The Bipolar Junction Transistor (BJT) (part 1: 1.1–1.6)
Open in the Padhaiko app1.1 Review of operation of the npn transistor in the active mode
npn Transistor in the Active Mode
A BJT has three regions, emitter (heavily doped), base (very thin, lightly doped) and collector (moderately doped), forming two junctions. In the active mode the emitter-base junction (EBJ) is forward biased and the collector-base junction (CBJ) is reverse biased.
- The forward-biased EBJ injects electrons from the emitter into the base.
- The base is so thin that most electrons diffuse across it and are swept into the collector by the CBJ field. A small fraction recombines in the base, forming the base current .
- Collector current: , where at room temperature.
- , , , , with
For a silicon transistor when conducting.
| Mode | EBJ | CBJ | Use |
|---|---|---|---|
| Cutoff | reverse | reverse | switch OFF |
| Active | forward | reverse | amplifier |
| Saturation | forward | forward | switch ON () |
| Reverse active | reverse | forward | rarely used |
1.2 Review of graphical representation of transistor characteristics
BJT Characteristics
- Input characteristic ( against at fixed ): like a forward diode, with a cut-in near and in normal use.
- Output characteristic ( against for steps of ): a family of curves. For small (below about ) the transistor is in saturation. Above that the curves are nearly flat (active region) with a slight upward slope due to the Early effect: , so . The region below is cutoff.
- Transfer characteristic: against (slope ) or against (exponential).
1.3 Analysis of transistor circuits at DC
DC Analysis Procedure
- Assume the BJT is in the active mode: , , .
- Write KVL around the base-emitter loop to find (or ), then .
- Write KVL around the collector-emitter loop to find .
- Check: (and ). If the assumption fails, so set and .
1.4 Graphical DC load line analysis
DC Load Line and Q-Point
KVL on the output loop gives , a straight line on the output characteristics.
- Intercepts: at (saturation end) and at (cutoff end).
- Its intersection with the characteristic for the bias current is the quiescent (Q) point, .
- For maximum symmetrical output swing the Q-point sits near the middle of the load line. If it is too high on the line the output clips at saturation; too low and it clips at cutoff.
1.5 Transistor as an amplifier (, , )
Small-Signal Parameters
For small signals around the Q-point, with the DC collector current:
The transistor behaves as a voltage-controlled current source: . A common-emitter stage with collector resistor has unloaded voltage gain
negative because the output is inverted. A larger gives larger but also needs more supply.
1.6 Biasing BJT for discrete-circuit design
Biasing and Stability
Biasing sets a stable Q-point despite changes in and temperature. Stability factor : the smaller, the more stable.
- Fixed bias: . Simple but varies fully with (): poor.
- Collector-feedback bias: from collector to base. Negative feedback improves stability.
- Emitter-stabilised / voltage-divider bias: divider sets the base voltage, provides negative feedback. Design rule: so is nearly independent of . Rule of thumb: about across , across , across (or to on the emitter).
- Dual-supply emitter bias: , which is the most stable.
1.1
Find the Q-point of a voltage-divider bias circuit with , , , , , , .
Thevenin base circuit.
Base and collector currents.
Collector-emitter voltage.
This exceeds , so the active-mode assumption is valid.
, (active mode).
1.2
A fixed-bias circuit has , , and . Draw the DC load line, find the Q-point and the stability factor.
Load line. At : . At : .
Q-point. , so and .
Assessment. The Q-point lies slightly below the load-line midpoint (, ). Stability factor of fixed bias: , so changes by times any change in leakage current.
Load line to ; Q-point ; .
1.3
A BJT with is biased at with . Find , and , and the unloaded voltage gain of a CE stage with .
Transconductance. .
Input resistances. and .
Gain. V/V.
, , , .
Exercises
Practice Exercises: BJT Operation, DC Analysis and Biasing
State the junction biasing for the four BJT modes. Why is voltage-divider bias preferred to fixed bias, and what design condition makes it stable?
Modes. Active: EBJ forward, CBJ reverse. Cutoff: both reverse. Saturation: both forward. Reverse active: EBJ reverse, CBJ forward.
Stability. In voltage-divider bias gives negative feedback: if rises the emitter voltage rises, which reduces and . It needs so that becomes independent of .
Voltage-divider bias with .
A fixed-bias circuit has , , , . Find and . What happens if rises to ?
Q-point. , and .
Effect of higher . would double to , so . The transistor saturates: this shows the poor stability of fixed bias.
, ; saturation if .
In a collector-feedback bias circuit, , , (collector to base), , . Find , and .
Base loop. :
Currents and voltage. and . Active, since .
, , .
A dual-supply circuit has , , , , base resistor to ground, . Find , , and .
Emitter current. KVL base loop: , with :
Voltages. . , . So .
, , .
A transistor with and Early voltage is biased at . Find , , and .
Parameters. . . . .
, , , .