Operational Amplifier Circuits and Oscillator (part 1: 3.1–3.5)
Open in the Padhaiko app3.1 Review of basic principles of sinusoidal oscillator
Oscillator and the Barkhausen Criterion
An oscillator produces a periodic output from d.c. power with no input signal. It is an amplifier of gain with a positive feedback network of feedback factor . Closed-loop gain: . Output exists with no input when the denominator is zero, which is the Barkhausen criterion:
that is, and total loop phase shift (or ) at one frequency only, which sets the oscillation frequency.
- At start-up the loop gain must be slightly greater than so that noise grows into oscillation.
- An amplitude-limiting mechanism (non-linear gain reduction, a lamp or diodes) brings the loop gain back to so the amplitude stays steady.
3.2 Review of Op-Amp square and triangular, RC oscillator circuits
RC Oscillators
- Wien-bridge oscillator: a series RC and a parallel RC lead-lag network (, ) gives and zero phase shift at
The non-inverting amplifier must have gain (so ), slightly larger for start-up, with a lamp or diodes to limit amplitude.
- Phase-shift oscillator: an inverting amplifier followed by three RC sections, each giving for a total of :
Op-Amp Square and Triangular Wave Generators
- Astable (relaxation) square-wave generator: an op-amp comparator with positive feedback divider , and an RC network from the output to the inverting input. The output switches between when the capacitor voltage reaches . The period is
which is for . Duty cycle is .
- Triangular generator: a Schmitt trigger (thresholds ) followed by an inverting integrator , whose output is fed back to the trigger. The integrator output ramps linearly between :
The Schmitt output is the square wave and the integrator output is the triangular wave.
3.3 LC and crystal oscillators
LC Oscillators
The frequency is set by a tank circuit and the amplifier is a BJT, FET or op-amp.
- Colpitts: the tank has one inductor and two capacitors , in series, with the junction grounded.
where is across the amplifier input (feedback side) and across its output.
- Hartley: two inductors , (tapped coil) and one capacitor: , with (neglecting ).
- LC oscillators suit radio frequencies ( to ).
Crystal Oscillator
A quartz crystal is a piezoelectric resonator with an equivalent circuit of , , in series, all in parallel with the holder capacitance . It has two resonances:
The very high ( to ) and tiny drift make crystal oscillators the choice for clocks, microprocessors and communication. Between and the crystal is inductive, so it can replace the inductor in a Colpitts or Pierce circuit.
3.4 Integrated circuit timers
The 555 Timer
The 555 contains two comparators (thresholds and ), an SR flip-flop, a discharge transistor and an output stage.
- Astable (free-running): and to the supply, capacitor charged through and discharged through :
- Monostable (one-shot): a trigger pulse below gives one output pulse of width .
3.5 Precision rectifier circuits
Precision Rectifiers (Super Diodes)
An ordinary diode rectifier ignores inputs below the diode drop (). A precision rectifier puts the diode inside the feedback loop of an op-amp, so the effective drop is reduced by the open-loop gain: (microvolts).
- Half-wave (inverting) rectifier: for the diode conducts and . For the diode is off and (the other diode or resistor clamps the op-amp so it does not saturate).
- Non-inverting half-wave (super diode): the diode follows the op-amp, and the feedback is taken from the diode cathode: for , otherwise.
- Full-wave rectifier: a half-wave stage plus a summing amplifier: (with suitable resistors). Used for ac-meter circuits, peak detectors and signal conditioning of small signals.
3.1
Design a Wien-bridge oscillator for using . Find the capacitor and the amplifier feedback resistors.
Capacitor. . The nearest standard value is , giving
Gain. The bridge attenuates by , so . With choose , slightly increased (for example a in series with a lamp) so loop gain is above at start-up.
(), , .
3.2
A 555 astable has , , . Find , , the frequency and duty cycle. Also find the pulse width of a monostable with , .
Times.
Frequency and duty cycle. , so and
Monostable. .
, , , ; monostable .
3.3
A Colpitts oscillator uses , and . Find the frequency of oscillation and the minimum amplifier gain.
Equivalent capacitance. .
Frequency.
Gain condition. so .
, .
Exercises
Practice Exercises: Oscillators, Timers and Precision Rectifiers
State the Barkhausen criterion. Why must the loop gain be slightly above unity at start-up, and how is the amplitude then stabilised? Name the oscillator preferred for (a) audio frequency, (b) radio frequency, (c) high stability.
Criterion. with loop phase shift or at the oscillation frequency.
Start-up and limiting. Noise at the right frequency is amplified only if , so it grows. As amplitude rises, a non-linear element (lamp, diodes or device saturation) reduces gain until .
Choice. (a) Wien bridge or phase-shift (RC); (b) Colpitts or Hartley (LC); (c) crystal oscillator.
; RC, LC and crystal oscillators for audio, RF and high stability.
A three-section RC phase-shift oscillator has , . Find and the minimum gain of the inverting amplifier.
Frequency. .
Gain. The three-section network attenuates by at , so . With the feedback resistor must be at least .
, .
(a) An op-amp astable multivibrator has , and . Find the period and frequency. (b) A triangular-wave generator has an integrator with , , and a Schmitt trigger with , , . Find the peak amplitude and frequency.
(a) , so and .
(b) Threshold , so the triangle is ( peak to peak). Period , so .
(a) , ; (b) , .
A crystal has , and . Find the series and parallel resonant frequencies.
Series resonance. .
Parallel resonance. .
, (about apart).
An inverting precision half-wave rectifier uses , and an op-amp of . For a peak sine wave find the peak output. Compare with an ordinary diode rectifier, and find the smallest input that turns the diode on.
Precision rectifier. For positive-going input the diode conducts, the op-amp is in a closed loop and , so the peak output is . Negative inputs give .
Ordinary diode. A silicon diode needs about , so a input produces no output.
Turn-on level. The op-amp output needs to turn the diode on, so .
Peak output ; ordinary diode gives none; turn-on near .