PadhaikoAll subjects

Multi View (Orthographic) Projections

Engineering Drawing (ENME 101)

Open in the Padhaiko app

5.1 Orthographic projections

A single 2D pictorial drawing often hides rear features and distorts true lengths and angles. Multi-view (orthographic) projection solves this by projecting the 3D object onto two or more mutually perpendicular planes using parallel lines of sight perpendicular to each viewing plane, capturing exact widths, heights, and depths across aligned views.

5.1.1 First and third angle projection

Imagine enclosing the object inside an imaginary transparent glass box whose six faces form the six principal planes of projection (Front, Rear, Top, Bottom, Left Side, Right Side). Depending on which quadrant (First or Third) holds the object relative to the principal planes, two international standards arise:

AspectFirst Angle Projection (ISO / Institute of Engineering Standard)Third Angle Projection (ASME / US Standard)
Object LocationPlaced in the First Quadrant (between observer and projection plane)Placed in the Third Quadrant (projection plane lies between observer and object)
Top View (Plan)Placed directly below the Front ViewPlaced directly above the Front View
Bottom ViewPlaced directly above the Front ViewPlaced directly below the Front View
Left Side ViewPlaced to the right of the Front ViewPlaced to the left of the Front View
Right Side ViewPlaced to the left of the Front ViewPlaced to the right of the Front View
ISO Projection SymbolTruncated cone on the left, concentric circles on the rightConcentric circles on the left, truncated cone on the right
First Angle vs. Third Angle View Layout & ISO SymbolsText
FIRST ANGLE PROJECTION (Institute of Engineering Standard):          THIRD ANGLE PROJECTION (ASME):

            [Bottom View]                                   [Top View]
  [Right]   [Front View]   [Left]                [Left]    [Front View]   [Right]
            [Top View]                                      [Bottom View]

Symbol (First Angle):   [Trapezoid]  ((o))      Symbol (Third Angle):   ((o))  [Trapezoid]

5.1.2 Principal views: Methods for obtaining orthographic views, projection of lines, angles and plane surfaces, analysis in three views, projection of curved lines and surfaces, object orientation and selection of views for best representation, full and hidden lines

View Alignment and the 45-Degree Miter Line

All orthographic views are locked in strict alignment:

Analysis of Lines, Angles, and Surfaces in Three Views

Object Orientation and Selection of Views

  1. Choose the Best Front View: Orient the object in its natural working position (or stable resting orientation) so the Front View shows the longest dimension, the most characteristic contour, and the fewest hidden lines.
  2. Minimum Number of Views: Draw only as many views as needed to define the part completely without ambiguity—1 view (with DIA / thickness notes) for flat plates or turned shafts, 2 views for symmetric parts, and 3 views (FV, TV, and Left/Right SV) for asymmetric blocks.
  3. Full (Visible) and Hidden Lines: Visible outlines use Type A continuous thick lines; hidden internal edges use Type F thin dashed lines (dashes ~3–4 mm, gaps ~1 mm).
    • Hidden Line Junction Rules: Start and end a hidden line with a dash touching a visible line (never a gap) unless it is a direct continuation of a visible line, in which case leave a 1 mm gap so the transition is clear. Corners of hidden features must meet as solid L- or T-dash corners.

5.1.3 Orthographic drawings: Making an orthographic drawing, visualizing objects (Pictorial view) from the given views

Making an Orthographic Drawing from a 3D Object

  1. Select the Front View direction and projection standard (First Angle).
  2. Block in overall Width, Height, and Depth rectangles for FV, TV, and SV using light 2H construction lines, leaving uniform 20–30 mm gaps between views and drawing a 45-degree miter line for depth transfer.
  3. Lay out primary centerlines for all circles, arcs, and axes of symmetry across all views simultaneously.
  4. Draw circles and arcs first in the views where they appear circular, then project cylinder tangency boundaries to the other two views.
  5. Complete inclined faces, cutouts, slots, and hidden features by projecting every vertex across all three views.
  6. Darken outlines in proper precedence (Visible > Hidden > Centerline), erase stray construction lines, and add dimensions.

Visualizing a 3D Object from Given Views (Reading Drawings)

To reconstruct a 3D pictorial (isometric) mental picture—or find a missing third view—from two given views:

  1. Identify the bounding prism (total Width x Depth x Height).
  2. Read the primary profile in the view showing the main silhouette (e.g., L-shape, U-channel, T-block).
  3. Match adjacent closed areas in FV with corresponding regions aligned vertically in TV; trace depth extents from TV to locate front vs. back faces.
  4. Check hidden lines and centerlines to recognize through-holes, counterbores, blind pockets, or stepped ribs.
  5. Sketch a faint isometric box, carve away subtractive cutouts plane by plane, and project the 3D result to verify every edge in the missing third view.

5.1.4 Interpretation of adjacent areas, true-length lines, representation of holes, conventional practices


5.2 Sectional views: Full, half, offset, broken (Partial), rotated/aligned, revolved, removed (Detail) sections, phantom of hidden section, specifying cutting planes for sections, convention practices

When a part contains intricate internal bores, stepped chambers, or threaded passages, overlapping dashed hidden lines quickly become unreadable. Sectional views slice open the object along an imaginary cutting plane, remove the near half, and show the exposed interior edges as solid visible lines while marking cut solid material with section lining (hatching).

Specifying Cutting Planes and Hatching Rules

Types of Sectional Views

Classification of Sectional Views (ISO 128-40 / BIS SP 46)
Section TypeCutting Plane Path & CoverageBest Used For
Full SectionStraight cutting plane cuts completely through the entire object along a centerline or offset axisGeneral hollow castings, housings, bushings, valves with internal passages
Half SectionTwo perpendicular cutting planes meet at the centerline, removing one-quarter of a symmetrical part; one half of the view shows the cut interior, the other half shows the exteriorSymmetrical cylindrical parts (pulleys, flanged couplings, wheels); omit hidden lines on the unsectioned half unless needed for clarity
Offset SectionCutting plane steps at 90-degree bends to pass through multiple features lying in different parallel planesParts with staggered holes, slots, and bosses not aligned on a single straight line (90-degree step bends are NOT drawn as lines in the section view)
Broken-out (Partial) SectionIrregular freehand short break line (Type C) tears away only a small local portion to expose an internal keyway, blind hole, or pinParts needing only a localized interior check without drawing a full or half section
Rotated / Aligned SectionBent or angled cutting plane swings an inclined arm, rib, or hole into alignment with the main projection planeOdd-numbered flanges, angled arms, handwheel spokes, and radial ribs
Revolved SectionCutting plane passes perpendicular to the axis of a bar, spoke, or arm, and the cross-section is revolved 90 degrees in place directly onto the viewChecking cross-sectional profiles (I-beam, T-rib, oval spoke) along long members
Removed (Detail) SectionCross-section is pulled completely outside the main view (aligned along the cutting-plane centerline or placed elsewhere on the sheet with label SECTION A-A)Crowded drawings or enlarged detail cross-sections (SCALE 2:1) of stepped shafts and keyways
Phantom (Hidden) SectionHatching drawn with dashed lines directly over an un-cut exterior outline (no material removed)Rarely used; shows interior wall thickness behind a thin outer shell in a single view

Sectioning Conventional Practices (Elements Never Hatched)

Even when a cutting plane slices lengthwise right through them, the following standard components and thin structural elements are NOT hatched so the drawing does not look falsely solid or confusing:


5.3 Auxiliary views: Basic concept and use, drawing methods and types, symmetrical and unilateral auxiliary views, auxiliary sectional views

Standard Front, Top, and Side views distort any inclined or oblique surface because the line of sight is not perpendicular to that face. An Auxiliary View projects the object onto a supplementary plane placed parallel to the inclined face (perpendicular to its edge view), revealing the true shape, true hole circularity, and true angles of that surface.

Drawing Methods and Types of Auxiliary Views

  1. Classification by Viewing Direction (Primary Auxiliary Views):
    • Elevation (Height) Auxiliary View: Projected from the Top View onto a plane perpendicular to HP (measures heights Z from the Front View).
    • Plan (Width) Auxiliary View: Projected from the Front View onto a plane perpendicular to VP (measures depths Y from the Top View).
    • Profile (Depth) Auxiliary View: Projected from the Side View onto a plane perpendicular to PP (measures widths X from the Front/Top View).
  2. Primary vs. Secondary Auxiliary Views:
    • Primary Auxiliary View: Projected from one of the three principal views onto a plane perpendicular to one principal plane; recovers true shape of an inclined surface.
    • Secondary Auxiliary View: Projected from a primary auxiliary view onto a plane perpendicular to it; recovers true shape of an oblique surface (inclined to all three principal planes).

Symmetrical, Unilateral, Bilateral, and Auxiliary Sectional Views

Definition

Reference-Plane Variants and Auxiliary Sections

  1. Symmetrical (Bilateral) Auxiliary View: Uses a centerline (axis of symmetry) as the reference plane (RP) instead of an edge. Feature half-widths are transferred symmetrically on both sides of the auxiliary centerline—ideal for symmetric inclined lugs, brackets, and flanges.
  2. Unilateral Auxiliary View: Uses an outer flat face (e.g., the back face or front datum face) as the reference plane (RP), transferring all depth/width measurements on one side only of the reference line—ideal for asymmetric slanted brackets.
  3. Partial Auxiliary View: Draws only the inclined feature (plus a short break line) rather than projecting the entire distorted remainder of the body—saving time and eliminating unreadable elliptical projections in principal views.
  4. Auxiliary Sectional View: Combines an auxiliary view with a cutting plane parallel to an inclined flange or boss (SECTION A-A). The view shows both the true shape of the inclined surface and the hatched internal cross-section perpendicular to that inclined axis.

Worked Examples

Example 1

1

Describe the exact step-by-step procedure to draw three orthographic views (Front View, Top View, and Left Side View) in First Angle Projection for a stepped L-bracket having overall dimensions Width = 80 mm, Depth = 50 mm, Height = 40 mm, a 15 mm thick horizontal base carrying a centered 20 mm diameter through-hole, and a 50 mm wide x 40 mm tall vertical back-wall (leaving a 30 mm long x 25 mm tall stepped front cutout). Also verify the solid volume of the bracket.

Verify the bracket volume for geometric sanity:

  • Total bounding block = 80 x 50 x 40 = 160000 cu mm.
  • Upper front cutout = 30 x 50 x 25 = 37500 cu mm.
  • Centered 20 mm diameter (R = 10 mm) through-hole across the 15 mm thick base = pi x 10^2 x 15 = 4712.39 cu mm.
  • Net solid volume = 160000 - 37500 - 4712.39 = 117787.61 cu mm.

Set up First Angle view layout:

  • Place Front View (FV) in the upper-left area (80 mm wide x 40 mm high), showing the L-profile.
  • Place Top View (TV) directly below FV (80 mm wide x 50 mm deep), leaving a 25 mm vertical gap.
  • Place Left Side View (LSV) directly to the right of FV (50 mm deep x 40 mm high), leaving a 25 mm horizontal gap, and draw a 45-degree miter line from the bottom-right corner of the FV-TV gap box.

Project features across all three views:

  1. L-profile in FV: Draw the 80 mm horizontal bottom, 40 mm left vertical wall, 50 mm top horizontal edge, 25 mm step drop down to the 15 mm base height, and 30 mm horizontal ledge to the right edge.
  2. Project down to TV: Project the 80 mm outer bounds and the 50 mm step-drop line vertically down into the 80 x 50 mm TV rectangle. Locate the 20 mm diameter through-hole centered on the 30 mm base ledge (15 mm from the right edge, 25 mm from front/back) and draw it as a 20 mm solid circle with intersecting Type G centerlines.
  3. Transfer depth to LSV via miter line: Project the 15 mm base thickness and 40 mm top horizontally from FV, and project the 50 mm depth from TV across the 45-degree miter line upward into LSV. Draw the 20 mm hole as two vertical dashed hidden lines spaced 10 mm on each side of the centerline through the 15 mm base in both FV and LSV.
Answer:

In First Angle Projection, draw the L-profile Front View (80 x 40 mm) top-left, the Top View (80 x 50 mm) directly below it (showing the 20 mm hole as a full circle), and the Left Side View (50 x 40 mm) to the right of FV via a 45-degree miter line (showing the hole with vertical hidden lines). Net solid volume = 117787.61 cu mm.

Example 2

2

Explain the step-by-step Visualization and Miter-Line Method to construct the missing Left Side View in First Angle Projection when given a Front View (width 70 mm, height 45 mm, showing an inverted U-channel with a top beveled corner) and a Top View (width 70 mm, depth 40 mm, showing a rectangular through-slot and full-depth bevel edge).

Establish the bounding box and 45-degree miter line:

  1. Extend horizontal construction lines rightward from the top (45 mm) and bottom (0 mm) of the Front View.
  2. Draw a 45-degree miter line down-right from the intersection of the FV-TV gap borders (25 mm right of FV, 25 mm below FV).
  3. Project the front and back horizontal edges (40 mm depth) of the Top View rightward to the miter line and turn vertically upward into the Side View zone, forming a 40 mm wide x 45 mm high bounding rectangle.

Project every horizontal and depth feature and determine visibility:

  1. Project the height of the inverted U-channel ceiling (e.g., 20 mm from bottom) horizontally from FV across the 40 mm Side View width. Because the U-channel runs straight through from front to back (confirmed by full-depth dashed hidden lines in the Top View), it projects as a dashed hidden horizontal line across the Side View behind the solid side wall.
  2. Project the top beveled slope vertices: the bevel's start height in FV projects horizontally across SV; check TV to see if the bevel spans the full 40 mm depth (making a flat horizontal visible line across SV) or only half the depth (forming a stepped region).
  3. Project the rectangular through-slot boundaries from TV via the miter line upward into SV as vertical hidden (or visible) lines depending on whether they lie behind the solid wall or open on the left face.
Answer:

Project all heights horizontally from the Front View and all depths from the Top View across a 45-degree miter line, then match adjacent enclosed areas between FV and TV to verify whether each projected line across the Side View is a solid visible edge or a dashed hidden edge.

Example 3

3

A 50 mm x 40 mm rectangular flange on a bracket is inclined at 30 degrees to the Horizontal Plane (appearing foreshortened in the Top View and as an edge in the Front View), and contains a centered 20 mm diameter hole. Compute its foreshortened width in the Top View, and describe the steps to draw a Primary Auxiliary View showing the true shape of the inclined flange and circular hole.

Compute the foreshortened projection in the Top View: In the Front View, the 50 mm inclined flange appears in True Length tilted at 30 degrees to horizontal. Projecting vertically down to the Top View foreshortens its 50 mm edge to:

  • Projected horizontal span = 50 x cos(30 deg) = 50 x 0.8660 = 43.30 mm (so the Top View shows a 43.30 mm x 40 mm rectangle, and the 20 mm circular hole distorts into an ellipse of major axis 20 mm and minor axis 20 x cos(30 deg) = 17.32 mm).
  • Vertical rise of the flange in Front View = 50 x sin(30 deg) = 25.00 mm.

Construct the Primary Auxiliary View (Unilateral or Symmetrical):

  1. Draw an auxiliary reference line (RP / X1Y1) parallel to the inclined edge view of the flange in the Front View, placed cleanly outside the bracket.
  2. Draw a centerline (RP) for the flange in the auxiliary zone parallel to the inclined edge view (for a Symmetrical Auxiliary View), leaving a 20–25 mm gap from the Front View.
  3. Project perpendicular lines (at 60 degrees to horizontal, i.e., 90 degrees to the 30-degree inclined face) from the flange ends, hole center, and hole edges in the Front View into the auxiliary view.
  4. Measure the true 40 mm depth (or +/- 20 mm half-widths from the centerline in the Top View) and transfer them perpendicularly across the auxiliary centerline.
  5. Draw the true 50 mm x 40 mm rectangle and use a compass (R = 10 mm) to draw the true 20 mm circle centered on the auxiliary axes, adding a short break line if making a Partial Auxiliary View.
Answer:

In the Top View, the 50 mm face foreshortens to 43.30 mm (50 cos 30 deg) and the 20 mm hole becomes a 20 x 17.32 mm ellipse. Projecting perpendicular to the Front View's edge view and transferring +/- 20 mm half-widths from the Top View produces a Symmetrical Primary Auxiliary View showing the true 50 x 40 mm flange and true 20 mm diameter circle.


Exercises

Exercises

Question 1

Compare First Angle Projection and Third Angle Projection with respect to: (a) quadrant and observer-object-plane sequence, (b) positions of Top, Left Side, and Right Side views relative to the Front View, and (c) the standard ISO projection symbol. Which system is used in Institute of Engineering / Nepal?

Compare quadrant and viewing sequence:

  • First Angle Projection: Object is in Quadrant I (Observer -> Object -> Projection Plane). The object sits between the eye and the plane, so shadows project away from the viewer.
  • Third Angle Projection: Object is in Quadrant III (Observer -> Projection Plane -> Object). The transparent plane sits between the eye and the object.

Compare view positions and ISO symbols:

  • First Angle (Institute of Engineering / ISO standard): Top View sits below FV; Left Side View sits to the right of FV; Right Side View sits to the left of FV. Symbol shows the truncated cone on the left and concentric circles on the right.
  • Third Angle (ASME standard): Top View sits above FV; Left Side View sits to the left of FV; Right Side View sits to the right of FV. Symbol shows concentric circles on the left and truncated cone on the right.
Answer:

In First Angle (used by Institute of Engineering), the object sits between observer and plane: Top View is below FV, Left Side View is to the right of FV, and the ISO symbol places the truncated cone on the left. In Third Angle, the plane sits between observer and object: Top View is above FV and each side view sits on its own named side.

Question 2

State the three rules of hidden-line junctions when drawing orthographic views, explain what adjacent enclosed areas separated by a visible line signify, and list the criteria used to choose the best Front View of an object.

Hidden-line junction rules:

  1. A hidden line starts and ends with a dash touching the intersecting visible outline (forming a closed corner or T-junction), rather than leaving a gap.
  2. Exception: when a hidden line is a direct collinear continuation of a visible line, leave a clear 1 mm gap at the transition point so the reader sees where the visible edge ends.
  3. Corners where two hidden lines meet must intersect with solid dashes forming an L-corner (not open gaps), and crossing hidden lines should touch or cross cleanly.

Adjacent areas and Front View selection:

  • Adjacent enclosed areas: Two touching regions separated by a visible line in an orthographic view cannot lie in the same plane—they indicate a change in depth (step), an inclined bend, or a curved surface intersection.
  • Best Front View criteria: Choose the orientation showing the longest overall dimension, the most informative shape/contour, natural working stability, and the minimum number of hidden lines.
Answer:

Hidden lines touch intersecting visible lines with dashes (except a 1 mm gap when collinear) and meet at solid dash corners. Adjacent separated areas represent planes at different depths, angles, or curvatures. Select the Front View showing the longest length, clearest profile, and fewest hidden lines.

Question 3

Distinguish among (a) Half Section, (b) Offset Section, (c) Revolved Section, and (d) Removed Section, and list four engineering elements that are never hatched even when sliced longitudinally by a cutting plane.

Distinguish the four sectional view types:

  • (a) Half Section: Two cutting planes meet at 90 degrees on a centerline to remove one-quarter of a symmetrical part, showing interior hatched detail on one half and exterior shape on the other half.
  • (b) Offset Section: A stepped cutting plane bends at 90 degrees to pass through staggered holes or features on different parallel planes (bends are omitted in the section view).
  • (c) Revolved Section: A transverse cross-section is cut perpendicular to a long bar, spoke, or rib and rotated 90 degrees in place directly onto the main view.
  • (d) Removed Section: A cross-section is drawn completely outside the main view (aligned with the cutting plane or placed elsewhere with a label such as SECTION A-A, often at an enlarged scale).

Elements NOT hatched when cut longitudinally:

  1. Solid shafts, axles, and spindles
  2. Fasteners (bolts, nuts, screws, studs, rivets, washers, pins, keys)
  3. Thin ribs, webs, and gussets cut parallel to their flat faces
  4. Spokes of pulleys/handwheels and gear teeth (and ball/roller bearings)
Answer:

Half sections cut one-quarter of symmetric parts; offset sections step across staggered features; revolved sections turn 90 degrees in place; removed sections sit outside the main view. Never hatch longitudinal cuts through shafts, bolts/nuts/keys/pins, thin ribs/webs, or spokes/bearings.

Question 4

What is an Auxiliary View and when is it required? Differentiate between a Symmetrical Auxiliary View and a Unilateral Auxiliary View, and compute the foreshortened horizontal and vertical projections of a 60 mm inclined face tilted at 45 degrees to the horizontal.

Purpose of Auxiliary Views and Reference Variants: An Auxiliary View projects onto a plane parallel to an inclined (or oblique) surface so its true shape, true lengths, true angles, and circular holes appear without foreshortening.

  • Symmetrical Auxiliary View: Uses the centerline of a symmetric part as the reference plane (RP), transferring equal half-depths/half-widths to both sides of RP.
  • Unilateral Auxiliary View: Uses one outer datum face (such as the back edge) as RP, transferring all depth/width dimensions to one side only—suited to asymmetric features.

Compute foreshortened projections of a 60 mm face tilted at 45 degrees:

  • Horizontal projection (seen in Top View) = 60 x cos(45 deg) = 60 x 0.7071 = 42.43 mm.
  • Vertical projection (seen in Side View) = 60 x sin(45 deg) = 60 x 0.7071 = 42.43 mm.

Only the Primary Auxiliary View drawn perpendicular to the 45-degree edge shows the true 60 mm length.

Answer:

An auxiliary view reveals the true shape of an inclined or oblique surface. Symmetrical auxiliary views measure to both sides of a centerline, whereas unilateral auxiliary views measure to one side of an outer datum plane. At 45 degrees, a 60 mm face foreshortens to 42.43 mm in both Top and Side views.

Question 5

Explain how drilled through-holes, blind holes, counterbored holes, and countersunk holes are represented in orthographic front and top views, and explain how aligned ribs/lugs are handled under conventional drafting practice.

Standard hole representations:

  • Drilled Through-Hole: Circle in Top View; two vertical hidden (or visible if sectioned) lines spanning the entire wall thickness in Front View.
  • Blind Drilled Hole: Circle in Top View; vertical parallel lines ending internally in a 120-degree (approx. 118-degree) V-shaped conical drill tip at the specified cylindrical depth.
  • Counterbored Hole: Two concentric circles in Top View; stepped wider flat-bottomed cylindrical recess above the smaller through-hole in Front View.
  • Countersunk Hole: Two concentric circles in Top View; conical 82-degree or 90-degree V-flared bevel opening into the smaller hole in Front View.

Conventional practice for aligned ribs, lugs, and holes: When a circular flange has an odd number of evenly spaced holes (e.g., 3 or 5) or angled ribs/spokes that do not lie directly on the vertical cutting plane, rotate them conceptually around the central axis onto the vertical plane before projecting the section or elevation. This avoids misleading foreshortening and shows true radial spacing clearly.

Answer:

Through-holes run full thickness; blind holes end in a 120-degree conical drill point; counterbores show a flat-bottomed cylindrical step; countersinks show a conical V-flare. Odd-numbered ribs, lugs, and bolt holes are conceptually rotated into the cutting/projection plane (aligned convention) to display true radial geometry.

← Basic Descriptive GeometryDevelopments and Intersections →