PadhaikoAll subjects

Field-Effect Transistor (part 2: 2.5–2.8)

Electronic Device and Circuits (ENEX 151)

Open in the Padhaiko app

2.5 Biasing in MOS amplifier circuits

Definition

Biasing the MOSFET

A MOS amplifier must sit in saturation: . Because and vary from device to device, the bias must fix firmly. Common methods:

2.6 MOSFET circuits at DC

Definition

DC Analysis Procedure

  1. Write the gate voltage: (no gate current, so no drop across ).
  2. Write (or for drain feedback).
  3. Assume saturation: .
  4. Substituting gives a quadratic in . Choose the root that gives (the other root is false).
  5. Find and check . Otherwise the device is in the triode region and the equation must be redone with the triode current.

2.7 MOSFET as an amplifier (common source)

Definition

Common-Source Amplifier

In saturation the MOSFET is a voltage-controlled current source with small-signal model and output resistance :

For the common-source stage with the source bypassed:

With an unbypassed source resistor (and ignored):

The CS stage inverts the signal, has very high input resistance and moderate output resistance. of a MOSFET is lower than that of a BJT at the same current ().

2.8 MOSFET and CMOS as logic circuits

Definition

CMOS Inverter and Gates

In a CMOS inverter a PMOS (pull-up, source at ) and an NMOS (pull-down, source at ground) share the gate input and drain output.

CMOS Gate Structures
GatePull-down network (NMOS)Pull-up network (PMOS)Output is low when
Inverterone transistorone transistor
2-input NANDtwo in seriestwo in parallel
2-input NORtwo in paralleltwo in series or
Example 2.4

2.4

An NMOS amplifier has , , , , , and . Find , and .

Gate voltage. (no gate current).

Quadratic in . and , with :

Currents and voltages. , so and .

Since , saturation is confirmed.

Answer:

, , .

Example 2.5

2.5

A drain-feedback NMOS circuit has , , a large from drain to gate, and . Find and .

Feedback relation. No gate current, so . Then always, so saturation is automatic.

Quadratic. and :

Results. and .

Answer:

, .

Example 2.6

2.6

A CS amplifier (source bypassed) has , , , and . Find , , and .

Parameters. and .

Gain. , so

Output resistance. .

Answer:

, , .

Exercises

Practice Exercises: MOS Biasing, CS Amplifier and CMOS

Question 1

Describe the working of a CMOS inverter and explain why its static power dissipation is almost zero. Show how a 2-input NAND gate is built in CMOS.

Inverter. For input LOW the PMOS conducts and the NMOS is off, so the output is pulled to . For input HIGH the NMOS conducts and the PMOS is off, so the output is pulled to ground.

Power. In each steady state one transistor is off, so there is no DC path from to ground. Power is used only to charge and discharge the load capacitance: .

NAND. Two NMOS in series between output and ground, two PMOS in parallel between and output. Output goes low only when both inputs are high.

Answer:

Near-zero static power; NAND has series NMOS and parallel PMOS.

Question 2

A CS amplifier has , and an unbypassed source resistor (no load, ignore ). Find the voltage gain.

Gain. .

Comment. Without the gain would be . The source resistor halves the gain but makes it less dependent on .

Answer:

.

Question 3

An NMOS has gate grounded through , to , to , , . Find , and .

Gate loop. , , so . With (mA) and :

Currents and voltages. . . : saturation confirmed.

Answer:

, , .

Question 4

A CMOS inverter has , , . Find the switching threshold if (a) and (b) . If and it switches at , find the dynamic power.

(a) : .

(b) : . A stronger NMOS pulls down.

Power. .

Answer:

and ; .

Question 5

An NMOS inverter has , , , . Find the output for and for . State one disadvantage compared with CMOS.

. : transistor off, .

. . Assume triode: , which gives and

Triode is confirmed because .

Disadvantage. In the LOW state there is a DC path through , so static power is dissipated (, about ), and LOW is not exactly .

Answer:

for LOW input, for HIGH input; static power drawn in LOW output.

← Field-Effect Transistor (part 1: 2.1–2.4)Operational Amplifier Circuits and Oscillator (part 1: 3.1–3.5) →