Explosives, Lubricants and Paints
Open in the Padhaiko app8.1 Explosives
An explosive is a substance (or mixture) that, when initiated by heat, shock or friction, undergoes a very rapid exothermic decomposition that produces a large volume of hot gases, so that a sudden high pressure (blast wave) is created. Requirements: highly exothermic, rapid reaction, large volume of gas, and enough stability for safe storage.
Oxygen balance. For an explosive of molar mass the oxygen balance (percentage of oxygen needed or in surplus for complete oxidation of C to and H to ) is
A positive value means excess oxygen; a value near zero gives the most energy.
8.1.1 Types of explosives: primary, low and high explosives
| Type | Behaviour | Examples | Use |
|---|---|---|---|
| Primary (initiating) explosives | Extremely sensitive to heat, shock, friction; detonate at once in a small amount | Lead azide , mercury fulminate , lead styphnate | Detonators and percussion caps to initiate the main charge |
| Low explosives (propellants) | Deflagrate (burn rapidly) at to ; push rather than shatter | Black powder (, S, C), smokeless powder (nitrocellulose), rocket fuels | Fireworks, fuse, bullets and rocket propulsion, mining of soft rock |
| High explosives (secondary) | Detonate with a shock wave at to ; need a detonator to initiate | TNT, nitroglycerine, dynamite, RDX, PETN, plastic explosives | Mining, demolition, tunnelling, shells and bombs |
Black powder: (typically , S, C).
8.1.2 Preparation and applications of TNT, TNG, nitrocellulose and plastic explosives
| Explosive | Preparation | Decomposition and properties | Applications |
|---|---|---|---|
| TNT (2,4,6-trinitrotoluene, ) | Toluene is nitrated in three stages with mixed acid ( and ) at increasing temperature: toluene to mononitro to dinitro to trinitrotoluene | (much soot); stable, insensitive, melts at so it can be cast | Shells, bombs, mining and demolition; standard for rating explosive power |
| TNG (nitroglycerine, glyceryl trinitrate, ) | Glycerol added slowly to mixed acid kept below : | ; oily liquid, very shock sensitive | Dynamite (absorbed in kieselguhr, Nobel 1867), propellants; also a vasodilator for angina |
| Nitrocellulose (guncotton) | Cellulose treated with and (esterification of groups): | Fully nitrated: N (guncotton, above N); lower nitrogen (about ) is pyroxylin | Smokeless powder, lacquers, celluloid and collodion; high-nitrogen form for blasting |
| Plastic explosives (C-4, Semtex) | RDX (made by nitrolysis of hexamine with ) or PETN mixed with a plasticizer and binder (about RDX with polyisobutylene and oil in C-4) | Mouldable like putty, stable and safe until detonated, very high detonation velocity () | Demolition, military engineering, cutting charges, shaped charges |
Dynamite is absorbed in an inert porous material that makes it safe to handle. Nitroglycerine and TNT show how oxygen balance governs the products: TNT is oxygen-poor and gives carbon (soot) and CO, while nitroglycerine has a small excess of oxygen and gives only , , and .
8.1
Use and . (a) Find the oxygen balance of TNT () and of nitroglycerine (). (b) Find the volume of gas (at STP, taking all products as gases) from of nitroglycerine. (c) Find the percentage of nitrogen in fully nitrated cellulose, ().
(a) Oxygen balance:
TNT lacks oxygen (hence the soot), while nitroglycerine has a slight excess.
(b) Gas from nitroglycerine: gives mol gas per mol, i.e. mol per mol of TNG.
(so of liquid expands to about of gas at STP, and much more at the explosion temperature).
(c) Nitrogen content: .
(a) and ; (b) ; (c) nitrogen.
8.2 Lubricants: introduction, function and classification
A lubricant is a substance introduced between two moving surfaces to reduce friction and wear. A lubricant also carries away heat, keeps surfaces clean, seals gaps (piston rings), protects against corrosion and damps shock and noise.
Mechanisms of lubrication.
- Fluid-film (hydrodynamic) lubrication: a thick film of oil completely separates the surfaces so that friction depends only on the internal viscous friction of the oil (journal bearings at high speed). The coefficient of friction is very low ( to ).
- Boundary lubrication: under heavy load or low speed the film is a thin adsorbed layer on the metal (fatty acids, soaps), which protects the surfaces from direct contact.
- Extreme-pressure lubrication: additives containing S, P or Cl react with the metal at high temperature to give a sacrificial film of sulfide, phosphate or chloride (gears).
| Class | Types | Examples and uses |
|---|---|---|
| Liquid (oils) | Animal and vegetable oils (fatty oils) | Castor oil, palm oil, tallow: low-temperature and light machinery; oxidize and gum, so poor for engines |
| Liquid (oils) | Mineral (petroleum) oils | Most widely used: engine oil, gear oil, turbine oil; cheap and stable |
| Liquid (oils) | Synthetic oils | Polyalphaolefins, esters, silicones, polyglycols: very wide temperature range, jet engines, and aircraft |
| Semi-solid (greases) | Lubricating oil thickened with a metallic soap (Ca, Na, Li) or a non-soap thickener | Calcium grease (water resistant), sodium grease (hot), lithium grease (universal): bearings and chassis points, where oil would run away |
| Solid | Graphite, molybdenum disulfide , boron nitride, PTFE, talc | Layered structure with weak interlayer forces lets the layers slide; used at very high temperature or vacuum, or when oil is not allowed (food and textile machinery) |
Important properties of lubricating oils.
- Viscosity (resistance to flow) and the viscosity index (VI), a measure of its change with temperature: , where is the viscosity of the test oil at , and and are the viscosities at of the reference oils of and with the same viscosity at as the test oil. A high VI means little change in viscosity with temperature.
- Flash point and fire point: the lowest temperature at which the vapour ignites momentarily or continuously; it should be well above the working temperature.
- Cloud point and pour point: the temperature at which wax crystals first appear (cloud) and below which the oil stops flowing (pour); they should be below the lowest operating temperature.
- Acid value (neutralization number): mg of KOH to neutralize the free acid in of oil; acids corrode metals, so it must be low. .
- Saponification value: mg of KOH to saponify of oil, with and the blank and sample titres of acid; it indicates the presence of fatty (animal and vegetable) oils, and a pure mineral oil has a value of zero.
- Aniline point: the lowest temperature at which equal volumes of oil and aniline mix; a high value means few aromatics and so less damage to rubber seals.
8.2
(a) An oil sample of is refluxed with alcoholic KOH; the blank titration needs and the sample of HCl. Find the saponification value. (b) of a lubricating oil requires of KOH for neutralization; find the acid value. (c) A test oil has while the and reference oils have and (all in mm/s at ); find the viscosity index.
(a) Saponification value:
(b) Acid value:
(c) Viscosity index:
(a) (a fatty oil, not a mineral oil); (b) ; (c) .
8.3 Paints
A paint is a dispersion of finely divided pigment in a liquid medium (vehicle) that is applied as a thin film to a surface, where it dries to a continuous, adherent, protective and decorative coating.
8.3.1 Introduction, requisites, types and applications
| Constituent | Function | Examples |
|---|---|---|
| Pigment | Gives colour and opacity (covering power), protects the substrate, and increases the hardness | White: (best), ZnO; red: ; black: carbon black; blue: ultramarine; green: ; anticorrosive: zinc phosphate, red lead |
| Binder (vehicle, drying oil or resin) | Holds the pigment particles together and bonds the film to the surface; forms the film on drying (by oxidation or polymerization) | Linseed oil, alkyd, acrylic latex, epoxy, polyurethane |
| Solvent (thinner) | Dissolves the binder and adjusts the viscosity for application; evaporates afterwards | Turpentine, mineral spirit, xylene, water (emulsion paints) |
| Drier | Speeds up oxidation and drying of the oil | Naphthenates and octoates of Co, Mn and Zr (formerly Pb) |
| Extender (filler) | Cheap, reduces cost and improves body and hardness | (barytes), , talc, china clay |
| Plasticizer and additives | Flexibility and resistance to cracking; wetting agents, anti-fungal, UV stabilizers | Tricresyl phosphate, dibutyl phthalate, biocides |
Requisites of a good paint: easy to apply and spread uniformly; good covering power (opacity); good adhesion and flexibility without cracking; dries in a reasonable time to a smooth, hard film; resists weather, water, light, chemicals and abrasion (durability) and does not fade; protects against corrosion; cheap; and non-toxic with low odour and low emission of harmful solvents.
| Type | Composition | Applications |
|---|---|---|
| Oil paint | Pigment in a drying oil (linseed) with thinner and drier | Wood and metal, interior and exterior surfaces |
| Water-based emulsion (acrylic latex) paint | Pigment and polymer latex dispersed in water | Interior and exterior walls: low odour, quick dry, washable |
| Enamel | Pigment in varnish (resin and oil), hard glossy finish | Doors, furniture, machines, vehicles, appliances |
| Varnish | Natural or synthetic resin dissolved in oil and thinner; transparent, no pigment | Wooden floors and furniture, protecting while showing the grain |
| Lacquer | Nitrocellulose or acrylic resin in a volatile solvent; dries by evaporation only | Automobile, furniture and metal finish |
| Distemper | Chalk or whiting with water-soluble binder (glue, casein) | Cheap interior wall coating |
| Anticorrosive and fireproof paints | Red lead, zinc chromate or zinc-rich primers; intumescent coatings | Steel bridges, ships, pipelines and structures |
Pigment volume concentration governs gloss and permeability; glossy paints have low PVC ( to ) and flat paints a high PVC ( to ).
8.3.2 Environmental and health impact
- Volatile organic compounds (VOCs) from solvent-based paints (toluene, xylene, benzene, formaldehyde) cause headaches, dizziness and damage to the liver and nervous system, and they form ground-level ozone and photochemical smog. Water-based and low-VOC or powder paints reduce this.
- Lead: lead pigments and driers (white lead, red lead) are a neurotoxin that harms the brain development of children, and lead-based paints have been banned in many countries. Chromates () are carcinogenic; cadmium and mercury biocides are toxic. They should be replaced by zinc phosphate, and organic pigments.
- Waste and disposal: paint waste, cleaning solvents and sludge contaminate soil and water; spraying produces mist and nanoparticles; peeling paint releases microplastics; scraping old lead paint produces toxic dust.
- Control: use water-based, low-VOC and lead-free paints; good ventilation and masks while painting; recover solvents and recycle leftover paint; and follow the green chemistry principles of safer solvents and design for degradation.
8.3
(a) A room has of wall to be painted with two coats. The paint covers per litre per coat. How many litres are needed? (b) A paint contains of pigment and of binder per batch; find its PVC. (c) A pigment mix contains by mass; find the mass of in grams.
(a) Quantity of paint:
(b) Pigment volume concentration:
(between glossy and flat, as in a semi-gloss paint).
(c) Titanium dioxide: .
(a) ; (b) ; (c) .
Exercises
Practice Exercises — Explosives, Lubricants and Paints
Classify explosives with two examples of each class and state the use of each. Explain the difference between deflagration and detonation.
Classification: Primary (lead azide, mercury fulminate): very sensitive, used in detonators. Low explosives (black powder, smokeless powder): burn rapidly; used as propellants and fireworks. High explosives (TNT, RDX, nitroglycerine): used in mining and demolition and need a detonator.
Deflagration and detonation: Deflagration is rapid burning that moves through the material at subsonic speed ( to ) by heat conduction; detonation is a supersonic shock wave ( to ) in which the shock compresses and ignites the material.
Primary, low and high explosives; low explosives deflagrate while high explosives detonate.
Describe the preparation of TNT, nitroglycerine and nitrocellulose with equations. Calculate the oxygen balance of RDX, (), and the number of moles of TNT in ().
Preparation: TNT: toluene is nitrated by in three stages: . Nitroglycerine: below . Nitrocellulose: cellulose with mixed acid esterifies the three groups per glucose unit to .
Calculations:
; of TNT.
Define lubricant and state its functions. Describe fluid-film and boundary lubrication and give one example each of liquid, semi-solid and solid lubricants.
Lubricant and functions: A lubricant is placed between moving surfaces to reduce friction and wear. It also cools, seals, cleans and protects from corrosion.
Mechanisms and examples: In fluid-film lubrication a thick film of oil separates the surfaces completely, so only the viscosity of the oil resists the motion (journal bearings). In boundary lubrication a thin adsorbed layer of fatty acid or soap protects the surfaces at low speed and heavy load. Examples: mineral oil (liquid), lithium grease (semi-solid), graphite or (solid).
Liquid: mineral oil; semi-solid: grease; solid: graphite or molybdenum disulfide.
Define flash point, pour point, acid value and viscosity index. of an oil needs of KOH for neutralization; find its acid value. A test oil has with and ; find its viscosity index.
Definitions: The flash point is the lowest temperature at which the oil vapour ignites momentarily; the pour point is the lowest temperature at which the oil still flows; the acid value is the mg of KOH needed to neutralize the free acid in ; the viscosity index measures the change of viscosity with temperature.
Numbers:
; .
List the constituents of a paint with the function and one example of each. Name the properties of a good paint and discuss the environmental and health effects of paints. How much paint is needed to cover with two coats at per litre per coat?
Constituents and requisites: Pigment (colour and opacity: ); binder (film former: linseed oil, alkyd); solvent (viscosity: turpentine, water); drier (Co naphthenate); extender (cheap filler: barytes); plasticizer (flexibility). A good paint has good covering power, adhesion, flexibility, durability, quick drying and low toxicity.
Impact and quantity: VOCs and lead pigments damage health and cause ozone formation; water-based, low-VOC, lead-free paints are the remedy. .
of paint.