PadhaikoAll subjects

Diodes

Fundamental of Electrical and Electronics Engineering (ENEX 101)

Open in the Padhaiko app

4.1 Semiconductor diode characteristics

A semiconductor diode is a two-terminal nonlinear device formed by joining a -type semiconductor and an -type semiconductor ( junction). Its defining property is asymmetric conduction: it conducts readily in forward bias (anode positive with respect to cathode) and blocks current in reverse bias until breakdown.

Definition

p-n Junction Operation and Shockley Diode Equation

  1. Unbiased Equilibrium & Barrier Potential (): Diffusion of majority carriers across the junction creates a carrier-free depletion region containing uncovered immobile donor and acceptor ions, establishing a built-in barrier potential ( for silicon () and for germanium () at ).
  2. Forward Bias (): Connecting the positive terminal to the -side (anode) and negative to the -side (cathode) narrows the depletion region. Once exceeds the cut-in / knee voltage ( for , for ), current rises exponentially.
  3. Reverse Bias (): Making the -side positive widens the depletion region; only a tiny reverse saturation current ( for , for ) flows until the reverse breakdown voltage () is reached.
  4. Shockley Diode Equation: Across both forward and reverse regions (prior to breakdown), diode current obeys:

where is the reverse saturation current, is the thermal voltage, and is the ideality (emission) coefficient ( for Ge and integrated-circuit Si; for discrete Si at low currents).

4.2 Modeling the semiconductor diode

Because the Shockley equation is nonlinear and transcendental, circuit analysis replaces the diode with piecewise-linear (PWL) equivalent models for DC/large-signal circuits or a linear resistance for small AC signals.

Piecewise-Linear Semiconductor Diode Models
ModelForward-Bias Equivalent ()Reverse-Bias Equivalent ()When to Use
1. Ideal Diode ModelClosed switch ()Open switch ()Quick conceptual checks when
2. Constant Voltage Drop (Practical) ModelIdeal diode in series with battery ( Si, Ge)Open switch ()Standard hand analysis of rectifiers, clippers, clampers, logic
3. Piecewise-Linear (PWL) ModelBattery in series with forward bulk resistance ()Open switch (or large )High-current circuits where diode series drop matters

with intercepts and . Its intersection with the diode characteristic curve yields the exact -point .

4.3 Diode circuits: Clipper; Clamper circuits

Definition

Clipper (Limiter) and Clamper (DC Restorer) Circuits

  1. Clipper Circuit (Limiter): Uses diodes (and optional DC bias batteries) with a series resistor to remove (clip) a portion of an input waveform above or below a threshold level without distorting the remaining unclipped part.
    • Series Clipper: Diode is in series with the load; output drops to when the diode is reverse-biased.
    • Shunt (Parallel) Clipper: Diode (often with a series bias battery ) is in parallel across the output; when the diode conducts, output is clamped to .
    • Double / Combination Clipper (Slicer): Two anti-parallel biased diode branches clip both positive and negative peaks at independent levels.
  2. Clamper Circuit (DC Restorer): Uses a capacitor , a diode, and a load resistor to shift the entire periodic waveform vertically to a new DC level without altering its peak-to-peak amplitude.
    • Design Condition: The discharge time constant must be much larger than the half-period (, typically ), so the capacitor holds its charge between peaks.
    • Positive Clamper: Diode cathode faces ground (or bias ); during the negative input half-cycle, the capacitor charges to , shifting the output upward so its negative peak sits at (or ).
    • Negative Clamper: Diode anode faces ground; capacitor charges on the positive peak, shifting the output downward so its positive peak sits at .
AspectClipper CircuitClamper Circuit
Primary FunctionSlices off portions of the waveform exceeding a thresholdShifts the entire waveform vertically by adding a DC offset
Essential ComponentsDiode(s) + resistor (+ optional DC bias battery)Capacitor + diode + resistor (+ optional DC bias battery)
Peak-to-Peak SwingReduced (clipped peaks are removed)Unchanged ()
Typical ApplicationOver-voltage protection, pulse shaping, noise limitingRestoring DC component in TV/video and pulse receivers

4.4 Zener diode, LED, photodiode, Varactor diode, tunnel diodes

Special-purpose diodes exploit specific doping profiles, materials, or bias regions beyond simple rectification.

Special-Purpose Semiconductor Diodes
Diode TypeOperating Bias & PrincipleKey Characteristic / ParameterPrimary Applications
Zener DiodeReverse breakdown (Zener tunneling for ; Avalanche for )Nearly constant voltage over wide reverse current ( to )Voltage regulation, voltage reference, surge clipping
LED (Light Emitting Diode)Forward bias in direct-bandgap semiconductors (, , )Electroluminescence: recombination emits photons of energy ; Displays, indicators, optocouplers, solid-state lighting
PhotodiodeReverse bias (photoconductive) or zero bias (photovoltaic)Incident photons create e–h pairs in depletion region; reverse current irradianceOptical communication receivers, light meters, encoders
Varactor Diode (Varicap)Reverse bias (variable depletion width )Voltage-controlled junction capacitance RF tuning tanks, VCOs, FM modulators, PLLs
Tunnel Diode (Esaki)Forward bias with ultra-heavy doping ()Quantum tunneling creates a negative differential resistance () between and Microwave oscillators, ultra-fast picosecond switching

4.5 DC power supply: Rectifier-half wave, full wave (Center tapped, bridge), Zener regulated power supply

A linear regulated DC power supply converts AC mains into steady DC through four stages:

  1. Step-Down Transformer: Scales mains AC down to the required secondary RMS voltage and provides isolation.
  2. Rectifier: Converts bidirectional AC into unidirectional pulsating DC (half-wave or full-wave).
  3. Filter (Capacitor-Input): Smooths pulsating DC by charging to the peak and discharging slowly through load .
  4. Voltage Regulator (Zener Shunt): Maintains a constant DC output voltage despite input ripple and load changes.

Half-Wave, Center-Tapped Full-Wave, and Bridge Rectifiers

Let be the peak voltage of the secondary winding (per half-winding in a center-tapped transformer) driving a resistive load (ideal diodes, ; for practical Si diodes, replace by for HWR/CT-FWR and for Bridge FWR).

Comparison of Half-Wave, Center-Tapped, and Bridge Rectifiers (Ideal Diodes)
ParameterHalf-Wave Rectifier (HWR)Center-Tapped Full-Wave (CT-FWR)Bridge Full-Wave Rectifier
Number of Diodes (requires center-tapped secondary) (no center tap needed)
Diodes Conducting / Cycle (positive half-cycle only) per half-cycle in series per half-cycle
Peak Output () (practical: ) (practical: ) (practical: )
Average DC Output ()
RMS Output ()
Ripple Factor ()
Ripple Frequency ()
Max Rectification Efficiency ()
Peak Inverse Voltage (PIV)

Zener Regulated Power Supply

In a Zener shunt voltage regulator, an unregulated DC input feeds a series current-limiting resistor , with the reverse-biased Zener diode and load connected in parallel across the output:

For proper regulation under varying and varying :

Worked Out Examples

Example 4.1

4.1

A silicon diode is connected in series with a resistor across a DC supply. Using the piecewise-linear (PWL) model with and bulk forward resistance , find:

  1. The diode DC current and diode voltage .
  2. The small-signal AC dynamic resistance at assuming ().

Applying KVL with the PWL diode model: Replacing the forward-biased diode by a battery in series with :

Diode voltage and dynamic resistance : The total voltage drop across the PWL diode model is:

At with and :

Answer:
  1. , .
  2. .
Example 4.2

4.2

A sinusoidal input is applied to two circuits using practical silicon diodes ():

  1. Biased Shunt Clipper: A series resistor feeds output , across which is a shunt branch containing a Si diode (anode to ) in series with a battery (positive terminal to cathode, negative to ground). Determine the positive clipping level and output range.
  2. Negative Clamper: A capacitor in series with , followed by a shunt Si diode (cathode to , anode to ground) across output (with ). Determine the capacitor steady-state voltage and the clamped output peak limits.

1. Biased Shunt Clipper Analysis: The shunt diode conducts when exceeds the cathode potential () by :

  • When , the diode conducts and holds (positive peaks above are clipped).
  • When , the diode is reverse-biased (open), so down to .

2. Negative Clamper Analysis: During the positive peak (), the diode (anode at ground, cathode at ) is reverse-biased—wait: check polarity carefully! With anode at ground and cathode at :

For a negative clamper ( after charging to ):

  • At : .
  • At : .

(The peak-to-peak swing remains .)

Answer:
  1. Biased Shunt Clipper: Clips positively at ; output swings between and .
  2. Negative Clamper (anode at , cathode grounded): Capacitor charges to ; output swings between and .
Example 4.3

4.3

In a Zener diode voltage regulator, the unregulated DC input varies from to . The Zener diode has and , and the series resistor is .

  1. For a fixed load and , find the source current , load current , Zener current , and Zener power dissipation .
  2. If rises to and the load is disconnected (), check whether the Zener diode operates safely within .

Part 1 — Currents and Zener power at , : Since the open-circuit voltage divider , the Zener is in breakdown and maintains :

By KCL at the regulated node:

Part 2 — Worst-case safety check at , no load (): With no load, all source current flows through the Zener diode:

The maximum allowable Zener current is:

Since (power ), the Zener diode operates safely.

Answer:
  1. , , , .
  2. Safe: worst-case Zener current is (), below the () limit.

Exercises

Practice Exercises — Diodes

Question 1

Sketch and explain the characteristic of a silicon junction diode, clearly indicating the cut-in voltage, reverse saturation region, and breakdown region. Distinguish between Zener breakdown and Avalanche breakdown.

Regions of the Silicon Diode Characteristic:

  • Forward Bias (): Current stays negligible until the knee/cut-in voltage ( for ), then increases exponentially following .
  • Reverse Bias (): Depletion layer widens; only tiny reverse saturation current () flows.
  • Breakdown (): Reverse current increases sharply while voltage stays nearly constant at .

Zener vs. Avalanche Breakdown:

  • Zener Breakdown (): Occurs in heavily doped junctions with a narrow depletion layer; intense electric field () pulls covalent-bond electrons directly across the junction via quantum tunneling. Has a negative temperature coefficient.
  • Avalanche Breakdown (): Occurs in lightly doped junctions with a wider depletion layer; thermally generated carriers accelerate to high kinetic energy and dislodge bound electrons by impact ionization, causing carrier multiplication. Has a positive temperature coefficient.
Answer:

A Si diode conducts exponentially above , passes tiny in reverse bias, and enters steep conduction at . Zener breakdown () is caused by high-field quantum tunneling in heavily doped junctions; Avalanche breakdown () is caused by impact ionization in lightly doped junctions.

Question 2

A semiconductor diode has a reverse saturation current () and ideality factor at room temperature (). Calculate:

  1. The diode forward current when .
  2. The small-signal AC dynamic resistance at this operating point.

Forward current using the Shockley equation:

Since :

Dynamic AC resistance :

Answer:
  1. ().
  2. .
Question 3

A bridge full-wave rectifier uses four practical silicon diodes ( each) and is supplied by a (RMS), transformer secondary connected to a resistive load (no filter capacitor). Calculate:

  1. The peak secondary voltage and peak output voltage .
  2. The average DC output voltage and DC load current .
  3. The ripple frequency and required Peak Inverse Voltage (PIV) rating of each diode.

Peak secondary and peak output voltage:

In a bridge rectifier, two diodes conduct in series on each half-cycle, dropping :

Average DC output, DC current, ripple frequency, and PIV:

For a full-wave rectifier, the ripple frequency is double the mains frequency:

During peak reverse bias, each non-conducting diode sees (conservatively rated at ).

Answer:
  1. , .
  2. , .
  3. , (rated ).
Question 4

A bridge full-wave rectifier driven by a (RMS), secondary uses a filter capacitor and delivers a DC load current (assume per Si diode). Estimate:

  1. The peak-to-peak ripple voltage and RMS ripple voltage .
  2. The filtered DC output voltage .

Peak-to-peak and RMS ripple voltage: For a full-wave rectifier at , the ripple frequency is :

Assuming a triangular ripple approximation:

Filtered DC output voltage: With :

Answer:
  1. , .
  2. .
Question 5

Compare the construction, operating bias, and key applications of LED, photodiode, varactor diode, and tunnel diode.

LED and Photodiode (Optoelectronic Diodes):

  • LED: Forward-biased direct-bandgap junction; electron–hole recombination across the bandgap emits light (). Used in displays, optical transmitters, and lighting.
  • Photodiode: Reverse-biased (or zero-biased) /PIN junction with an optical window; incident photons generate electron–hole pairs swept across the depletion zone as reverse photocurrent proportional to light intensity. Used in optical receivers, light sensors, and encoders.

Varactor Diode and Tunnel Diode (Microwave / Tuning Diodes):

  • Varactor Diode: Reverse-biased diode engineered so depletion capacitance varies smoothly with reverse voltage . Used in voltage-controlled oscillators (VCOs) and FM/RF tuning circuits.
  • Tunnel Diode: Ultra-heavily doped junction ( depletion width) where quantum tunneling produces a negative differential resistance region in forward bias. Used in high-frequency microwave oscillators and fast switches.
Answer:

LED (forward-biased light emitter), Photodiode (reverse-biased light-to-current detector), Varactor (reverse-biased voltage-variable capacitor for RF tuning/VCOs), and Tunnel diode (ultra-heavily doped forward-biased diode with negative differential resistance for microwave oscillators).

← AC Circuit AnalysisTransistor (part 1: 5.1–5.3) →