Output Stages and Power Amplifiers (part 2: 4.5–4.8)
Open in the Padhaiko app4.5 Biasing of class AB output stage
Biasing Methods
The bias must hold both bases about apart so that each output transistor has a small .
- Diode bias: two diode-connected transistors in series with a resistor to the supply carry a bias current . They share a voltage with the output transistors' base-emitter junctions, so the diodes and outputs form current mirrors: , where is the ratio of the emitter-junction areas (output : diode). The diodes sit on the same heat sink so they track temperature.
- multiplier: a transistor with resistors (collector to base) and (base to emitter) gives
which is adjustable by choosing and allows exact setting of . Mounted on the heat sink, it reduces as temperature rises.
- Thermal runaway: falls , so a hotter transistor conducts more, gets hotter and so on. Prevented by emitter resistors ( to ) and thermal tracking of the bias network.
4.6 Power BJTs
Power BJTs and Heat Sinking
Power transistors have a large collector area and metal case (TO-3, TO-220) for heat removal, wide emitter structures and usually low ( to ). A Darlington pair raises the current gain to .
Heat flows from the junction to ambient through series thermal resistances (in ), like Ohm's law:
with junction-to-case, case-to-sink and sink-to-ambient resistances. is to for silicon. A transistor must be derated linearly above a stated temperature: allowed .
Other limits: maximum , maximum , and second breakdown (local hot spots from current crowding at high and ) which shrinks the safe operating area (SOA).
4.7 Transformer-coupled push-pull stage
Transformer-Coupled Push-Pull Stage
Two transistors work alternately, driving a centre-tapped output transformer whose centre tap is connected to . A centre-tapped input transformer (or a phase splitter) provides opposite-phase drive. The two collector currents flow in opposite directions through the two halves of the primary, so the DC flux cancels in the core and the second-harmonic distortion cancels.
- Load matching: the transformer reflects the load to the half-primary: , with the turns in half of the primary. The transistor must see its optimum load .
- Power (class B): , .
- Used before complementary stages became common. The transformer is bulky and costly and limits the frequency response, but it gives isolation and matching.
4.8 Tuned amplifiers
Tuned Amplifiers
A tuned amplifier uses a parallel LC circuit as the collector or drain load so that only a narrow band around the resonant frequency is amplified. It is the basic radio-frequency (RF) and intermediate-frequency (IF) stage.
At resonance the tank impedance is purely resistive and equals the parallel resistance (including the load and the transistor output resistance). Voltage gain at resonance:
- Single-tuned: one tank. Double-tuned: two coupled tanks, flatter response and sharper skirts. Stagger-tuned: several stages tuned to slightly different frequencies for a wide flat band.
- A tuned amplifier may be run class C (conducting for under ), because the tank's flywheel effect restores the full sine wave. This reaches an efficiency of about .
- A higher loaded gives narrower bandwidth, more selectivity and more gain.
4.4
A class AB stage has supplies. The bias network is two diode-connected transistors and a resistor from to . Each output transistor has times the junction area of the diodes. Find and . If a multiplier replaces the diodes, what gives and what does give?
Bias current. .
Quiescent current. .
multiplier. with . For : , so (for example each). For : , which gives a larger .
, ; for and for .
4.5
A power transistor has , mounted with on a heat sink with . The ambient temperature is . Find the junction temperature at , the maximum power for , and the sink resistance needed to keep at .
Junction temperature. Total , so .
Maximum power. .
Required sink. so .
, , .
4.6
A tuned amplifier uses and . The loaded is and the transistor has . Find , the bandwidth, the tank resistance at resonance and the voltage gain.
Resonance. .
Bandwidth. .
Tank resistance and gain. , so and
, , , .
Exercises
Practice Exercises: Class AB Bias, Power BJTs, Push-Pull and Tuned Amplifiers
A class B transformer-coupled push-pull stage has . Each transistor must see and the load is . Find the turns ratio (half primary to secondary), the maximum output power and the supply power at full output.
Turns ratio. so .
Power. . With , .
, , .
A power transistor dissipates with and . If and , find the largest allowed .
Total thermal resistance. .
Heat sink. . Check: .
.
A multiplier must provide to bias a class AB stage ( for ). Choose if , and explain how thermal tracking is achieved.
Ratio. gives , so .
Thermal tracking. is mounted on the heat sink of the output transistors. As they warm, of falls about , so falls by that. This lowers and so counters thermal runaway.
.
A tuned amplifier has , , and . Find , bandwidth and gain at resonance. What happens to the bandwidth if is doubled?
Resonance and bandwidth. ; .
Gain. rad/s, , so .
Doubling . The bandwidth halves to and , hence the gain, doubles to .
, , ; doubling halves .
Explain thermal runaway in a BJT power stage, how emitter resistors prevent it, and why second breakdown limits the safe operating area. State the advantage of a class C tuned amplifier.
Thermal runaway. Higher temperature lowers by about , which raises the collector current for a fixed bias voltage. The extra current produces more heat and the cycle repeats until the transistor is destroyed.
Emitter resistors. A rise in drops more voltage in , which reduces the net and limits the current (negative feedback). Thermal tracking of the bias network adds protection.
Second breakdown. At high and the current concentrates in small hot spots, which melt before the average temperature reaches the limit. The SOA is therefore narrower than the hyperbola alone suggests.
Class C. Efficiency up to about because the transistor conducts only briefly, while the tank restores the sine wave.
Emitter resistors give negative feedback against thermal runaway; class C gives high efficiency with a tuned load.