inverting) | High (inverting, phase shift) | Unity (, non-inverting) |
| Input Impedance () | Very low () | Moderate () | Very high () |
| Output Impedance () | Very high () | Moderate to high () | Very low () |
| Primary Application | High-frequency / RF wide-band stages | General-purpose voltage & power amplification | Impedance matching / voltage buffer |
DC Biasing and -Point Stabilization
Biasing establishes a stable DC quiescent operating point (-point: ) in the middle of the active region so AC signals amplify without clipping, even when or temperature varies.
- Fixed-Bias Circuit: Base resistor from to base gives and . Simple, but poor stability because varies directly with .
- Collector-to-Base Feedback Bias: Connects from collector to base; negative feedback partially stabilizes :
- Voltage-Divider (Self) Bias: Uses and at the base plus an emitter resistor . Replacing the divider with its Thevenin equivalent:
applying KVL around the base–emitter loop gives:
When (typically ), and , making the -point nearly independent of .
- DC Load Line: For a CE stage with and (), is a straight line with intercepts (at ) and (at ).
Large-Signal vs. Small-Signal Models
| Aspect | Large-Signal Model | Small-Signal Model |
|---|---|---|
| Signal Amplitude | Full-swing DC + large AC / switching signals () | Tiny AC perturbations around a fixed DC -point () |
| Mathematical Form | Nonlinear Ebers–Moll exponential () or piecewise-linear (Active / Cutoff / Saturation) | Linearized circuit with -point-dependent constants () |
| DC Supplies | Active ( sets bias levels) | Replaced by AC ground (short-circuited); coupling/bypass capacitors act as AC shorts |
| Purpose | Finding -point, switching states, saturation/cutoff limits | Computing AC voltage gain , current gain , , and |
5.2 T and π model
For small AC signals () superimposed on an active-region -point (), the BJT behaves as a linear two-port modeled equivalently by the Hybrid- model or the T-model.
Small-Signal Parameters of the BJT (at Room Temperature, VT = 26 mV)
- Transconductance (): Slope of versus at the -point:
- Base–Emitter Input Resistance (): Small-signal resistance looking into the base with emitter grounded:
- Emitter Dynamic Resistance (): Small-signal resistance looking into the emitter with base grounded:
- Output Resistance (, Early Effect): Finite collector–emitter output resistance due to base-width modulation:
- Hybrid- Model: Input resistor connects between Base () and Emitter () with base signal voltage ; a voltage-controlled current source (equivalently ) flows from Collector () to Emitter (), with in parallel between and .
- T-Model ( Model): Dynamic resistor connects between Emitter () and an internal junction node connected directly to Base (), carrying emitter current ; a current-controlled current source (equivalently ) flows from Collector () to Base/internal node.
- Equivalence: Both models produce identical terminal currents and gains because and .
- Bypassed CE Amplifier ( shorted at AC, ):
- Unbypassed CE Amplifier (with in emitter):
5.3 Concept of differential amplifier using BJT
A differential amplifier amplifies the difference between two input signals () while strongly rejecting any common-mode interference (such as hum or thermal drift) appearing equally on both inputs. It forms the input stage of virtually every operational amplifier.
BJT Differential Pair: Differential Mode, Common Mode, and CMRR
Consider a symmetrical emitter-coupled pair of matched transistors and with equal collector resistors , fed at their joined emitters by a tail current source (or tail resistor to ):
- Differential and Common-Mode Inputs:
- Differential-Mode Operation (): By symmetry, the common emitter node stays at virtual AC ground ():
- Double-ended (differential) voltage gain: (magnitude ).
- Single-ended differential gain: (or at ).
- Differential input resistance: .
- Common-Mode Operation (): By symmetry, the circuit splits into two identical half-circuits, each seeing in its emitter:
- Double-ended common-mode gain: (for matched and ).
- Single-ended common-mode gain:
- Common-Mode Rejection Ratio (CMRR): Measures how effectively the amplifier favors differential signals over common-mode noise:
Worked Out Examples
5.1
A voltage-divider biased silicon NPN CE circuit has , , , , , , and . Using exact Thevenin analysis, find the -point ( and ) and verify that the transistor is in the active region.
Thevenin equivalent of the base bias divider:
Solving for base, collector, and emitter currents: Applying KVL around the base–emitter loop ():
Computing and checking operating region: Applying KVL along the collector–emitter path:
Since and , the transistor is squarely in the forward-active region.
The -point is , (forward-active region).
5.2
A common-emitter BJT amplifier is biased at with , , and . The base bias divider has , the collector resistor is , the load resistor is , and the emitter resistor is fully bypassed by a large capacitor. Calculate:
- The small-signal hybrid- parameters () and the T-model parameter ().
- The amplifier input resistance , output resistance , and unloaded/loaded AC voltage gain .
Small-signal hybrid- and T-model parameters:
Input resistance, output resistance, and voltage gain: Looking into the base with the emitter AC-grounded, :
Looking back into the collector (with and independent sources zeroed):
The combined AC collector load is , giving:
- , , .
- , , ( phase inversion).
5.3
A matched BJT differential amplifier has a tail current supplied by a tail resistor , collector resistors , and transistors with (, , ). Calculate:
- The differential input resistance .
- The single-ended differential voltage gain and double-ended differential voltage gain .
- The single-ended common-mode gain and the single-ended (in ratio and in ).
Quiescent current and small-signal parameters per transistor: With matched and , the tail current divides equally ():
Differential input resistance and differential gains: Between the two bases, the two base–emitter resistances appear in series:
Using the differential half-circuit (virtual AC ground at emitter):
Common-mode gain and CMRR (single-ended output):
- .
- , .
- , ().
Exercises
Practice Exercises — Transistor (Part 1: 5.1–5.3)
Compare the Common-Base (CB), Common-Emitter (CE), and Common-Collector (CC) BJT configurations in terms of voltage gain, current gain, phase relationship, input impedance, and output impedance. Why is voltage-divider biasing preferred over fixed biasing?
Comparison of CB, CE, and CC Configurations:
- Common-Base (CB): High voltage gain (non-inverting), current gain , very low , very high (RF stages).
- Common-Emitter (CE): High voltage gain ( phase inversion), high current gain , moderate and (most widely used voltage amplifier).
- Common-Collector (CC): Unity voltage gain (, non-inverting), high current gain , very high , very low (buffer/impedance matching).
Why Voltage-Divider Bias Beats Fixed Bias: In fixed bias, scales directly with , which varies widely with temperature and manufacturing tolerances, causing -point drift or thermal runaway. In voltage-divider bias with emitter resistor , any increase in raises , reducing and counteracting the current rise (negative feedback), stabilizing the -point.
CE provides high voltage and current gain with inversion; CB offers low and high with unity current gain; CC offers unity voltage gain with high and low . Voltage-divider bias with uses emitter negative feedback to keep insensitive to variations in and temperature.
A fixed-bias silicon NPN CE circuit has , , , , and .
- Find the quiescent operating point ().
- State the DC load-line intercepts ( and ).
- If the transistor is replaced by one with , calculate the new and .
Initial -point ():
DC Load-Line Intercepts and Effect of : From :
- Cutoff intercept (): .
- Saturation intercept (): .
With ( unchanged at ):
(A change in shifts by , illustrating fixed-bias instability.)
- , , .
- Load-line intercepts: , .
- For : , .
A BJT is biased at and has , Early voltage , and . Compute the hybrid- parameters , , and , as well as the T-model emitter resistance .
Transconductance and output resistance :
Input resistance and T-model resistance :
(), , , and .
Using the T-model ( model), analyze an unbypassed common-emitter stage with , (no external load, ), , and . Find the small-signal base input resistance and the voltage gain .
Base input resistance : In the T-model, flows through the series combination :
Small-signal voltage gain : With , the collector current is and :
and .
A BJT differential amplifier has a differential gain and a of .
- Calculate the numerical ratio and the common-mode gain .
- If the two input voltages are and (taking ), compute the differential input , common-mode input , and total output voltage .
Numerical CMRR and common-mode gain:
Differential/common-mode components and output voltage:
- , .
- , , and .