Developments and Intersections
Open in the Padhaiko app6.1 Introduction and projection of solids with points transfer
Sheet-metal fabrication (ducts, hoppers, boilers, chutes, pipe elbows) requires unfolding 3D solid surfaces flat onto sheet stock before cutting and bending, and marking accurate cut-outs where two components join. Both tasks start from clean orthographic projections of solids and point transfer across views.
Classification of Solids
- Polyhedra (Plane-Faced Solids): Bounded entirely by flat polygonal faces:
- Regular Polyhedra: Tetrahedron (4 equilateral triangles), Hexahedron/Cube (6 squares), Octahedron (8 triangles), Dodecahedron (12 pentagons), Icosahedron (20 triangles).
- Prisms: Two identical parallel polygonal bases joined by rectangular (right prism) or parallelogram (oblique prism) lateral faces.
- Pyramids: One polygonal base and triangular lateral faces converging to a single apex (vertex).
- Solids of Revolution (Curved Solids): Generated by revolving a plane figure about an axis:
- Cylinder: Rectangle revolved about one side (right circular cylinder) or sheared oblique cylinder.
- Cone: Right triangle revolved about one perpendicular leg.
- Sphere: Semicircle revolved about its diameter.
- Frustum vs. Truncated Solid: Cutting a pyramid or cone parallel to its base and removing the top leaves a frustum; cutting any solid by an inclined (oblique) section plane leaves a truncated solid.
Projection of Solids and Point Transfer on Surfaces
When a solid's axis is inclined to one or both principal planes, projections are drawn in two or three stages (Change of Position method):
- Stage 1 (Simple Position): Place the solid upright on HP (or VP) so its base appears in True Shape in one view and the axis is perpendicular to XY.
- Stage 2 (Axis Tilted to First Plane): Tilt the edge/elevation view to the given inclination theta to HP (or phi to VP) and project the foreshortened second view.
- Stage 3 (Rotated Relative to Second Plane): Rotate the second view to the required angle with VP/HP and project the final view.
Point Transfer on Solid Surfaces: To locate a point P given in one view (e.g., Front View p') onto the Top View and Side View:
- On a Prism or Cylinder: Pass a vertical edge or surface generator through
p'parallel to the axis, locate where that generator sits on the base circle/polygon in the Top View, and projectp'vertically down onto that generator atp. - On a Pyramid or Cone: Draw a slant generator from the apex
o'throughp'down to the base line atk'. Projectk'down to the base boundary in the Top View (k), draw radial generatoro–kin the Top View, and dropp'vertically ontoo–kto locatep(or use a horizontal circular cross-section at heightp').
6.2 Developments: General concepts and practical considerations, triangulation method for approximate development of surfaces of a right/oblique; Prism, cylinder, pyramid, cone, prism and cylinder cut by oblique planes, frustum/truncated pyramid and cone, transition pieces for connecting different shapes and sphere
A development is the complete unrolled flat pattern of all surfaces of a 3D solid laid out side-by-side in True Size and True Shape.
General Concepts and Practical Sheet-Metal Considerations
- Developable vs. Non-Developable Surfaces: Only single-curved ruled surfaces (cylinders, cones, convolutes) and plane-faced polyhedra (prisms, pyramids) can be flattened without stretching or tearing. Double-curved surfaces (spheres, tori, paraboloids) are non-developable and can only be developed approximately by subdividing into flat zones or gores.
- Seam Placement: Always place the cutting seam along the shortest lateral edge or element to save welding/riveting length and minimize distortion.
- Inside-Up Convention: Standard shop layouts draw the pattern inside-surface up so bending lines and scribed marks end up hidden on the interior of the finished duct or tank.
- Practical Allowances: Real sheet-metal templates add extra lap/seam allowances for riveting, soldering, or grooved seams and bend allowances along fold corners (
BA = angle_rad x (R_inside + K x thickness)), though theoretical geometric developments represent true neutral-surface dimensions.
The Four Surface Development Methods
| Method | Applicable Solids | Core Construction Principle |
|---|---|---|
| 1. Parallel-Line Method | Right & oblique Prisms and Cylinders (full or truncated by oblique planes) | Draw stretch-out line equal to true perimeter (N x side or pi x D) perpendicular to lateral edges/elements; transfer true lengths of each cut edge perpendicularly from the Front View. For oblique prisms/cylinders, project from a right section (plane perpendicular to axis) to get true perpendicular spacing between parallel edges. |
| 2. Radial-Line Method | Right & oblique Pyramids and Cones (full, frustum, or truncated) | Find the True Length (TL) of a slant edge/generator (rotation method). Strike an arc of radius TL centered at apex O; step off base chords (side for pyramid, or chord/arc length theta = (r / L) x 360 deg divided into 12 parts for cone). Rotate all oblique cut points horizontally onto the True-Length extreme generator first, then swing concentric arcs onto their respective radial rays. |
| 3. Triangulation Method | Transition pieces (square-to-round, rectangle-to-circle, oval-to-round), warped chutes, and oblique cones/pyramids | Subdivide the lateral surface into planar triangles connecting base vertices to top vertices. For every triangle edge and diagonal, find its True Length via a True-Length Diagram (TL = sqrt(plan_length^2 + vertical_height^2)). Construct each triangle sequentially using a compass. |
| 4. Approximate (Zone / Lune) Method | Sphere and double-curved shells | Zone (Polyconic) Method: Divide the sphere horizontally into latitudinal strips, treat each strip as a frustum of a tangent cone, and develop each conical band radially. Lune (Gore) Method: Divide the sphere vertically along 12 (or 16) meridians into orange-peel segments (width = pi x D / 12 at equator) and flatten each strip by parallel-line projection along the meridian arcs. |
Developing Special Cases
- Prism or Cylinder Cut by an Oblique Plane: Divide the circular cylinder base into 12 equal parts (1–12), project vertical generators up to the oblique cutting plane in FV, lay out the stretch-out length
pi x Ddivided into 12 equal parts, and project each cut height horizontally across onto the corresponding vertical generator line, joining with a smooth French curve. - Frustum / Truncated Pyramid and Cone: Never measure foreshortened intermediate cut heights directly from interior slant lines! Always project every interior cut point horizontally to the outer True-Length extreme slant edge/generator first, swing an arc with compass centered at the development apex O onto the corresponding radial ray, and connect straight (pyramid) or smooth curves (cone).
- Transition Pieces (e.g., Square-to-Round): Consist of 4 flat triangular faces (each running from one square edge up to a quadrant midpoint of the circle) alternating with 4 conical corner quarters (approximated by subdividing each 90-degree circle quadrant into 3 or 4 equal arcs and triangulating from the adjacent square corner). Build one half-pattern from symmetry, placing the seam along the shortest centerline of a flat triangle.
6.3 Intersections: Lines of intersection of geometric surfaces, piercing point of a line and a geometric solid, intersection lines of two planes, intersections of – prism and prism, cylinder and prism, cylinder and cylinder, pyramid and prism, cone and prism, pyramid and cylinder, cone and cylinder
When two structural pipes, ducts, or machine bodies interpenetrate, they meet along a closed 3D line or curve of intersection. Plotting that curve accurately ensures sheet-metal patterns fit together tightly without gaps.
Piercing Point of a Line and a Solid; Intersection of Two Planes
- Piercing Point of a Line PQ with a Solid: Pass a vertical (or edge-view) cutting plane through line
pqin the Top View (orp'q'in the Front View). Project the polygonal or curved cross-section sliced by that cutting plane out of the solid into the adjacent view; where that section outline intersectsp'q'locates the entry and exit piercing points of the line. - Intersection Line of Two Planes (ABC and PQR): Find two piercing points where edges of ABC pierce plane PQR (or vice versa) using vertical cutting planes; connecting those two piercing points gives the line of intersection common to both planes. (Alternatively, obtain an Edge View of one plane in an auxiliary view to read both edge piercing points directly.)
Core Methods for Intersections of Two Solids
- Line (Piercing-Edge / Generator) Method: Best when one solid has vertical/horizontal faces whose Edge View appears directly in one view (e.g., vertical prism or vertical cylinder seen end-on in the Top View). Identify where every lateral corner edge (prism) and critical limiting generator (outermost silhouette edges, centerline axes) of the penetrating solid pierces the vertical faces/cylinder wall in the Top View, and project those piercing heights across to the Front View.
- Cutting-Plane Method: Best for cones, pyramids, and skewed curved solids. Pass a series of parallel horizontal (or frontal) cutting planes across both solids simultaneously. Each plane cuts a simple circle or polygon from the vertical solid and a rectangle, triangle, or line pair from the penetrating solid; intersections of the two cut sections in the Top View project up to the cutting-plane line in the Front View to trace the curve.
Guide to All Seven Syllabus Solid-Pair Intersections
| Intersecting Pair | Nature of Intersection Curve | Recommended Construction Strategy |
|---|---|---|
| 1. Prism & Prism | Closed straight-line polyline (sharp corners where edges cross) | Use Line Method: mark where vertical prism edges pierce horizontal prism faces (and vice versa) in TV/SV; project vertices to FV and join straight segments across shared flat faces. |
| 2. Cylinder & Prism | Smooth planar/elliptical arcs across each flat prism face, kinking sharply at prism corners | Use Line Method (with prism faces seen as edges in TV) or Cutting Planes parallel to cylinder axis; always include prism corners as critical points where curve curvature changes abruptly. |
| 3. Cylinder & Cylinder | Smooth spatial saddle curve (reduces to two intersecting straight X-lines only when equal diameters meet perpendicularly with intersecting axes) | Use Line Method or Cutting Planes parallel to both axes: cut longitudinal elements at matching radial offsets from the common centerline in SV/TV and project to FV. |
| 4. Pyramid & Prism | Straight line segments on each triangular pyramid face, turning at pyramid slant edges | Use Horizontal Cutting Planes (cutting concentric similar polygons on pyramid and rectangles on prism) plus Vertical Edge Planes through prism edges to catch exact vertices on pyramid slant faces. |
| 5. Cone & Prism | Conic arcs (hyperbolas, parabolas, or ellipses) on each flat prism face | Use Horizontal Cutting Planes: each plane cuts a circle from the cone and parallel lines from the prism faces in TV; project intersection points up to that plane's level in FV. |
| 6. Pyramid & Cylinder | Curved arcs on each flat triangular face of the pyramid, changing direction at pyramid slant edges | Use Horizontal Cutting Planes (cutting scaled triangles/squares on pyramid and horizontal chord lines on a horizontal cylinder) plus critical planes tangent to top/bottom/axis of the cylinder and crossing pyramid slant edges. |
| 7. Cone & Cylinder | Smooth closed space curve (one continuous loop if cylinder completely penetrates, or two separate entry/exit loops if cylinder is completely engulfed) | Use Horizontal Cutting Planes (cutting circles from vertical cone and rectangular strips from horizontal cylinder in TV); always add critical planes passing through the cylinder's top, bottom, and horizontal centerline. |
Worked Examples
1
A right circular cone of base diameter 60 mm (R = 30 mm) and axis height 70 mm rests on its base on HP. It is cut by an auxiliary inclined plane passing through the midpoint of the axis (35 mm above HP) inclined at 45 degrees to HP. Calculate the slant height (L), the subtended sector angle (theta) of the full lateral surface development, and the true radial distance from the apex to the midpoint of the cut, and outline the Radial-Line Development steps.
Compute slant height and development sector angle:
- Base radius
R = 60 / 2 = 30 mm, vertical heightH = 70 mm. - True slant height
L = sqrt(R^2 + H^2) = sqrt(30^2 + 70^2) = sqrt(900 + 4900) = sqrt(5800) = 76.16 mm. - Subtended sector angle for the full cone pattern:
theta = (R / L) x 360 = (30 / 76.1577) x 360 = 141.81 degrees(~141.8 deg).
Compute cut-midpoint radial length and lay out the Radial-Line pattern:
- Draw the Top View (circle of diameter 60 mm divided into 12 equal 30-degree parts 1–12) and Front View (triangle of base 60 mm, height 70 mm), projecting all 12 generators up to the apex
o'and marking the 45-degree cutting plane passing through the axis midpoint (35 mmabove base). - Mark where the 45-degree cutting plane crosses each of the 12 projected generators (
1', 2', ..., 12') in the Front View. - Because interior generators are foreshortened in FV, project every cut point
k'horizontally onto the outer extreme slant generator (o'–1'oro'–7', which is in True Length76.16 mm) to read its true radial distanceR_kfrom apexo'! For instance, at the central axis point (h = 35 mm, half height),R_mid = 0.5 x L = 38.08 mm. - Elsewhere on the sheet, choose apex O and swing a large arc of radius L = 76.16 mm, laying off sector angle 141.81 degrees (
theta) and dividing the sector into 12 equal sub-angles (11.82 degreeseach). - Along each radial ray
O–k, mark the corresponding true radial distanceR_kmeasured from the outer slant generator above, and connect the plotted points with a smooth French curve to complete the truncated cone development.
Slant height L = 76.16 mm; full sector angle theta = 141.81 degrees; true radial distance at the 35 mm axis midpoint = 38.08 mm. Project all cut points horizontally onto the outer True-Length slant edge in FV before transferring radial distances onto the 12-ray sector.
2
A square-to-round transition piece connects a bottom 60 mm x 60 mm square duct (corners at (30, 30, 0), etc., centered at (0, 0, 0)) to a centered top 40 mm diameter circular collar (R = 20 mm, center at (0, 0, 50)), with vertical height H = 50 mm. Describe the Triangulation Method to construct its half-development, and compute the exact True Lengths of: (a) the generator from square corner (30, 30, 0) to top quadrant midpoint (0, 20, 50), (b) the generator from square corner (30, 30, 0) to the 30-degree circle point (17.32, 10.00, 50), and (c) the 30-degree chord along the top circle.
Subdivide the surface into triangles and compute True Lengths: Set the origin at the center of the 60 x 60 mm base (corners at (+/-30, +/-30, 0)), and top circle center at (0, 0, 50) with radius r = 20 mm:
- Corner
(30, 30, 0)to quadrant midpoint(0, 20, 50):- Plan projection distances are
dx = 30,dy = 30 - 20 = 10, so plan length =sqrt(30^2 + 10^2) = sqrt(1000) = 31.62 mm, and True Length =sqrt(30^2 + 10^2 + 50^2) = sqrt(3500) = 59.16 mm.
- Plan projection distances are
- Corner
(30, 30, 0)to 30-degree circle division(20 cos 30, 20 sin 30, 50) = (17.32, 10.00, 50):dx = 30 - 17.3205 = 12.6795 mm,dy = 30 - 10.00 = 20.00 mm,H = 50 mm.- True Length =
sqrt(12.6795^2 + 20^2 + 50^2) = sqrt(3060.77) = 55.32 mm.
- Top circle chord per 30-degree step (12 divisions):
Chord = 2 x r x sin(15 deg) = 40 x 0.25882 = 10.35 mm.
Graphical construction steps (True-Length Diagram + Pattern Assembly):
- Draw the Top View (60 x 60 mm square around a concentric 40 mm circle divided into 12 equal 30-degree points) and Front View (height 50 mm).
- Construct a True-Length Diagram: draw a right angle with vertical leg equal to H = 50 mm. Along the horizontal leg, step off each plan distance measured from the Top View with dividers; the hypotenuse to the 50 mm top gives each exact True Length.
- Start the half-pattern at the shortest seam line (front midpoint to top circle midpoint,
TL = sqrt(10^2 + 50^2) = 50.99 mm). Strike an arc of 30 mm (half square side) from the bottom point and 59.16 mm from the top point to complete the first half-triangle. - From the square corner, step off the 10.35 mm chord along the top and intersect with the next True Length (
55.32 mm, then symmetric55.32 mmand59.16 mmto(20, 0, 50)), repeating across two corners to finish the half-pattern.
Triangulation splits the transition piece into 4 flat triangles and 4 subdivided corner cones. Using a right-triangle True-Length Diagram with height 50 mm: corner-to-quadrant-midpoint TL = 59.16 mm, corner-to-30-deg-point TL = 55.32 mm, and 30-degree top circle chord = 10.35 mm.
3
A vertical right circular cylinder of diameter D1 = 60 mm (R1 = 30 mm) is completely penetrated at right angles by a horizontal cylinder of diameter D2 = 40 mm (R2 = 20 mm), with their axes intersecting cleanly. Describe the Cutting-Plane / Line Method to plot the curve of intersection in the Front View, and compute the exact maximum inward saddle depth of the curve along the horizontal centerline.
Compute the saddle penetration depth:
- Along the topmost and bottommost generators of the horizontal cylinder (
y = 0), the penetration touches the vertical cylinder at its central axis plane (x = 0from center, i.e.,30 mminward from the outer edge of the 60 mm cylinder). - Along the frontmost / horizontal centerline generator (
y = +/- 20 mmoffset from axis), the horizontal cylinder meets the 30 mm circle at radial distancex = sqrt(R1^2 - R2^2) = sqrt(30^2 - 20^2) = sqrt(500) = 22.36 mmfrom the vertical axis, which is30 - 22.36 = 7.64 mminward from the outermost vertical edge of the vertical cylinder.
Plot the intersection curve graphically:
- Draw the Top View (60 mm circle intersected symmetrically by the 40 mm wide horizontal cylinder), Front View (60 mm vertical rectangle crossed by the 40 mm horizontal rectangle), and Left Side View (vertical rectangle crossed by the 40 mm end-view circle of the horizontal cylinder).
- Divide the 40 mm circle in the Side View into 12 equal parts (labeled 1–12, ensuring top
1, bottom7, and front/back centerline4, 10are included as critical points). - Project each generator horizontally from the Side View into the Front View, and project its
y-offset via the 45-degree miter line into the Top View to mark where that horizontal generator pierces the 60 mm circle. - Project those piercing points vertically upward from the Top View to intersect the matching generator lines in the Front View, and trace a smooth visible saddle curve (curving inward toward the vertical axis at top/bottom and bulging outward to
7.64 mmfrom the outer edge at the centerline).
Project 12 equal divisions of the 40 mm horizontal cylinder from the Side View onto the 60 mm circle in the Top View via a 45-degree miter line, then project piercing points upward onto matching horizontal levels in the Front View. The saddle curve peaks at x = 22.36 mm from the center (7.64 mm inward from the outer edge).
Exercises
Exercises
Differentiate between developable and non-developable surfaces with two engineering examples of each, and name the exact development method used for: (a) an oblique hexagonal prism, (b) a truncated right cone, (c) a square-to-round transition duct, and (d) a spherical dome.
Developable vs. non-developable surfaces:
- Developable surfaces can be unrolled onto a flat plane without stretching, tearing, or distortion (e.g., cylinders, cones, prisms, pyramids).
- Non-developable surfaces are double-curved and cannot be laid flat exactly without plastic deformation (e.g., spheres, ellipsoids, paraboloids, tori); they require approximate strip/zone development.
Match each solid to its development method:
- (a) Oblique hexagonal prism: Parallel-Line Method (using a perpendicular right section for stretch-out widths).
- (b) Truncated right cone: Radial-Line Method (projecting cut points horizontally to the True-Length outer generator first).
- (c) Square-to-round transition duct: Triangulation Method (True-Length Diagram + sequential compass triangles).
- (d) Spherical dome: Approximate Zone (Polyconic) or Lune (Gore) Method.
Developable surfaces (prisms, pyramids, cylinders, cones) flatten without distortion; double-curved surfaces (spheres, tori) are non-developable. Methods: (a) Parallel-Line (with right section), (b) Radial-Line, (c) Triangulation, (d) Approximate Zone or Lune Method.
A right hexagonal prism (base side 25 mm, height 60 mm) and a right square pyramid (base circumradius R = 25 mm, base side 35.36 mm, vertical axis height 60 mm) are to be developed. Compute: (a) the total stretch-out length of the hexagonal prism, and (b) the true slant edge length of the square pyramid, and describe how to locate an interior cut point at height 30 mm on its development.
(a) Stretch-out length of the hexagonal prism: A regular hexagon has 6 equal sides of 25 mm each, so total lateral perimeter (stretch-out length) = 6 x 25 = 150 mm.
(b) True slant edge length and cut-point transfer for the square pyramid:
- In a right pyramid, the horizontal projection of a slant edge from apex to corner equals the circumradius
R = 25 mm, and vertical heightH = 60 mm. - True slant edge length
TL = sqrt(R^2 + H^2) = sqrt(25^2 + 60^2) = sqrt(625 + 3600) = sqrt(4225) = 65.0 mm. - To plot an interior cut point lying at 30 mm height (halfway up) in the development: project the cut point horizontally in the Front View onto the True-Length extreme slant edge, measure its radial distance from the apex (
0.5 x 65.0 = 32.5 mm), and swing that compass radius onto the corresponding radial slant edge in the development.
(a) Hexagonal prism stretch-out length = 150 mm. (b) Square pyramid true slant edge length = 65.0 mm; an interior cut point at 30 mm height transfers horizontally to the True-Length outer edge at radial distance 32.5 mm from the apex.
Explain why horizontal cutting planes are preferred over vertical cutting planes when plotting the curve of intersection between a vertical right circular cone and a horizontal cylinder, and state the visibility rule for deciding which portion of the intersection curve is solid vs. dashed.
Why horizontal cutting planes are preferred: Any horizontal plane perpendicular to the axis of a vertical right circular cone slices the cone in a perfect circle (easy to draw with a compass in the Top View!). Simultaneously, the same horizontal plane slices the horizontal cylinder along two parallel straight generator lines (a simple rectangle in the Top View). Finding where those two straight lines intersect the cone's circle in the Top View requires zero ellipses or curved approximations—and projecting those points up to the horizontal cutting-plane line in the Front View traces the curve rapidly.
Visibility rule for the intersection curve: A point on the curve of intersection is drawn solid (visible) in a given view only when it lies on the visible surface of BOTH intersecting solids in that view. If the point lies on the hidden back or bottom half of either solid, the curve segment passing through it is drawn dashed (hidden).
Horizontal cutting planes slice a vertical cone into compass-drawn circles and a horizontal cylinder into parallel straight lines in the Top View, avoiding elliptical sections. An intersection segment is solid only where it lies on the visible portion of both solids simultaneously; otherwise it is dashed.
A vertical cylinder of diameter 50 mm and height 65 mm is cut by a plane inclined at 30 degrees to HP passing through the midpoint of the axis (32.5 mm height). Compute the total stretch-out length and each of the 12 division widths, and state the minimum and maximum vertical generator heights on the lateral development if the seam is placed along the shortest generator.
Compute stretch-out width and division spacing:
- Total stretch-out length =
pi x D = 3.14159 x 50 = 157.08 mm. - Width of each of the 12 equal strips =
157.08 / 12 = 13.09 mm.
Compute minimum and maximum generator heights (30-degree cut through axis midpoint 32.5 mm):
- Over a radius of
25 mm,tan(30 deg) = 0.57735, so the cut height rises/drops by25 x 0.57735 = 14.43 mmrelative to the32.5 mmcenter height. - Minimum generator height (seam location):
32.5 - 14.43 = 18.07 mm. - Maximum generator height (center of development):
32.5 + 14.43 = 46.93 mm.
(Placing the seam at the 18.07 mm shortest generator produces a smooth symmetric bell-shaped sinusoidal wave peaking at 46.93 mm in the middle.)
Stretch-out length = 157.08 mm (12 divisions of 13.09 mm each). Placing the seam at the shortest edge gives minimum end height = 18.07 mm and maximum central peak height = 46.93 mm.
Distinguish between the shapes of intersection lines/curves produced in each of the following cases:
- Two square prisms intersecting at 90 degrees
- Two equal-diameter right circular cylinders intersecting at 90 degrees with intersecting axes
- Two unequal-diameter right circular cylinders intersecting at 90 degrees with intersecting axes
- A square prism penetrating a vertical right circular cone
Analyze the geometry of each intersection:
- Two square prisms: Flat planes intersect flat planes along straight lines, producing a closed polyline of straight segments with sharp vertices where edges of one prism pierce faces of the other.
- Equal-diameter cylinders (intersecting axes): Because every concentric distance on both circles matches at the same height, the intersection curve collapses into two straight diagonal lines forming an X in the Front View (actually two perpendicular ellipses viewed edge-on!).
- Unequal-diameter cylinders (intersecting axes): Produces a smooth continuous 3D saddle curve dipping toward the larger cylinder's axis at the top and bottom of the smaller cylinder.
- Square prism penetrating a vertical cone: Each flat face of the prism slices the cone like a section plane, producing smooth conic-section arcs (hyperbolas, parabolas, or elliptical arcs) that meet with sharp kinks at the vertical corner edges of the square prism.
- Straight-line polyline with sharp corners; 2. Two intersecting straight X-lines in the Front View (ellipses seen edge-on); 3. Smooth 3D saddle curve; 4. Conic-section arcs (hyperbolas/parabolas/ellipses) meeting sharply along the prism's corner edges.