The Bipolar Junction Transistor (BJT) (part 2: 1.7–1.11)
Open in the Padhaiko app1.7 Small signal equivalent circuit models ( and T)
Hybrid- and T Models
For signals small enough to keep the exponential nearly linear (), replace the DC sources by their small-signal equivalents (ideal DC voltage source short circuit, DC current source open circuit) and the BJT by one of two equivalent models:
- Hybrid- model: a base resistance between B and E, a voltage-controlled current source from C to E, and an output resistance in parallel with it:
- T model: an emitter resistance between E and B, and a current-controlled current source from C. Relations: , .
1.8 Basic single-stage BJT amplifier configuration (C-B, C-E, C-C)
| Property | Common emitter (CE) | Common base (CB) | Common collector (CC, emitter follower) |
|---|---|---|---|
| Input at, output at | base, collector | emitter, collector | base, emitter |
| Voltage gain | high, inverting: | high, non-inverting: | (slightly below), non-inverting |
| Current gain | (high) | (high) | |
| Input resistance | medium: | very low: | very high: |
| Output resistance | high: | high: | very low: |
| Use | voltage amplifier | high-frequency amplifier, current buffer | voltage buffer, impedance matching |
1.9 Small signal analysis of amplifier
Small-Signal Analysis Procedure
- Perform the DC analysis to get , then find , , , .
- Draw the a.c. equivalent: coupling and bypass capacitors become short circuits, DC supplies are grounded.
- Replace the BJT by the (or T) model.
- Calculate , , and . The overall gain with a source resistance is , and the effect of load: uses .
Key CE results:
- Emitter bypassed: , .
- Emitter resistor not bypassed: , . Gain drops but is more stable and linear.
1.10 Transistor as a switch: cutoff and saturation
BJT Switch
In a switching (inverter) circuit the BJT works only in cutoff (switch OFF, , ) or saturation (switch ON, , ).
- Saturation condition: , that is the forced beta . In practice is made about to times the minimum.
- A logical LOW input gives output HIGH and the reverse, so the circuit is a NOT gate.
- Power loss in the ON state is (small), and in the OFF state .
1.11 A general large-signal model of the BJT: The Ebers-Moll model
Ebers-Moll (Transport) Model
The Ebers-Moll model describes the BJT in all four modes by two back-to-back diodes plus two current sources. In the transport form for an npn:
Here is the saturation current, the forward and the reverse common-emitter current gain.
- Active mode: is negative, the terms vanish and , .
- Saturation: both junctions are forward biased, so the terms matter. They reduce for a given and the collector-emitter voltage falls to , typically to .
1.4
A CE amplifier (emitter bypassed) is biased at with . The bias network resistance is , , and the source resistance is . Find , the voltage gain and the overall gain .
Model parameters. and .
Input resistance. .
Gains. . The input divider is , so
, , .
1.5
An emitter follower is biased at (), . It has , load and a source resistance . Neglect the bias resistors. Find , , and .
Effective load. .
Input resistance and gain. .
Output resistance. Looking back into the emitter: . In parallel with this gives .
, , , .
1.6
A BJT inverter has , , , , , . Show that saturates it, find the output for , and the smallest that saturates it.
Input HIGH. and . Forced beta , so the transistor is saturated and (LOW).
Input LOW. With the EBJ is not forward biased, so and (HIGH).
Smallest saturating input. , so .
HIGH input: saturated, ; LOW input: ; saturation needs .
Exercises
Practice Exercises: BJT Amplifiers, Switch and Ebers-Moll
Compare the CE, CB and CC amplifier configurations in terms of input resistance, output resistance, voltage gain and phase. Give one application of each.
CE. Medium (), high (), high gain , phase shift. Use: general voltage amplifier.
CB. Very low (), high , high gain , in phase, current gain . Use: high-frequency amplifier (no Miller effect), current buffer.
CC. Very high , very low , gain , in phase, high current gain. Use: buffer driving a low-resistance load.
As compared in the table of 1.8.
A CB amplifier has , , . Find , the voltage gain and the output resistance.
Input resistance. .
Voltage gain. (non-inverting).
Output resistance. .
, , .
A CE stage has , , , unbypassed and no load. Find the gain and the resistance looking into the base.
Emitter resistance. so .
Gain. .
Input resistance at the base. .
, . Without the gain would have been , so trades gain for stability.
A BJT switch has , , , . With find the forced beta, state whether it saturates, and give the power dissipated in the transistor. Find the minimum to saturate.
Currents. . .
Forced beta and power. , so it is saturated. .
Minimum drive. , so .
, saturated; ; .
A BJT has , , , . Using the Ebers-Moll model find , and for and .
Exponentials. , and .
Currents. . (the reverse term is negligible). .
, , (active mode).