Thread Cutting
Open in the Padhaiko app3.1 Classification of threads
A screw thread is a continuous helical ridge of uniform cross-section formed on the outside or inside surface of a cylinder or cone. Threads serve two broad engineering roles: fastening (bolts, nuts, studs, screws) and power/motion transmission (lathe leadscrews, vice screws, screw jacks).
Fundamental Screw Thread Nomenclature
- Major Diameter (D or d): Largest diameter of an external or internal thread (nominal size of the bolt/nut, e.g., 10 mm for an M10 thread).
- Minor (Core/Root) Diameter (Dc or d1): Smallest diameter of the thread, measured across the roots of an external thread or crests of an internal thread.
- Pitch Diameter (Effective Diameter): Imaginary cylindrical diameter where the width of the thread ridge equals the width of the groove space.
- Pitch (p): Axial distance measured parallel to the axis from a point on one thread tooth to the corresponding point on the adjacent tooth.
- Lead (L): Axial distance a nut or screw advances in one complete revolution (360 degrees). For a single-start thread, Lead = Pitch; for a multi-start thread with n starts, Lead = n x Pitch.
- Crest, Root, and Flank: The crest is the outermost edge of the ridge, the root is the bottom of the groove, and the flank is the inclined side connecting crest to root.
- Thread Angle: Included angle between adjacent flanks measured in an axial plane (for example, 60 degrees for ISO Metric threads).
Ways of Classifying Screw Threads
- By Surface Location:
- External (Male) Thread: Cut on the outside surface of a rod, bolt, or pipe.
- Internal (Female) Thread: Cut inside a cylindrical hole, nut, or boss.
- By Hand of Helix:
- Right-Hand (RH) Thread: Standard thread that advances away from the viewer when turned clockwise (tightens clockwise).
- Left-Hand (LH) Thread: Advances away when turned counter-clockwise. Used where machine rotation would loosen a standard RH nut (e.g., left-side bicycle pedal, left grinding-wheel arbor nut, turnbuckles, and flammable-gas cylinder valves like acetylene).
- By Number of Starts:
- Single-Start Thread: One continuous helical groove; Lead = Pitch. Provides high friction/self-locking grip for fasteners.
- Multi-Start Thread (Double, Triple): Two or more parallel helical grooves equally spaced around the circumference; Lead = n x Pitch. Provides rapid axial travel (e.g., bottle caps, fly-press screws, quick-acting valves).
- By Pitch Series (Coarse vs. Fine):
- Coarse Thread (e.g., M10 x 1.5): Larger pitch, deeper teeth, faster assembly, resists stripping in softer materials.
- Fine Thread (e.g., M10 x 1.0): Smaller pitch, shallower groove, larger core diameter (stronger in tension), resists loosening under vibration, suited to thin-walled tubing.
- By Thread Profile (Cross-Sectional Form):
| Thread Profile | Thread Angle | Crest / Root Shape | Key Applications |
|---|---|---|---|
| ISO Metric (M) | 60 degrees | Flat crest, rounded root | Universal metric fasteners, machine assembly, general workshop |
| Unified (UNC / UNF) | 60 degrees | Flat or rounded crest/root | Inch-series industrial fasteners (coarse and fine) |
| BSW (Whitworth) | 55 degrees | Rounded crests and roots | Older British machinery, pipe fittings (BSP variant) |
| BA (British Assoc.) | 47.5 degrees | Rounded crests and roots | Small instrument screws and electrical terminals |
| Square Thread | 90 deg flanks (0 deg included) | Flat square crest and root | Screw jacks, bench vice screws, heavy power transmission (zero radial bursting thrust) |
| Acme Thread | 29 degrees | Flat crest and root | Lathe leadscrews (allows easy engagement/disengagement of split half-nuts) |
| Buttress Thread | 45 deg / 7 deg (asymmetric) | Flat crest and root | Heavy axial thrust in one direction only (quick-acting vices, artillery breeches) |
| Knuckle Thread | Rounded waves | Semicircular crest and root | Railway couplings, glass bottle necks, dirty/rough environments |
3.2 Thread cutting tools for hand threading
Manual thread cutting in a fitting shop uses two primary cutting tools—taps (for internal threads) and dies (for external threads)—along with holding wrenches, layout/checking tools, and cutting lubricants:
- Hand Taps and Tap Wrenches:
- Solid / Double-Ended Tap Wrench: Fixed or stepped square openings for common tap sizes; gives balanced two-hand torque.
- Adjustable Bar Tap Wrench: Central V-jaw chuck tightened by knurled handle; fits a wide range of medium and large taps cleanly.
- T-Handle Tap Wrench: Short sliding T-bar chuck ideal for small taps (M3–M6) or deep/confined pockets where a long bar hits obstructions.
- Threading Dies and Die Stocks (Die Holders):
- A die stock holds a circular die rigidly using locating set screws: a central screw engages the die's V-notch to expand a split die, while two side screws clamp and compress it inside the stock recess.
- Supporting Preparation and Inspection Tools:
- Twist Drills and Countersink: Drill the exact tap drill hole and chamfer the mouth before tapping.
- Try Square: Checks that the tap enters strictly perpendicular (90 degrees) to the workpiece face.
- Screw Pitch Gauge: Leaf gauge with serrated blades stamped by pitch (mm or TPI) to identify unknown threads.
- Cutting Fluids: Reduce friction, cool cutting edges, and produce smooth, tear-free threads—cutting oil / lard oil for mild steel, kerosene or soluble oil for aluminium, and dry cutting for cast iron and brass (oil mixes with cast-iron dust into an abrasive paste).
3.3 Threading taps: Types, uses and care
A threading tap is a hardened high-speed steel (HSS) or carbon-steel cylindrical cutter with external threads interrupted by 3 or 4 axial flutes (providing cutting edges and chip clearance) and a square-ended shank for the tap wrench.
Types of Hand Taps (Standard 3-Tap Set)
Hand taps are normally supplied in a matched set of three taps with identical nominal diameter and pitch, differing only in the length of their chamfered lead at the tip:
| Tap Type | Chamfer Lead Length | Tip Appearance | Specific Purpose & Use |
|---|---|---|---|
| 1. Taper (First / Roughing) Tap | 6 to 8 threads tapered (~4 deg per side) | Long pointed taper at end | Starts the thread smoothly, aligns easily square to the hole, and cuts roughly 60% of the metal gradually; passes all the way through through holes |
| 2. Second (Intermediate / Plug) Tap | 3 to 4 threads tapered (~8–10 deg) | Moderate chamfer | Follows the taper tap to cut threads to full depth in through holes or deeper into blind holes |
| 3. Bottoming (Third / Finisher) Tap | 1 to 1.5 threads tapered (~20 deg) | Almost flat square end | Follows the second tap to form full-depth threads right down to the flat bottom of a blind hole |
Tap Drill Size (TDS)
Before tapping an internal thread, a hole smaller than the nominal major diameter must be drilled so enough metal remains to form the thread ridges without overloading the tap.
Tap Drill Size Formulas (ISO Metric Threads)
For an ISO Metric 60-degree thread of nominal major diameter D (mm) and pitch p (mm):
- Theoretical Minor Diameter (100% thread depth): D_minor = D - 1.0825 x p (Drilling to 100% depth makes tapping unnecessarily stiff and prone to tap breakage.)
- Standard Workshop Rule (approx. 75–80% thread depth): TDS = D - p (Or more precisely for 75% engagement: TDS = D - 0.974 x p, rounded to the nearest standard 0.1 mm or 0.5 mm drill size.)
Care of Threading Taps
- Always check squareness with a try square during the first 2–3 turns—tilting a tap bends and snaps it inside the hole.
- Back off regularly: Every half to one full turn forward, reverse 1/4 to 1/2 turn until you hear or feel the metal chip snap clean. Continuous forward turning packs chips in the flutes and jams/breaks the tap.
- Never force a stuck tap: If resistance spikes, reverse the tap out, blow or brush out chips (especially at the bottom of blind holes), add cutting oil, and restart gently.
- Use both hands evenly: Apply purely rotational torque with equal force on both wrench handles—never bend sideways.
- Storage: Wipe clean and oil lightly after use; store in slotted wooden racks so brittle cutting edges do not knock together.
3.4 Threading dies: Types, uses and care
A threading die is a hardened tool-steel nut-like cutter with internal threads intersected by chip-clearance holes (flutes) and a chamfered starting throat on one face.
Types of Threading Dies
- Solid Circular Die: One-piece ring without any adjustment slot; cuts threads to a fixed pitch diameter. Rigid and accurate for finishing passes or small sizes, but cannot compensate for wear or split the cut across passes.
- Split Circular Button Die: Has a radial slit cut through one side and a V-notch on the outer rim. Adjusting the three screws in the die stock slightly expands the die for an easier first cut and closes it back to exact nominal size for the final pass.
- Two-Piece Adjustable Die: Two separate rectangular/chaser halves mounted in a heavy collet guide and tightened progressively by set screws; used for larger rod diameters (M16 and above).
- Hexagonal Die Nut: A hardened hexagonal block resembling a standard nut with flutes, turned by an ordinary spanner. Designed only for cleaning/re-chasing bruised or rusty threads, never for cutting fresh threads on unthreaded rod.
Care of Threading Dies
- Undersize Blank Rule: Before cutting an external thread of nominal diameter D and pitch p, prepare the rod slightly undersize by roughly 0.1 x p (i.e., Blank diameter D_b = D - 0.1p, typically 0.1–0.2 mm smaller than D) so crest metal squeezing upward does not bind inside the die.
- Chamfer the Rod End: File or turn a 45-degree chamfer slightly smaller than the minor diameter at the rod tip so the die catches squarely without cross-threading.
- Correct Face Orientation: Always place the chamfered throat side (usually the stamped size side) facing down toward the rod end when starting.
- Reverse to Break Chips & Lubricate: Turn 1/2 turn forward, 1/2 turn back, and brush swarf out of the clearance holes frequently with cutting oil.
3.5 Thread cutting by hand: Cutting internal and external thread
| Aspect | Internal Threading (Tapping) | External Threading (Dieing) |
|---|---|---|
| Cutting Tool | 3-piece hand tap set (Taper -> Second -> Bottoming) | Split circular button die or two-piece die in die stock |
| Workpiece Prep | Drill TDS = D - p; lightly countersink hole mouth | Turn/file blank to D - 0.1p; chamfer rod end 45 degrees |
| Starting Alignment | Check tap perpendicularity in two 90-degree planes with try square | Hold die stock strictly horizontal; press chamfered side of die squarely onto chamfered rod end |
| Chip Breaking | 1/2 to 1 turn forward, then 1/2 turn backward | 1/2 turn forward, then 1/2 turn backward |
| Sizing / Multi-Pass | Progress through Taper -> Second -> Bottoming tap | Expand split die for first pass; close screw slightly and re-run for clean final fit |
Procedure for Cutting an Internal Thread (Hand Tapping)
- Clamp the workpiece firmly in a bench vice with the hole axis vertical.
- Drill the calculated tap drill hole (TDS = D - p) to the required depth (for blind holes, drill 3–5 mm deeper than the usable thread length if design allows) and lightly countersink the top rim to ease tap entry and prevent raised burrs.
- Clamp the taper (first) tap in a suitable tap wrench and coat the flutes with cutting oil (for steel).
- Set the tap tip vertically into the hole, apply gentle downward pressure while turning clockwise 1–2 revolutions until the first threads bite, then verify squareness from two perpendicular directions using a try square. Adjust immediately if tilted before going deeper.
- Continue turning clockwise 1/2 to 1 turn, then reverse 1/2 turn counter-clockwise to break and clear chips.
- For a through hole, run the taper tap all the way through (or follow with the second tap). For a blind hole, remove the taper tap, clear all chips from the hole bottom, run the second tap carefully until it touches the bottom, clear chips again, and finish with the bottoming tap.
- Test the finished thread with a matching bolt.
Procedure for Cutting an External Thread (Hand Dieing)
- Prepare the cylindrical rod slightly undersize (D_b = D - 0.1p) and file a 45-degree chamfer at the starting end.
- Clamp the rod vertically in a bench vice using soft jaws (if finished) so only the threaded length plus ~15 mm protrudes above the jaws.
- Open the split button die slightly with the center adjusting screw inside the die stock, ensuring the chamfered starting face points downward.
- Place the die squarely over the chamfered rod tip, press downward evenly with both palms on the die stock handles, and turn clockwise 1–2 revolutions until the die catches cleanly. Check visually that the die stock stays horizontal (perpendicular to the rod axis).
- Apply cutting oil and advance 1/2 turn forward, then 1/2 turn back to break chips, repeating down to the shoulder/required thread length.
- Unscrew the die counter-clockwise, brush chips out, tighten the side screws slightly to bring the split die to exact nominal size, and run a smooth finishing pass.
- Test-fit a standard nut of the same size onto the cut thread—it should spin smoothly by hand without wobble or binding.
Worked Examples
1
Determine the tap drill size (TDS) (using both the standard workshop rule and the theoretical 100% minor diameter) and the external blank rod diameter required to cut: (a) M10 x 1.5 threads, and (b) M12 x 1.75 threads.
(a) Calculations for M10 x 1.5 (D = 10 mm, p = 1.5 mm):
- Workshop Tap Drill Size: TDS = D - p = 10 - 1.5 = 8.5 mm (standard 8.5 mm twist drill).
- Theoretical Minor Diameter (100%): D_minor = 10 - (1.0825 x 1.5) = 10 - 1.6238 = 8.38 mm.
- External Blank Diameter: D_b = D - 0.1p = 10 - (0.1 x 1.5) = 10 - 0.15 = 9.85 mm.
(b) Calculations for M12 x 1.75 (D = 12 mm, p = 1.75 mm):
- Workshop Tap Drill Size: TDS = D - p = 12 - 1.75 = 10.25 mm (nearest standard metric drill: 10.2 mm or 10.25 mm).
- Theoretical Minor Diameter (100%): D_minor = 12 - (1.0825 x 1.75) = 12 - 1.8944 = 10.11 mm.
- External Blank Diameter: D_b = D - 0.1p = 12 - (0.1 x 1.75) = 12 - 0.175 = 11.825 mm (approx. 11.8 mm).
(a) M10 x 1.5: TDS = 8.5 mm (theoretical minor = 8.38 mm); external blank diameter = 9.85 mm. (b) M12 x 1.75: TDS = 10.25 mm (10.2 mm drill); external blank diameter = 11.83 mm (11.8 mm).
2
(a) A triple-start (3-start) square thread on a fly-press screw has a pitch of 4 mm. Calculate its lead and the number of full revolutions required to raise the ram by 60 mm. (b) How many full turns of the tap wrench are needed to thread an M10 x 1.5 single-start blind hole to a full-thread depth of 24 mm?
(a) Triple-start thread lead and revolutions:
- Number of starts n = 3; Pitch p = 4 mm.
- Lead L = n x p = 3 x 4 = 12 mm per revolution.
- Number of revolutions for 60 mm travel = Total travel / Lead = 60 / 12 = 5 revolutions.
(b) Turns required for M10 x 1.5 single-start hole:
- For a single-start thread (n = 1), Lead = Pitch = 1.5 mm per revolution.
- Number of full turns to advance 24 mm = 24 / 1.5 = 16 full turns (plus backing off 1/2 turn after every 1/2–1 turn forward to break chips, and running Taper, Second, and Bottoming taps in sequence).
(a) Lead = 12 mm, revolutions for 60 mm travel = 5 revolutions; (b) 16 full turns are needed to advance 24 mm at 1.5 mm pitch.
3
A student must cut an M8 x 1.25 internal thread inside a 20 mm deep blind hole in a mild steel block. List the exact tools required and describe the complete step-by-step threading sequence, noting how tap breakage and bottoming errors are prevented.
Select tools and prepare the blind hole:
- Tools needed: 6.8 mm twist drill (TDS = 8 - 1.25 = 6.75 mm -> nearest standard drill 6.8 mm), countersink bit, bench vice, M8 x 1.25 three-tap set (Taper, Second, Bottoming), adjustable or T-handle tap wrench, try square, depth gauge, cutting oil, and chip brush/air blower.
- Drill the 6.8 mm hole to 24 mm depth (leaving 4 mm chip/lead clearance below the 20 mm thread) and lightly countersink the rim. Clear all drilling chips from the hole.
Start and advance the Taper, Second, and Bottoming taps:
- Clamp the block flat in the bench vice. Coat the Taper (first) tap with cutting oil, set it vertically into the hole, and turn clockwise 1.5 turns.
- Check perpendicularity from two sides 90 degrees apart using a try square; correct tilt gently before deeper cutting.
- Advance 1/2 turn forward and reverse 1/2 turn backward to snap chips cleanly until the tap tip lightly touches the hole bottom (marked with a depth tape flag at 24 mm on the shank).
- Back out the taper tap completely and shake/blow out all chips trapped at the bottom of the blind hole.
- Repeat the forward-and-reverse cutting cycle with the Second tap, clear chips again, and finish down to the bottom using the Bottoming tap (feeling the bottom gently—never forcing rotation once it touches the hole base).
- Unscrew, clean the hole, and verify fit with an M8 x 1.25 bolt.
Drill a 6.8 mm hole (TDS = 8 - 1.25 = 6.75 mm) slightly deeper than 20 mm, countersink, start vertically with the Taper tap checked by a try square, reverse 1/2 turn per 1/2–1 turn forward with cutting oil, clear bottom chips between stages, and finish sequentially with the Second and Bottoming taps without forcing at the hole base.
Exercises
added
Calculate the workshop tap drill size (TDS = D - p) and external blank rod diameter (D_b = D - 0.1p) for: (a) M16 x 2.0 coarse metric thread (also compute the theoretical 100% minor diameter), and (b) M6 x 1.0 coarse metric thread.
(a) For M16 x 2.0 (D = 16 mm, p = 2.0 mm):
- Workshop Tap Drill Size: TDS = 16 - 2.0 = 14.0 mm.
- Theoretical minor diameter (100% depth): D_minor = 16 - (1.0825 x 2.0) = 16 - 2.165 = 13.835 mm (approx. 13.84 mm).
- External blank diameter: D_b = 16 - (0.1 x 2.0) = 16 - 0.20 = 15.80 mm.
(b) For M6 x 1.0 (D = 6 mm, p = 1.0 mm):
- Workshop Tap Drill Size: TDS = 6 - 1.0 = 5.0 mm.
- External blank diameter: D_b = 6 - (0.1 x 1.0) = 6 - 0.10 = 5.90 mm.
(a) M16 x 2.0: TDS = 14.0 mm (theoretical minor = 13.84 mm), blank diameter = 15.80 mm; (b) M6 x 1.0: TDS = 5.0 mm, blank diameter = 5.90 mm.
(a) A double-start (2-start) Acme screw has a pitch of 3 mm. Find its lead and the number of turns needed to move a carriage 48 mm. (b) An imperial bolt is marked 16 TPI (threads per inch). Calculate its pitch in inches and in millimetres (1 inch = 25.4 mm).
(a) Double-start Acme thread:
- Lead = Starts x Pitch = 2 x 3 = 6.0 mm.
- Number of turns for 48 mm travel = 48 / 6.0 = 8 turns.
(b) Pitch of a 16 TPI thread:
- Pitch in inches = 1 / TPI = 1 / 16 = 0.0625 inch.
- Pitch in millimetres = 25.4 / 16 = 1.5875 mm (approx. 1.59 mm).
(a) Lead = 6.0 mm, turns required = 8 turns; (b) Pitch = 0.0625 inch (1.59 mm).
Classify screw threads according to profile (form) and compare ISO Metric V-thread, Square thread, Acme thread, and Buttress thread in terms of thread angle, crest/root shape, and typical applications.
Summarize thread profile classification: Screw threads are classified by profile into V-threads (Metric, Unified, BSW, BA) used primarily for fastening, and power-transmission forms (Square, Acme, Buttress, Knuckle) used for transmitting motion and heavy loads.
Compare the four named profiles:
- ISO Metric V-thread: 60-degree included angle; flat crest, rounded root; standard bolts, nuts, and general machine fastening.
- Square thread: 90-degree vertical flanks (0-degree angle); flat crest and root; highest mechanical efficiency and zero radial bursting force, used in screw jacks and vice screws.
- Acme thread: 29-degree included angle; flat crest and root; stronger root than square threads and allows split half-nuts to engage/disengage easily on lathe leadscrews.
- Buttress thread: Asymmetric flanks (45-degree trailing face, 7-degree vertical load face); flat crest and root; resists very heavy axial thrust in one direction only (quick-release bench vices, heavy presses).
ISO Metric (60 deg, fastening); Square (vertical 90-deg flanks, screw jacks/vices with no radial thrust); Acme (29 deg, lathe leadscrews for split-nut engagement); Buttress (45 deg / 7 deg asymmetric, heavy unidirectional axial loads).
Identify the three taps in a standard hand tap set, explain why all three are needed when threading a blind hole, and state four care rules to avoid breaking a tap inside a workpiece.
The three taps in a hand tap set:
- Taper (First) Tap: 6–8 threads chamfered at the tip; starts straight and cuts ~60% of the thread profile gradually.
- Second (Intermediate) Tap: 3–4 threads chamfered; cuts the thread deeper and closer to full form.
- Bottoming (Third) Tap: 1–1.5 threads chamfered (flat tip); finishes full-depth threads right down to the bottom of a blind hole.
(In a blind hole, a taper tap alone leaves the bottom 6–8 pitches shallow or unthreaded; following sequentially with second and bottoming taps produces full-depth threads safely.)
Four essential care rules to prevent tap breakage:
- Drill the exact tap drill size (never undersize) and lightly countersink the entry.
- Check perpendicularity with a try square during the first 2 turns—side bending snaps brittle taps.
- Reverse 1/2 turn after every 1/2–1 turn forward to break chips and clear blind-hole chip buildup frequently.
- Use proper cutting fluid (cutting oil for steel) and never force a jammed tap.
Set consists of Taper (6–8 thread lead, starts cut), Second (3–4 thread lead), and Bottoming (1–1.5 thread lead, finishes blind-hole bottoms). To prevent breakage: drill correct TDS, verify squareness with a try square, reverse 1/2 turn frequently to break chips, and use cutting oil without forcing.
Differentiate between a solid circular die, a split circular button die, and a hexagonal die nut. Outline the step-by-step procedure for cutting an external thread by hand on a mild steel rod.
Compare the three dies:
- Solid Circular Die: One-piece non-adjustable ring cut to fixed nominal size; used for finishing passes or light re-cutting.
- Split Circular Button Die: Has a radial slit and V-notch controlled by set screws in the die stock, allowing the die to be expanded for an easier first cut and closed for a precise final pass.
- Hexagonal Die Nut: Hex-shaped hardened cutter turned with a spanner; used only to clean or restore damaged/rusty threads, never to cut new threads on plain rod.
Hand external threading procedure:
- Prepare the rod slightly undersize (D - 0.1p) and chamfer the tip 45 degrees.
- Clamp vertically in a bench vice (using soft jaws if needed).
- Expand a split die slightly in the die stock with its chamfered side down, press squarely onto the rod tip, and start 1–2 turns clockwise while keeping the stock horizontal.
- Apply cutting oil and advance 1/2 turn forward, 1/2 turn back to break chips down to length.
- Clean chips, close the split die slightly to nominal size, run a finishing pass, and check with a standard nut.
Solid die (fixed non-adjustable), split button die (slotted for expanding/closing multi-pass cuts), die nut (hexagonal, for re-chasing damaged threads only). External threading steps: size rod to D - 0.1p and chamfer 45 deg -> clamp vertically -> start chamfered die face squarely -> cut with 1/2 forward / 1/2 reverse chip-breaking strokes and oil -> tighten split die for final sizing pass.