Transformers
Open in the Padhaiko app7.1 Construction, operating principle and EMF equation of single-phase transformer
Single-Phase Transformer
A transformer is a static device that transfers electrical energy between two circuits at the same frequency, usually with a change of voltage, by mutual induction.
- Construction: two windings (primary and secondary) on a laminated silicon-steel core. In the core type the windings surround two limbs. In the shell type the windings sit on the centre limb of a three-limb core, which gives a better magnetic path. Laminations ( to ) cut eddy-current loss. Oil-immersed units use oil for insulation and cooling.
- Principle: an alternating primary current sets up an alternating flux in the core. The flux links both windings, inducing and . Hence .
EMF Equation
For a sinusoidal flux , the rms induced emf in a winding of turns is
Hence , , and the transformation ratio is
7.2 No load and load operation of transformer
No-Load Operation
With the secondary open the primary draws a small no-load current (typically to of rated), which has two components at right angles:
- Working (core-loss) component , in phase with , supplies the iron losses.
- Magnetising component , lagging by , produces the flux .
The no-load power factor is low ( to lagging).
Load Operation
When a load draws , the secondary mmf tends to reduce the flux. The primary draws an extra component that cancels it, so the core flux stays almost constant:
Because is small, . A non-ideal transformer also has winding resistances and leakage reactances from flux that links only one winding.
7.3 Equivalent circuit diagram of transformer
Equivalent Circuit
Refer all quantities to one side (say the primary) using :
- Exact circuit: in series with the parallel shunt branch ( in parallel with ), followed by and the load.
- Approximate circuit: move the shunt branch to the input terminals, then combine the series parts:
- Shunt branch: and .
7.4 Transformer testing (open circuit and short circuit)
OC and SC Tests
- Open-circuit (no-load) test: rated voltage on the LV side, HV open. The wattmeter reads the iron loss (copper loss at is negligible). , then , , , .
- Short-circuit test: low voltage on the HV side, LV shorted, until rated current flows. The wattmeter reads full-load copper loss (iron loss is negligible at the reduced flux). , , .
The two tests give the losses and the equivalent circuit without loading the transformer, so they are called indirect tests.
7.5 Voltage regulation, losses, efficiency and condition for maximum efficiency
Voltage Regulation
Use for a lagging power factor and for a leading one. Regulation can be negative for a leading load.
Losses and Efficiency
- Iron loss : constant, independent of load.
- Copper loss : varies as the square of the load. At a fraction of full load it is .
Condition for maximum efficiency: it occurs when variable loss equals constant loss, , so
7.6 Auto transformer, isolation transformer
Autotransformer and Isolation Transformer
- Autotransformer: a single winding with a tapping, part of which is common to input and output. With (step-down), the load power is and a fraction is transferred by the conductive path and the rest by transformer action. Copper saved compared with a two-winding transformer is times the copper of the two-winding unit. Advantages: smaller, cheaper, more efficient, better regulation. Disadvantage: no electrical isolation, so a fault can put the high voltage on the low side.
- Isolation transformer: turns ratio . It gives electrical isolation between the supply and the load for safety, and blocks common-mode noise and d.c.
7.1
A single-phase transformer rated , , has primary turns. Find the secondary turns, the maximum flux and the rated currents.
Turns and flux. . From :
Currents. and .
, , , .
7.2
A , transformer gives these results. OC test (LV side): , , . SC test (HV side): , , . Find the equivalent circuit constants, the regulation and the efficiency at full load pf lagging, and the maximum efficiency.
From OC test (LV side). , so and :
From SC test (HV side).
Regulation at lag. Full-load HV current :
Efficiency. Output , , :
Maximum efficiency at (load ), where :
, (LV); , (HV); regulation ; ; at .
7.3
A autotransformer supplies a load at . Find the primary, secondary and common-winding currents, the power transferred by transformer action, and the copper saving over a two-winding transformer.
Currents. and . The common section carries .
Power split. With : conducted power and transformed power .
Saving. Copper required (winding voltage current). Saving of the two-winding copper.
, , common winding ; transformed; copper saving .
Exercises
Practice Exercises: Transformers
Explain the working principle of a single-phase transformer, why its core is laminated, and compare an autotransformer with a two-winding transformer.
Principle. Alternating primary current produces an alternating flux in the core. By Faraday's law the flux induces emfs in both windings in the ratio of their turns, so . Energy passes by mutual induction, with no moving parts.
Laminations. Thin insulated sheets raise the resistance seen by eddy currents and so cut eddy-current loss. Silicon steel also lowers hysteresis loss.
Comparison. The autotransformer uses one tapped winding, so it needs less copper and iron, has lower losses and better regulation, but gives no isolation. A two-winding unit is bulkier but isolates the circuits.
Mutual induction; laminations reduce eddy loss; autotransformer is smaller and cheaper but not isolated.
A , , transformer has an emf of per turn. Find , , the maximum flux and the rated currents.
Turns. and .
Flux. so .
Currents. and .
, , , , .
A , transformer has , , , . Find the equivalent resistance and reactance referred to the HV side, the full-load copper loss and the regulation at lagging and leading.
Referred values. , so and .
Copper loss. , so .
Regulation. Lagging: . Leading: .
, , , regulation (lag) and (lead).
A transformer has iron loss and full-load copper loss . Find the full-load efficiency at pf, the load at maximum efficiency and that maximum efficiency at the same pf.
Full load. Output ; .
Maximum efficiency. , so the load is . Output and total loss :
; ; .
A autotransformer delivers to a load. Find the input, output and common-winding currents and the percentage of the power transferred by transformer action. State one use of an isolation transformer.
Currents. , , common winding .
Transformed share. , that is . The other is conducted directly.
Isolation transformer. A transformer to supply workshop test equipment safely, because the secondary is not connected to the earthed mains.
, , common ; transformed.