Power Supplies, Breakdown Diodes, and Voltage Reference
Open in the Padhaiko app5.1 Unregulated power supply
Rectifier and Filter
An unregulated d.c. supply is: transformer rectifier filter capacitor load. Its output changes with line voltage and load current. Rectifier figures of merit are in the table below.
A capacitor filter charges the capacitor to and supplies the load while the rectified voltage is below it. For full-wave rectification with ripple frequency :
A larger or gives lower ripple. Regulation of the unregulated supply: . A bridge rectifier needs a transformer without a centre tap, but two diode drops () are lost.
| Quantity | Half-wave | Full-wave (centre-tap or bridge) |
|---|---|---|
| Ripple factor | ||
| Rectification efficiency | ||
| Peak inverse voltage | (centre-tap), (bridge) | |
| Ripple frequency |
5.2 Zener regulated power supply
Shunt Zener Regulator
A zener diode of breakdown voltage is connected across the load in reverse bias, fed from the unregulated voltage through a series resistor :
- Design: the zener must keep a minimum current at maximum load and minimum input:
- At no load all the current flows through the zener (, with ).
- Line regulation: . Load regulation: , with the zener dynamic resistance.
- Simple and cheap, but wasteful, with limited current (tens of milliamperes).
5.3 Zener diodes, bandgap voltage reference, constant current diodes
Zener Diode, Bandgap Reference and Constant-Current Diode
- Zener diode: heavily doped junction designed for reverse breakdown. Two mechanisms: the zener effect (field emission, ) with a negative temperature coefficient, and avalanche breakdown () with a positive coefficient. Near to they cancel, giving the best stability. Voltage is nearly constant over a wide current range: .
- Bandgap reference: the voltage across a forward falls about , while the voltage developed by two junctions at different current densities rises about for . Adding the two with a gain so the slopes cancel gives a reference near the silicon bandgap of with almost zero temperature drift:
Used in nearly all IC regulators, ADCs and DACs.
- Constant-current (current-regulator) diode: a JFET with its gate shorted to the source. For above a few volts it delivers , nearly independent of voltage, so it acts as a two-terminal current limiter (for LEDs, bias currents).
5.4 Transistor shunt/series voltage regulator
Transistor Series and Shunt Regulators
- Series pass regulator: a power transistor in series with the load, as an emitter follower. A zener holds the base at , so . The transistor supplies the load current and the zener only the base current, so currents are multiplied by : , . dissipates .
- Shunt regulator: a transistor in parallel with the load drawing the surplus current from a series resistor . It is naturally short-circuit proof (the series resistor limits the current), but wasteful because current is drawn all the time.
- A Darlington pass element reduces base current further.
| Feature | Series regulator | Shunt regulator |
|---|---|---|
| Control element | in series with load | in parallel with load |
| Efficiency | good, falls with large | low, constant current always drawn |
| Short-circuit protection | needs a current limit circuit | inherent (series resistor limits) |
| Use | most regulators | simple low-power references |
5.5 Improving voltage regulator performance with feedback
Feedback Regulator
An error amplifier (op-amp or differential pair) compares a sample of the output with a reference and drives the pass transistor. With divider (top) and (bottom):
Negative feedback with loop gain reduces the output resistance and the effect of input variations by :
Additional blocks: current limiting (a sense resistor turning on a limiting transistor at ) and thermal shutdown.
5.6 IC voltage regulator
IC Voltage Regulators
An IC regulator puts the reference, error amplifier, pass transistor and protection on one chip.
- Fixed 78xx / 79xx series: three-terminal (input, ground, output). The 7805 gives at up to , the 7905 gives . The input must be at least to above the output (dropout) and bypass capacitors ( in, out) are recommended.
- Adjustable LM317: keeps between output and adjust:
- Features: internal current limit, thermal shutdown and safe-area protection. Dissipation determines the heat sink needed.
5.1
A full-wave bridge rectifier is fed from a rms secondary at and has a filter capacitor across . Each conducting diode drops . Find the peak voltage, ripple voltage, d.c. output and ripple factor.
Peak. Two diodes conduct, so .
Ripple. and :
D.C. output and ripple factor. and
, , , .
5.2
Design a zener shunt regulator for output from a source, with load current up to and a minimum zener current . Find , the no-load zener current and power. If the input varies by and , how much does the output change?
Series resistor. .
No load. so . A zener or larger is required.
Line variation. (output moves by only of the input change).
, , , .
5.3
An op-amp series regulator uses a zener reference and a divider with . Find the output voltage. If the op-amp gain is and the output resistance without feedback is , find the output resistance with feedback.
Output voltage. .
Feedback. , so :
Load changes of then change by only .
and .
Exercises
Practice Exercises: Power Supplies, Zener and Regulators
Explain the working of a bandgap voltage reference and why its output is near . Distinguish zener breakdown from avalanche breakdown and state what a constant-current diode is.
Bandgap. decreases about (CTAT). The difference of two junctions at different current densities increases with temperature (PTAT). Scaling the PTAT term and adding it to cancels the slopes, giving , close to the silicon bandgap.
Breakdown types. Zener effect: high electric field pulls electrons out of bonds, , negative temperature coefficient. Avalanche: impact ionisation of high-energy carriers, , positive coefficient.
Constant-current diode. A JFET with gate tied to source; current stays near for above a few volts.
Bandgap: CTAT plus PTAT gives ; zener below , avalanche above ; constant-current diode is a gate-shorted JFET.
A peak sine wave is rectified (ideal diodes). Find , ripple factor and efficiency for half-wave and full-wave rectification without a filter.
Half-wave. , , , .
Full-wave. , , , .
Half-wave: , , . Full-wave: , , .
A zener regulator has , , load current to and . Find , the maximum zener power and the power in .
Series resistor. .
Powers. The total current is fixed at . At no load the zener carries it all: . .
, , .
A series-pass regulator uses a zener, a transistor with and , and an input of . For a load find , (with ) and the transistor dissipation.
Output. .
Base drive. , so .
Dissipation. (a heat sink is needed).
, , .
(a) An LM317 has and . Find , and the for (ignore ). (b) A 7805 runs from at : find its dissipation and the smallest input voltage if the dropout is .
(a) . For : , so .
(b) (the quiescent term is small). .
(a) and ; (b) and .