PadhaikoAll subjects

Energy Storage

Energy, Environment and Social Engineering (ENEX 417)

Open in the Padhaiko app

4.1 Forms of energy storage

Energy storage decouples energy generation from energy consumption in time and space—smoothing intermittent renewables (solar and wind), supplying peak demand, improving grid frequency stability, and enabling portable/vehicular electrification. Energy is stored across five physical domains:

Major Forms of Energy Storage and Engineering Characteristics
DomainStorage TechnologiesEnergy Storage MechanismTypical Scale & Applications
MechanicalPumped-Storage Hydropower (PSH), Compressed Air (CAES), FlywheelsGravitational potential (), compressed gas pressure, rotational kinetic energy ()Grid bulk storage (MW–GW, PSH/CAES); short-duration UPS & frequency response (flywheels)
ThermalSensible heat (hot water/molten salt), Latent heat (phase-change materials), ThermochemicalTemperature rise (), phase change (), reversible endothermic reactionsSolar thermal water heating, CSP night generation, building HVAC cold/heat storage
ElectrochemicalSecondary batteries (Li-ion, Lead-acid, NiMH, Na-S), Redox Flow BatteriesReversible oxidation–reduction (redox) reactions across anode, cathode, and electrolyteEVs, solar PV off-grid/hybrid systems, telecom backup, grid microgrids
ChemicalHydrogen (), synthetic methane, ammoniaEnergy stored in chemical bonds formed via electrolysis or thermochemical synthesisLong-duration seasonal storage, heavy transport, industrial feedstock
Electrical / MagneticSupercapacitors (EDLCs), Superconducting Magnetic Energy Storage (SMES)Electrostatic double-layer charge separation (); magnetic field ()High-power bursts, regenerative braking recovery, voltage sag ride-through

4.2 Hybrid vehicles

A Hybrid Electric Vehicle (HEV) combines an internal combustion engine (ICE) with one or more electric traction motors and an onboard battery pack to capture braking energy and operate the engine near its peak-efficiency point.

Electrified Vehicle Categories

Hybrid Powertrain Architectures

Comparison of Hybrid Vehicle Drivetrain Architectures
ArchitecturePower Flow PathKey CharacteristicsTypical Use
Series HybridICE is mechanically decoupled from wheels and runs at optimum constant RPM; requires larger motor & generatorCity transit buses, diesel-electric locomotives, range-extender EVs
Parallel HybridBoth and mechanically coupled to wheels via transmissionSmaller battery and motor; direct mechanical drive minimizes double conversion losses on highwaysPassenger mild/full hybrids, motorcycles
Series-Parallel (Power-Split)Planetary gearset blends series and parallel paths simultaneouslyComputer splits ICE torque between generator and wheels for peak efficiency in both city and highway drivingModern full-hybrid passenger cars (e.g., e-CVT power-split designs)

4.3 Grid-to-Vehicle(G2V) and Vehicle-to-Grid(V2G) system

As EV adoption scales, EV batteries form a massive distributed energy storage resource connected to the power grid through smart bidirectional chargers:

AspectGrid-to-Vehicle (G2V)Vehicle-to-Grid (V2G)
Power Flow DirectionUnidirectional ()Bidirectional ()
Control ObjectiveSmart/coordinated charging scheduled during off-peak or high-solar/wind hours (valley filling)Discharging stored battery energy back to the grid during peak demand or contingencies (peak shaving & ancillary services)
Grid BenefitsPrevents transformer overloads from simultaneous evening charging; absorbs surplus renewablesSupplies fast frequency regulation, spinning reserve, and local voltage support
Key ChallengesRequires smart-charging tariffs and communication standards (ISO 15118 / OCPP)Additional charge–discharge cycling accelerates battery degradation; needs fair owner compensation and guaranteed minimum State of Charge ()

4.4 Smart grid systems and demand side management

Definition

Smart Grid

A Smart Grid is an electricity network that integrates two-way power flows (distributed rooftop solar, storage, EVs) with two-way digital communication, automated sensors (smart meters, PMUs), and computer-controlled protection to deliver reliable, efficient, self-healing, and low-carbon electricity.

Core Building Blocks of a Smart Grid

  1. Advanced Metering Infrastructure (AMI): Two-way smart meters recording interval consumption, voltage quality, and real-time pricing signals.
  2. Distribution Automation & Self-Healing: Automated reclosers and SCADA fault isolation reroute power around damaged lines within seconds.
  3. Distributed Energy Resource (DER) Integration: Coordinates rooftop solar inverters, battery energy storage systems (BESS), and V2G fleets.

Demand Side Management (DSM)

Demand Side Management (DSM) comprises utility planning, tariffs, and automated control programs that influence when and how much electricity consumers draw—improving the system load factor and deferring expensive peaking power plants.

Six Classical DSM Load-Shaping Techniques
DSM TechniqueLoad Curve ChangePractical Example
Peak ClippingCuts high peak demand directlyDirect load control turning off water heaters/AC compressors during peak hours
Valley FillingBuilds off-peak demand to use surplus baseload/hydroCheap night tariffs for EV G2V charging or pumped-storage pumping
Load ShiftingMoves demand from peak hours to off-peak hoursTime-of-Use (ToU) tariffs shifting industrial pumping, laundry, or thermal ice storage to night
Strategic ConservationReduces total energy use across all hoursRebates for LED lighting, Energy Star appliances, and building insulation
Strategic Load GrowthIntentionally raises clean electricity demandElectrifying cooking (induction) and transport (EVs) to utilize wet-season surplus hydro
Flexible Load ShapeDynamically matches load to renewable supplyAutomated Demand Response (DR) adjusting data-center or HVAC loads to real-time grid signals

4.5 Battery technologies

An electrochemical battery stores energy via reversible oxidation–reduction reactions at two electrodes (anode and cathode) separated by an ion-conducting, electronically insulating electrolyte.

Definition

Key Battery Parameters

Comparison of Major Rechargeable Battery Technologies
Battery ChemistryNominal Cell VoltageSpecific Energy ()Typical Cycle LifeRound-Trip EfficiencyKey Strengths & Limitations
Lead-Acid (Flooded / AGM / Gel) (at DoD)Low upfront cost, mature recycling; heavy, low DoD tolerance, gassing (flooded)
Nickel-Metal Hydride (NiMH)Robust abuse tolerance, used in early HEVs; high self-discharge
Lithium-Ion (NMC / NCA)High energy density for EVs/laptops; requires BMS to prevent thermal runaway
Lithium Iron Phosphate ( / LFP) (at DoD)Excellent thermal stability, long life, cobalt-free; ideal for solar PV & stationary storage
Vanadium Redox Flow (VRFB)Power (stack) & energy (tank size) scale independently, non-flammable; bulky, stationary only

4.6 Super-capacitors

Definition

Super-capacitor (Ultracapacitor)

A super-capacitor stores electrical energy electrostatically (and/or via rapid surface pseudocapacitance) rather than through slow bulk chemical phase changes. In an Electric Double-Layer Capacitor (EDLC), ions from an electrolyte accumulate on high-surface-area activated-carbon electrodes separated by nanometers (), yielding capacitances from tens to thousands of farads:

Because terminal voltage drops linearly as charge leaves, the usable energy extracted between and is:

AspectLithium-Ion BatterySuper-capacitor (EDLC)
Storage MechanismFaradaic bulk electrochemical redox reactionsElectrostatic double-layer ion adsorption (no bulk chemical reaction)
Energy DensityHigh ()Low ()
Power DensityModerate ()Very high (; rapid charge/discharge in seconds)
Cycle Life cycles cycles
Voltage BehaviorNearly flat discharge plateauVoltage drops linearly with state of charge ()
Optimal RoleSustained energy supply over hoursRegenerative braking bursts, peak-power buffering in hybrid battery–supercapacitor packs

Worked Examples

Example 4.1

4.1

A solar energy storage bank uses modules wired to provide nominal capacity. The battery management system (BMS) restricts maximum Depth of Discharge to , and the discharge efficiency is . Calculate:

  1. Total nominal stored energy ().
  2. Usable energy delivered to the DC bus ().
  3. Discharge current and operating duration when discharging at a rate down to .

1. Nominal Stored Energy:

2. Usable Delivered Energy:

3. Discharge Current and Runtime at :

To extract of nominal capacity () at :

Answer:
  1. Nominal stored energy:
  2. Usable energy:
  3. Discharge current at : ; runtime to DoD:
Example 4.2

4.2

A super-capacitor bank with equivalent capacitance is charged to its rated voltage . During a peak-power pulse, its DC-DC converter operates down to . Calculate:

  1. Total electrostatic energy stored at (in ).
  2. Usable energy extracted between and (in ), and the percentage of total energy utilized.

1. Total Stored Energy at :

2. Usable Energy Between and :

Answer:
  1. Total stored energy:
  2. Usable energy (): ( utilization)
Example 4.3

4.3

A smart-grid parking hub aggregates electric vehicles under a Vehicle-to-Grid (V2G) peak-shaving program. Each EV has a battery arriving at , with drivers requiring a minimum reserve. If bidirectional inverter discharge efficiency is , calculate the total AC energy () and average AC power () the fleet can inject into the grid over a -hour evening peak.

1. Usable DC and AC Energy per Vehicle: Available window ():

2. Fleet Total AC Energy and Average Power:

Answer:

The V2G fleet can deliver of AC energy at an average power of () over the -hour peak.


Exercises

Practice Exercises — Energy Storage

Question 1

Classify the major forms of energy storage with one representative technology and primary grid or engineering application for each.

Five Forms of Energy Storage:

  1. Mechanical: Pumped-Storage Hydro (grid bulk diurnal storage) and Flywheels (seconds-scale frequency stabilization).
  2. Thermal: Molten-salt / hot-water tanks and phase-change materials (solar thermal / CSP overnight heat storage).
  3. Electrochemical: / Lead-acid / Redox flow batteries (EVs, solar microgrids, UPS backup).
  4. Chemical: Green hydrogen (seasonal energy storage and heavy fuel substitution).
  5. Electrical / Magnetic: Supercapacitors and SMES (high-power transient buffering and regenerative braking).
Answer:

Energy storage spans mechanical (PSH, flywheels), thermal (sensible/latent heat), electrochemical (Li-ion, lead-acid, flow batteries), chemical (hydrogen), and electrical/magnetic (supercapacitors, SMES) forms, selected according to required discharge duration and power density.

Question 2

Compare Series, Parallel, and Series-Parallel hybrid electric vehicle architectures, and explain the role of regenerative braking.

Hybrid Drivetrain Architectures:

  • Series Hybrid: Only the electric motor drives the wheels; the ICE turns a generator to charge the battery/power the motor. Best for stop-and-go city driving, but suffers double energy conversion at highway cruise.
  • Parallel Hybrid: Both ICE and electric motor mechanically drive the wheels. Compact and efficient at highway speeds, though ICE speed fluctuates with wheel speed.
  • Series-Parallel (Power-Split): Uses a planetary gearset so power can flow both mechanically and electrically simultaneously, optimizing efficiency across all speeds.

Role of Regenerative Braking: During deceleration or downhill driving, the traction motor operates as a generator, converting vehicle kinetic/potential energy back into electrical energy stored in the battery or supercapacitor instead of wasting it as brake friction heat.

Answer:

Series hybrids decouple the ICE from the wheels via a generator-motor path; parallel hybrids couple both ICE and motor mechanically to the drivetrain; and series-parallel hybrids blend both modes via a planetary power-split. Regenerative braking recovers kinetic energy during deceleration by running the traction motor as a generator.

Question 3

Distinguish between Grid-to-Vehicle (G2V) and Vehicle-to-Grid (V2G) systems, and explain how Demand Side Management (DSM) techniques improve power-grid reliability in a Smart Grid.

G2V vs. V2G: In G2V, smart chargers coordinate unidirectional EV charging during off-peak or high-renewable hours (valley filling). In V2G, bidirectional chargers allow parked EVs to inject power back to the grid during peak demand or frequency dips (peak shaving and ancillary services), requiring battery-degradation management and minimum- guarantees.

DSM in a Smart Grid: Using AMI smart meters and automated demand response, DSM reshapes load profiles via peak clipping, valley filling, load shifting, strategic conservation, strategic load growth, and flexible load shaping—raising system load factor, reducing peak-generation costs, and preventing feeder overloads.

Answer:

G2V coordinates unidirectional smart charging during off-peak hours, while V2G enables bidirectional discharge from EVs to support grid peaks and frequency. Within a Smart Grid, DSM uses smart metering and dynamic tariffs to clip peaks, fill valleys, and shift loads, boosting grid reliability and asset utilization.

Question 4

A , lead-acid battery bank powers a DC telecom load. To preserve cycle life, maximum Depth of Discharge is limited to (ignore converter losses). Calculate the usable energy in and the backup runtime in hours.

Usable Energy:

Backup Runtime:

Answer:

Usable energy: (); backup runtime: .

Question 5

A single super-capacitor cell has capacitance and rated voltage .

  1. Calculate the energy released (in ) when it discharges from to .
  2. Why are super-capacitors often paired with Li-ion batteries rather than used alone as the primary energy store in EVs?

1. Energy Released:

2. Rationale for Hybrid Battery–Supercapacitor Systems: Super-capacitors have very low specific energy ( vs. for Li-ion), so using them alone for long driving range would be prohibitively heavy and bulky. Pairing them allows the super-capacitor to absorb high-current acceleration and regenerative-braking pulses while the battery supplies steady cruise energy, extending battery life.

Answer:
  1. Energy released:
  2. Super-capacitors have low energy density compared to Li-ion batteries, so hybridizing them combines the super-capacitor's high peak-power pulse capability and million-cycle durability with the battery's high sustained energy storage.
← Green Energy SourcesDesign of Solar PV System →