Network Transfer Function and Frequency Response
Open in the Padhaiko app4.1 Concept of complex frequency
Complex Frequency
A signal with is the general exponential of circuit theory.
- (nepers/s) sets the decay or growth: decays, grows, is steady.
- (rad/s) sets the oscillation.
- Special cases: DC is ; a pure sinusoid is ; a decaying exponential is ; a damped sinusoid is .
Element impedances in terms of : , , . Putting gives the usual a.c. steady-state impedances.
4.2 Transfer functions of two port networks
Network Function
For a network with zero initial energy, the transfer function is the ratio of the Laplace transform of the output to that of the input:
- Driving-point functions: both quantities at the same port ( or ).
- Transfer functions: quantities at different ports, namely voltage ratio , current ratio , transfer impedance and transfer admittance .
is a ratio of polynomials in with real coefficients:
The impulse response is and the forced sinusoidal response comes from .
4.3 Poles and zeros of networks
Poles, Zeros and Stability
- Zeros : values of where (roots of the numerator).
- Poles : values of where (roots of the denominator). They are the natural frequencies of the circuit.
- Plot them on the -plane: zeros as , poles as .
- A passive network is stable when all poles lie in the left half-plane (). Poles on the axis give sustained oscillation and must be simple.
- Poles and zeros of real networks are real or occur in complex-conjugate pairs.
4.4 Magnitude and phase response
Frequency Response
Putting gives
The magnitude response against and the phase response against together show how the network treats each frequency. Gain in decibels is . For a factor the magnitude is the distance from to the point on the imaginary axis, and the phase is the angle of that line.
| Circuit | Type | frequency | Phase | |
|---|---|---|---|---|
| RC, output across C | low-pass | |||
| CR, output across R | high-pass | |||
| RL, output across R | low-pass |
4.5 Bode diagrams
Bode Plot Construction
A Bode plot has (dB) and phase (degrees) on the vertical axes and on the horizontal axis. Write in standard form of factors and add the factor plots:
- Constant : flat at .
- Pole : 0 dB up to , then falls at . Phase goes (at ) .
- Zero : rises at after . Phase goes .
- Origin factor : straight line of slope through 0 dB at .
The corner (break) frequency is where the asymptotes meet. The exact curve is below (pole) or above (zero) the asymptotes at the corner. One decade is a factor of in and .
4.6 Bandwidth, high-Q and low-Q circuits
Bandwidth and Quality Factor
The half-power (3 dB) bandwidth is , where falls to of its peak. For a resonant circuit with resonant frequency :
The half-power frequencies are and .
- High-Q (): narrow bandwidth, sharp selectivity, .
- Low-Q: wide, gentle peak, poor selectivity.
4.7 Basic concept of filters: high-pass, low-pass, band-stop and band-pass filters
| Filter | Passes | Rejects | Typical circuit |
|---|---|---|---|
| Low-pass | to | above | RC with output across C |
| High-pass | above | to | CR with output across R |
| Band-pass | to | outside the band | series RLC, output across R |
| Band-stop (notch) | outside to | inside the band | series RLC, output across L and C |
4.1
An RC low-pass filter has and . Find the cut-off frequency and the gain (magnitude, dB and phase) at .
Transfer function and cut-off. with :
At . :
; at : (), phase .
4.2
Sketch the Bode magnitude plot for and find the gain at from the asymptotes and exactly.
Break frequencies. The constant is . Poles at and rad/s.
Asymptotes. Flat at up to rad/s. From to the slope is . After the slope is . At , one decade above the first pole: .
Exact value.
The asymptote error here is small because is far from both corners.
Asymptotic gain at rad/s; exact .
4.3
A series R-L-C circuit has , , . Find , , the bandwidth and the half-power frequencies.
Resonance and Q.
Bandwidth. (equal to ), which is .
Half-power frequencies.
This is a high- circuit, so the result is close to and .
, , , , .
Exercises
Practice Exercises: Transfer Function and Frequency Response
Define poles and zeros of a network function. State the condition on pole positions for stability and name the four filter types with the circuit that realises each.
Poles and zeros. Zeros are roots of the numerator of , poles are roots of the denominator. Poles are the natural frequencies of the network.
Stability. All poles must be in the left half of the -plane. A pole in the right half gives a growing response, and a repeated pole on the axis also grows.
Filters. Low-pass: RC, output across C. High-pass: CR, output across R. Band-pass: series RLC, output across R. Band-stop: series RLC, output across L and C together.
Left-half-plane poles for stability; the four filters as listed.
A CR high-pass filter has and . Find and the gain and phase at .
Cut-off. .
At . . Then
; (); phase .
For , find the poles and zeros, the dc gain, the gain at rad/s, and identify the filter type.
Zeros. gives .
Poles. gives (left half-plane, stable).
Gains. . At : numerator , denominator with magnitude , so . The gain is zero at and tends to at high frequency.
Zeros , poles , dc gain , ; a band-stop (notch) filter centred at .
For describe the Bode magnitude plot, and find the gain at rad/s.
Mid-band gain. For , and , so , that is .
Shape. Rising at below rad/s, flat at between and rad/s, then falling at . A band-pass response.
Exact at . , which is . The centre frequency is rad/s and the bandwidth is about rad/s, so : a very low-Q filter.
Mid-band gain ( at rad/s); wide band-pass with .
A series R-L-C circuit has , , . Find , , and the bandwidth, and say whether it is high-Q or low-Q.
Resonance. , so .
Q and bandwidth. and .
, , (high-Q), ().