PadhaikoAll subjects

Sheet Metal

Engineering Workshop (ENME 106)

Open in the Padhaiko app

4.1 Introduction, sheet metal tools, sheet metal operation

Sheet metal work involves marking, cutting, bending, forming, and joining thin metal sheets (typically 0.4 mm to 3 mm thick; thicker plates above 5–6 mm fall under plate/boiler fabrication) to manufacture ducts, hoppers, funnels, cabinets, guards, and trays.

Common Sheet Metals and Standard Wire Gauge (SWG)

Sheet Metal Tools

Essential Sheet Metal Tools and Their Functions
CategoryTool NameSpecific Function
Marking & MeasuringSteel Rule, Scriber, Divider, TrammelsLinear measurement, scribing layout lines, and drawing large arcs/circles (trammels) on sheet surfaces
MeasuringStandard Wire Gauge (SWG)Circular notched steel plate used to verify sheet thickness gauge
CuttingStraight SnipsHand shears with straight blades for cutting straight lines and wide convex external curves in thin sheet (up to ~1.2 mm MS)
CuttingBent (Curved) SnipsCurved blades designed to trim internal holes and sharp circular curves cleanly
CuttingLever / Bench Shear & Hollow PunchBench-mounted shear for thicker sheet; hollow punch cuts circular holes for pipes/grommets
Striking & FormingWooden / Rawhide MalletFlattens sheets and folds hems/seams without stretching or denting the metal
Striking & FormingSetting, Raising, & Planishing HammersSetting hammer sharpens corners/seams; raising hammer stretches bowls; planishing hammer smooths dents
Supporting (Stakes)Hatchet StakeSharp straight bevelled edge for making crisp 90-degree bends and folding edges
Supporting (Stakes)Beakhorn (Bick Iron) StakeDouble-ended anvil (one conical horn, one square horn) for forming tubes, cones, and square boxes
Supporting (Stakes)Funnel & Half-Moon StakesFunnel stake forms tapered cones; half-moon stake turns up flanges on circular discs
Supporting (Stakes)Creasing Stake & Hand GrooverCreasing stake has grooves for wired edges; hand groover locks and flattens grooved seams

Sheet Metal Operations

  1. Pattern Development & Layout: Before cutting, the 3D object surface is unfolded into a flat 2D pattern (using parallel-line development for cylinders/prisms, radial-line development for cones/pyramids, or triangulation for transition pieces), adding allowances for hems, seams, and bends.
  2. Shearing and Snipping: Cutting along layout lines with straight or curved snips (keep the waste strip curling downward on the right/left side without pinching the snip handles completely closed to avoid jagged notches).
  3. Notching: Cutting small V-shaped or rectangular corner cutouts before bending so folded edges meet neatly without overlapping bulges.
  4. Bending and Folding: Turning flanges over folding bars, a hatchet stake, or a sheet bending brake.
  5. Hemming and Wiring: Folding a sharp raw sheet edge back onto itself by 180 degrees (single hem or double hem) or wrapping it around a steel wire (wired edge) to eliminate sharp burrs and dramatically increase edge stiffness.
  6. Seaming: Joining two sheet edges mechanically without welding—common types are lap seam (soldered/riveted), grooved (locked) seam (interlocked folded hooks locked with a hand groover), single/double bottom seam, and standing seam.
  7. Hollowing, Raising, and Planishing: Beating flat discs into hollow bowls over wooden blocks/sandbags and smoothing hammer marks on a polished planishing stake.

4.2 Rivet types, types of rivet joints, riveting tools and their uses, riveting procedure

Riveting is a permanent mechanical fastening method using a ductile metal pin (rivet) that has a preformed head at one end and a cylindrical shank whose protruding tail is upset (deformed) into a second closing head after passing through aligned holes in the sheets or plates.

Rivet Types

Common Rivet Head Profiles and Applications
Rivet TypeHead GeometryTypical Use
Snap (Cup / Round) HeadHemispherical dome (height ~ 0.7d, diameter ~ 1.6d)General structural steelwork, pressure vessels, and heavy sheet fabrication
Pan HeadTruncated cone with flat topHigh shear strength assemblies, heavy boiler/tank seams
Countersunk Head (60 / 90 deg)Conical head seated inside a countersunk holeFlush aerodynamic/sliding surfaces (chutes, machine guards, aircraft skins)
Flat (Tinman's) HeadWide, thin flat headLight sheet metal boxes, ducts, and thin GI joints
Mushroom / Truss HeadLow-profile wide domeThin sheet metal and non-metallic panels where low snag clearance is needed
Pop (Blind) RivetHollow tubular rivet with central pull-mandrelJoining sheet metal when access is available from one side only

Types of Riveted Joints

Riveted joints are classified by how the sheets/plates meet and how many rows of rivets are used:

AspectLap JointButt Joint
Plate ArrangementOne plate overlaps directly over the edge of the otherTwo plates meet edge-to-edge in the same plane; covered by one (single-strap) or two (double-strap) cover plates
Shear Planes on RivetSingle shear (one cross-section resists load)Single shear (single strap) or double shear (double strap—twice the shear capacity)
Bending StressEccentric load lines induce slight bending momentDouble-strap butt joint keeps load aligned with minimal bending
Row ArrangementsSingle-riveted, double-riveted chain (aligned rows), or zig-zag (staggered rows)Single-riveted or multi-riveted on each side of the butt line
Definition

Standard Riveted Joint Proportions

Riveting Tools and Their Uses

Step-by-Step Riveting Procedure

  1. Mark and Punch/Drill Holes: Lay out rivet centerlines observing minimum margin (m >= 1.5d) and pitch (p >= 3d). Drill or punch holes 0.5–1.0 mm larger than nominal rivet diameter (clearance hole) in both sheets and deburr all hole edges.
  2. Align and Insert Rivet: Align holes (using a drift if needed), insert the rivet from below/inside so the preformed head rests firmly inside the dolly (held on a vice or anvil).
  3. Draw Sheets Tight (Setting): Place the deep hole of the rivet set over the protruding shank and strike sharply once or twice with the hammer so the sheets seat flush with zero gap.
  4. Upset the Shank: Strike the protruding tail vertically with the flat face of the ball-peen hammer to swell the shank snugly inside the hole, then shape the rough dome using circular blows with the ball peen (or cross blows).
  5. Finish with Rivet Snap: Place the cupped rivet snap squarely over the formed head and strike firmly while rotating slightly to produce a smooth, uniform hemispherical head flush against the sheet.
  6. Inspect Joint: Check that the head is centered, free of radial cracks, and the sheets do not rattle or show gaps between them.

Worked Examples

Example 1

1

Two 9 mm thick mild steel plates are to be joined by a single-riveted lap joint using snap-head rivets. Using Unwin's formula and standard joint proportions, calculate: (a) The nominal rivet diameter (d), (b) The minimum edge margin (m), (c) The minimum pitch (p), and (d) The total rivet length required (taking snap-head shank allowance = 1.5d).

Compute rivet diameter using Unwin's formula (t = 9 mm):

  • d = 6 x sqrt(t) = 6 x sqrt(9) = 6 x 3 = 18 mm (standard structural rivet size; hole drilled slightly oversize, e.g., 19 mm or 19.5 mm).

Compute minimum margin, minimum pitch, and total rivet length:

  • Minimum edge margin: m = 1.5 x d = 1.5 x 18 = 27 mm.
  • Minimum pitch: p = 3 x d = 3 x 18 = 54 mm.
  • Total grip thickness: T = t1 + t2 = 9 + 9 = 18 mm.
  • Snap-head projection allowance: L_proj = 1.5 x d = 1.5 x 18 = 27 mm.
  • Total rivet length: L = T + L_proj = 18 + 27 = 45 mm.
Answer:

Rivet diameter d = 18 mm; minimum edge margin m = 27 mm; minimum pitch p = 54 mm; total rivet length L = 45 mm.

Example 2

2

A hollow galvanized iron (GI) cylinder of diameter 80 mm and finished height 120 mm is to be fabricated from 24 SWG sheet. The cylinder uses a 5 mm grooved (locked) vertical seam (requiring a total seam allowance of 3 x seam width = 15 mm across both ends combined: 5 mm single fold on one edge and 10 mm folded allowance on the mating edge) and a 6 mm single hem on both top and bottom rims. Calculate the exact rectangular blank dimensions (width x height) to mark on the sheet.

Calculate the developed blank width (circumference + grooved seam allowance):

  • Circumference C = pi x D = 3.1416 x 80 = 251.33 mm.
  • Grooved seam allowance = 3 x w = 3 x 5 = 15 mm.
  • Total blank width = 251.33 + 15 = 266.33 mm (approx. 266.5 mm).

Calculate the developed blank height (finished height + top and bottom hems):

  • Finished cylinder height = 120 mm.
  • Single hem allowance at top = 6 mm; single hem allowance at bottom = 6 mm.
  • Total blank height = 120 + 6 + 6 = 132 mm.
Answer:

Mark and cut a rectangular GI blank measuring 266.3 mm (approx. 266.5 mm) x 132 mm (with 5 mm fold line at one vertical edge, 10 mm fold lines at the other, and 6 mm hem lines along top and bottom).

Example 3

3

Describe the exact workshop steps and tools needed to form and lock a 5 mm grooved seam on a rolled GI sheet cylinder, and then turn a 6 mm single hem around its rim.

Form the opposing hooks and roll the cylinder:

  1. Scribe parallel fold lines at 5 mm inward from both vertical ends of the blank (avoid deep scratches that crack the zinc coating).
  2. Clamp each vertical edge in folding bars (or over the sharp edge of a hatchet stake), bend to 90 degrees with a wooden mallet, and fold further to about 135–150 degrees in opposite directions (one hook pointing inward, the other pointing outward).
  3. Roll the sheet smoothly around a cylindrical mandrel / beakhorn stake with palm pressure and light mallet taps until the two opposite hooks interlock.

Lock the grooved seam and form the single hem:

  1. Slide the cylinder over a solid mandrel stake with the interlocked seam resting on top.
  2. Press the hooked edges together with a wooden mallet, then position a 5 mm hand groover squarely over the seam ridge and strike firmly with a hammer along the entire length to offset and lock the seam mechanically. Flatten lightly with a mallet.
  3. For the 6 mm single hem around the rim, scribe a 6 mm line around the cylinder end, gradually turn the rim outward over a half-moon / hatchet stake using glancing mallet blows while rotating the cylinder, and close the hem flat against the cylinder wall.
Answer:

Fold 5 mm edges in opposite directions over a hatchet stake/folding bars -> roll cylinder on a mandrel -> interlock hooks -> lock along the ridge using a hand groover and hammer -> turn the 6 mm edge progressively around a stake and flatten with a wooden mallet for the single hem.


Exercises

added

Question 1

Two 16 mm thick steel plates are joined by a riveted lap joint using snap-head rivets. Using Unwin's formula, calculate: (a) the rivet diameter d, (b) the minimum edge margin m, (c) the minimum pitch p, and (d) the total rivet length L (taking snap-head shank allowance = 1.5d).

Apply Unwin's formula (t = 16 mm):

  • Rivet diameter: d = 6 x sqrt(16) = 6 x 4 = 24 mm.

Compute margin, pitch, and total rivet length:

  • Minimum edge margin: m = 1.5 x 24 = 36 mm.
  • Minimum pitch: p = 3 x 24 = 72 mm.
  • Total plate thickness: T = 16 + 16 = 32 mm.
  • Snap-head allowance = 1.5 x 24 = 36 mm.
  • Total rivet length: L = 32 + 36 = 68 mm.
Answer:

Rivet diameter d = 24 mm, minimum margin m = 36 mm, minimum pitch p = 72 mm, total rivet length L = 68 mm.

Question 2

An open rectangular sheet-metal tray has internal base dimensions 150 mm x 100 mm, vertical wall height 30 mm, and a 6 mm single hem folded outward along the top rim of all four sides (corner flaps are left as 10 mm tabs on two opposite sides, or square corners notched out). Calculate the overall flat blank length and width before notching, and compute the net blank area (in sq mm) after cutting out four square corners of side (30 + 6) = 36 mm.

Compute overall flat blank length and width:

  • Overall length = Base length + 2 x (Wall height + Hem) = 150 + 2 x (30 + 6) = 150 + 72 = 222 mm.
  • Overall width = Base width + 2 x (Wall height + Hem) = 100 + 2 x (30 + 6) = 100 + 72 = 172 mm.

Compute net blank area after corner cutouts:

  • Gross rectangular area = 222 x 172 = 38184 sq mm.
  • Area of 4 square corner cutouts (36 mm x 36 mm each) = 4 x (36 x 36) = 4 x 1296 = 5184 sq mm.
  • Net area of notched blank = 38184 - 5184 = 33000 sq mm.
Answer:

Overall blank dimensions = 222 mm x 172 mm; net notched blank area = 33000 sq mm.

Question 3

What is the Standard Wire Gauge (SWG) rule for sheet thickness? Name five common sheet metal stakes and state the specific forming operation performed on each.

Explain SWG convention: Standard Wire Gauge (SWG) designates sheet thickness by gauge numbers on a notched gauge disc. Higher SWG numbers correspond to thinner sheets (for instance, 16 SWG is 1.63 mm while 26 SWG is 0.46 mm).

List five stakes and their uses:

  1. Hatchet Stake: Sharp straight bevelled edge for sharp 90-degree bends, folding hems, and box edges.
  2. Beakhorn (Bick Iron) Stake: Dual tapered conical and rectangular horns for rolling cylinders, cones, and square pipes.
  3. Funnel Stake: Long steep conical horn for shaping tapered funnels and frustums.
  4. Half-Moon Stake: Curved beveled flange for turning up edges on circular disc bottoms.
  5. Creasing Stake: Rectangular bar with machined grooves for curling wired edges and forming beads.
Answer:

In SWG, higher gauge numbers mean thinner sheets. Five stakes: Hatchet (sharp straight bends/hems), Beakhorn (tubes/cones/boxes), Funnel (tapered cones), Half-moon (flanging circular discs), and Creasing (wired edges and beads).

Question 4

Compare a riveted lap joint with a double-strap riveted butt joint, and explain the difference between chain riveting and zig-zag riveting.

Compare lap joint vs. double-strap butt joint:

  • Lap joint: One plate overlaps directly over the other; rivets experience single shear and slight bending because the tensile forces in the two plates are offset. Simpler and lighter for thin sheets.
  • Double-strap butt joint: Main plates meet edge-to-edge in one plane and are sandwiched by top and bottom cover straps; rivets experience double shear (double load capacity per rivet) and practically zero eccentric bending. Preferred for heavy structural plates and boilers.

Chain vs. zig-zag riveting:

  • Chain riveting: Rivets in adjacent rows sit directly opposite one another along transverse lines (square grid).
  • Zig-zag (staggered) riveting: Rivets in the second row are offset by half a pitch midway between the rivets of the first row, preserving a larger net plate cross-section and giving tighter edge clamping.
Answer:

A lap joint overlaps plates (single shear, eccentric bending), whereas a double-strap butt joint aligns plates edge-to-edge between two straps (double shear, balanced load). Chain riveting aligns rows directly opposite each other; zig-zag riveting staggers adjacent rows by half a pitch for higher joint efficiency.

Question 5

List the essential riveting tools and describe the step-by-step manual riveting procedure using a snap-head rivet. Mention two common riveting defects and how to avoid them.

Riveting tools and manual procedure:

  • Tools: Drill/punch, drift/reamer, dolly (holder-on), rivet set, ball-peen hammer, and rivet snap.
  • Procedure: (1) Drill matching clearance holes (0.5–1 mm larger than d) and deburr; (2) Insert rivet and support the preformed head on the dolly; (3) Seat sheets tightly together using the deep hole of the rivet set; (4) Strike tail squarely with flat hammer face to upset the shank in the hole, then rough-shape dome with ball peen; (5) Cup and smooth the closing head with the rivet snap.

Two common defects and prevention:

  1. Gap between sheets (loose joint): Caused by skipping the rivet set; prevented by drawing sheets flush with the rivet set before upsetting the shank.
  2. Bent or off-center closing head: Caused by overly long shank projection (> 1.5d) or misaligned holes; prevented by trimming shank allowance to 1.25d–1.5d and aligning holes with a drift/reamer before inserting the rivet.
Answer:

Tools: dolly, rivet set, ball-peen hammer, rivet snap, drift/reamer. Steps: drill & deburr -> support head on dolly -> pull sheets tight with rivet set -> upset shank & rough-form dome -> finish dome with rivet snap. Avoid sheet gaps (use rivet set) and bent/off-center heads (keep allowance 1.25d–1.5d and align holes properly).

← Thread CuttingMachine Tools →