Electrochemistry and Buffer
Open in the Padhaiko app1.1 Electrochemistry
1.1.1 Introduction
Electrochemistry studies the interconversion of chemical energy and electrical energy through redox reactions. A galvanic (voltaic) cell converts the energy of a spontaneous redox reaction into electrical work, while an electrolytic cell uses an external source to drive a non-spontaneous reaction (electrolysis).
Galvanic Cell and Cell Notation
A galvanic cell has two half-cells joined by a salt bridge (which completes the circuit and keeps each half-cell electrically neutral).
- Anode: the electrode where oxidation occurs (negative pole in a galvanic cell).
- Cathode: the electrode where reduction occurs (positive pole in a galvanic cell).
- Cell notation: anode (left) electrolyte electrolyte cathode (right), for example the Daniell cell
with anode reaction and cathode reaction .
Standard electrode potentials (reduction, , ): , , , . The standard cell emf is
A reaction is spontaneous when .
1.1.2 EMF of a galvanic cell and the Nernst equation
The free energy change and emf are related by
where is the number of electrons transferred and .
Nernst Equation
For the reaction with reaction quotient , substituting gives
For a single electrode, . At equilibrium and :
Concentration cell: two electrodes of the same metal in solutions of different concentration have and (), driven by the tendency of the concentrations to equalize.
1.1
For the cell at , find (a) , (b) , (c) and the equilibrium constant. (d) Find the emf of the concentration cell .
(a) Standard emf: .
(b) Nernst equation (, ):
(c) Free energy and equilibrium constant:
(d) Concentration cell:
(a) ; (b) ; (c) , ; (d) .
1.1.3 Polarization and overpotential
When current flows, the electrode potential departs from its equilibrium (reversible) value. This deviation is polarization, and its magnitude is the overpotential .
| Type | Cause | Reduced by |
|---|---|---|
| Activation (charge-transfer) | Slow electron-transfer step at the electrode | Better electrocatalyst, higher temperature |
| Concentration | Reactant depleted (or product accumulated) at the electrode surface because diffusion is slow | Stirring, higher concentration |
| Ohmic (resistance) | Resistance of electrolyte, film or contacts ( drop) | Closer electrodes, conducting electrolyte |
In a galvanic cell polarization lowers the terminal voltage; in electrolysis it raises the voltage needed. Hydrogen overpotential on mercury or lead is why zinc can be electroplated from aqueous solution even though .
1.1.4 Butler-Volmer equation and Tafel plots
Butler-Volmer Equation
For a one-step electrode reaction with equal surface and bulk concentrations (no mass-transfer limit), the net current density is
where is the exchange current density (the equal forward and backward rate at equilibrium), and are the anodic and cathodic transfer coefficients ( for one electron, typically each), and the overpotential.
- Small overpotential (): linearizing, , so the current is proportional to (the charge-transfer resistance is ).
- Large overpotential (): one exponential dominates. For the anodic branch , which is the Tafel equation
A plot of against (Tafel plot) is a straight line with slope (the Tafel slope, for , ) and an intercept that gives . A large means a fast, reversible electrode; a small means a sluggish one that needs a high overpotential.
1.2
An electrode has , and at . Find the anodic current density at (use the Tafel approximation) and the Tafel slope.
Tafel slope:
Current density:
(The ignored cathodic term is of the anodic one, so the Tafel approximation is valid.)
; .
1.2 Electrode processes and mechanisms (qualitative only)
1.2.1 Charge transfer processes at electrodes
At an electrode surface a reaction takes place in a sequence of steps. The slowest step controls the rate.
- Mass transport of the reactant from the bulk to the electrode surface.
- Adsorption of the species on the surface (and any preceding chemical step).
- Electron transfer across the interface: the electron tunnels between the electrode and the species in the electrical double layer, a layer of charge on the electrode and a layer of oppositely charged ions in solution a few nanometres thick that sets up a large electric field.
- Desorption and transport of the product away (or formation of a new phase such as a deposit or gas bubbles).
The rate of the electron-transfer step increases exponentially with the potential applied across the double layer, which is the physical basis of the Butler-Volmer equation. Surface condition and the nature of the electrode (the electrocatalyst) change by many orders of magnitude.
1.2.2 Mass transfer and diffusion in electrochemical systems
Species reach an electrode by three modes of mass transport:
- Diffusion: movement down a concentration gradient (Fick's law, ) near the surface in a diffusion layer of thickness .
- Migration: movement of ions in the electric field (suppressed by adding an excess of supporting electrolyte).
- Convection: movement by stirring, flow or rotation of the electrode.
When the reaction is fast, the surface concentration falls to zero and the current reaches a limiting current set by diffusion, . Raising the overpotential further does not increase the current. This is concentration polarization, and it is why stirring increases the current in electroplating and sensors.
1.3 Industrial and applied electrochemistry
1.3.1 Batteries: lead-acid and lithium-ion
| Aspect | Lead-acid battery | Lithium-ion battery |
|---|---|---|
| Anode (discharge) | Spongy lead, | Lithiated graphite, |
| Cathode (discharge) | ||
| Electrolyte | Dilute (about , density to ) | Lithium salt () in organic carbonate solvent |
| Cell voltage | About (6 cells give ) | About to |
| Energy density | Low ( to ) | High ( to ) |
| Uses | Starting, lighting, ignition in vehicles, UPS, inverters | Phones, laptops, electric vehicles, grid storage |
Lead-acid overall reaction:
The acid is consumed on discharge so its density falls, which is a measure of the state of charge. Lithium-ion cells work by the shuttling of between layered electrodes (the "rocking-chair" mechanism) without any metallic lithium formed: on charging leaves the cobalt oxide and intercalates between graphite layers.
1.3.2 Solar photovoltaic cell and fuel cell
Solar photovoltaic (PV) cell. A - junction of silicon. A photon with energy (band gap, for Si) creates an electron-hole pair in the depletion region; the built-in field separates them, and the electrons flow through the external circuit. Typical examples are monocrystalline and polycrystalline silicon panels (efficiency about to ), thin-film cells (CdTe, CIGS), and dye-sensitized and perovskite cells. The efficiency is
with the irradiance ( at standard conditions) and the area. The longest wavelength absorbed by silicon is .
Fuel cell. A fuel cell converts the chemical energy of a continuously supplied fuel directly into electricity. In the hydrogen-oxygen (PEM) fuel cell:
- Anode:
- Cathode:
- Overall: , with
Its thermodynamic efficiency is , far above that of a heat engine, and the only product is water. Types include PEM, alkaline and solid-oxide fuel cells.
1.3.3 Corrosion
Corrosion is the gradual destruction of a metal by chemical or electrochemical reaction with its environment. Rusting of iron in moist air is electrochemical: some regions of the surface act as anodes and others as cathodes.
Electrochemical Theory of Rusting of Iron
- Anode:
- Cathode (neutral or basic, dissolved oxygen): (in acidic solution )
- Further oxidation: (rust, )
Corrosion is faster in the presence of moisture, dissolved salts, acids, impurities and differences in oxygen concentration (differential aeration, for example under a water drop).
Control of corrosion: protective coatings (paint, galvanizing, tinning), sacrificial anode (cathodic protection by attaching a more active metal such as Zn or Mg), impressed-current cathodic protection (the structure is made the cathode of an external DC source), corrosion inhibitors, and alloying (stainless steel).
1.3
(a) Calculate the theoretical specific capacity of a graphite anode for in (). (b) Find the thermodynamic efficiency of a hydrogen fuel cell with and . (c) A steady corrosion current of flows for by ; find the mass of iron lost ().
(a) Specific capacity: One unit stores , so
(b) Efficiency:
(c) Mass lost (Faraday's law):
(a) ; (b) ; (c) of iron.
1.4 Buffer, buffer range, buffer capacity and buffer solution (Henderson-Hasselbalch equation) and its applications
A buffer solution resists a change in pH when small amounts of acid or base are added, or on dilution.
- Acidic buffer: weak acid and its salt with a strong base, for example ().
- Basic buffer: weak base and its salt with a strong acid, for example ().
Action. In an acetate buffer, added is consumed by acetate () and added is consumed by the acid (), so the ratio changes only slightly.
Henderson-Hasselbalch Equation
From , taking :
For a basic buffer, and .
Buffer range. A buffer is effective only when , i.e. in the range
Buffer capacity is the number of moles of strong acid or base needed to change the pH of of buffer by one unit:
It is greatest when (), where , and it increases with the total concentration of the buffer components.
Applications: blood is buffered at pH by (and phosphate and protein buffers); buffers are used in fermentation, in the analysis laboratory (calibration of pH meters, colorimetric tests), in electroplating baths, in pharmaceutical products and eye drops, in boiler-water and soil treatment, and in the manufacture of leather and dyes.
1.4
An acetate buffer () contains and . (a) Find its pH. (b) A different buffer with each of acid and salt in receives of HCl; find the new pH and the buffer capacity.
(a) pH of the buffer:
(b) After adding HCl: The converts acetate to acetic acid: , .
For comparison, HCl in unbuffered water ( from to ) changes the pH by units.
(a) ; (b) and (close to ).
Exercises
Practice Exercises — Electrochemistry and Buffer
Derive the Nernst equation for a cell reaction. Calculate the emf of the cell (reaction ) at (, ).
Derivation: and , give , which at is .
Numbers (): and .
.
Explain polarization and overpotential. Describe the three kinds of polarization and say how each can be reduced.
Meaning: Polarization is the departure of an electrode potential from its equilibrium value when current flows, and overpotential is its magnitude.
Types: Activation polarization is caused by the slow electron-transfer step and is reduced by an electrocatalyst. Concentration polarization is caused by depletion of the reactant near the electrode and is reduced by stirring. Ohmic polarization is the drop in electrolyte and contacts and is reduced by bringing the electrodes closer or by adding conducting electrolyte.
Polarization lowers the voltage of a galvanic cell and raises the voltage needed for electrolysis; its three kinds are activation, concentration and ohmic.
Write the Butler-Volmer equation and obtain the Tafel equation from it. For a reaction with , at , by how many volts must the overpotential increase to raise the current density tenfold? If , what current density flows at (use the Tafel form)?
From Butler-Volmer to Tafel: . At large positive the second term is negligible, so , i.e. with .
Tenfold change in :
Current at : decades, so .
per decade; .
Describe the construction and working of the lead-acid storage battery with the cell reactions. Compare it with the lithium-ion cell. Explain how corrosion of iron occurs and name three methods of controlling it.
Lead-acid cell: Anode: spongy Pb; cathode: on a lead grid; electrolyte: . On discharge and , so and the cell gives about . Charging reverses these reactions.
Comparison with Li-ion: Li-ion has a higher cell voltage () and a much higher energy density because shuttles between graphite and ; lead-acid is cheaper and delivers high surge current but is heavy.
Rusting and control: Rusting is electrochemical: at anodic spots and at cathodic spots, giving (rust). It is controlled by coatings (paint, galvanizing), sacrificial anodes (Zn, Mg) and impressed-current protection.
Lead-acid: , per cell. Corrosion control: coatings, sacrificial anode, impressed current.
Define buffer solution, buffer range and buffer capacity. How many moles of sodium acetate must be added to of acetic acid () to prepare a buffer of pH ? State the pH change when of NaOH is added to this buffer.
Definitions: A buffer resists change of pH on adding small amounts of acid or base. Its range is and its capacity is the moles of acid or base per litre needed to change the pH by one unit.
Amount of salt:
So of sodium acetate is needed.
After adding NaOH: Acid falls to and acetate rises to :
The pH rises by only .
of sodium acetate; pH becomes (a change of ).