Operational Amplifier Circuits and Oscillator (part 2: 3.6–3.10)
Open in the Padhaiko app3.6 Bias circuits suitable for IC design
Current Source and Current Mirror
In an IC, large resistors and capacitors are costly in area, but matched transistors are cheap. Biasing therefore uses current sources copied by current mirrors.
- BJT current mirror: is diode-connected (base tied to collector) and carries . has the same , so . Including base currents,
Output resistance (high). must remain active: .
- MOS current mirror: gate current is zero, so (ideal), which also lets the mirror scale currents.
- A mirror can also source multiple copies for many stages.
3.7 The Widlar current source
Widlar Current Source
To obtain a very small current (microamperes) without a very large resistor, a resistor is placed in the emitter of the output transistor . Then and, with equal-size transistors,
Hence . The emitter degeneration also raises the output resistance, , so the source is a better constant-current source than the simple mirror.
3.8 The differential amplifier
BJT Differential Pair
Two matched transistors with joined emitters biased by a tail current (usually a current source of resistance ). Each carries at balance, so .
Input decomposition: differential and common-mode .
- Differential-mode gain (with the differential output): . With a single-ended output: .
- Differential input resistance: .
- Common-mode gain (single-ended): . Large gives small .
- Common-mode rejection ratio: (also in dB, ). High CMRR means the amplifier amplifies the difference and rejects noise common to both inputs.
An output of an op-amp input stage: . The MOS pair works the same way with -type expressions and unlimited input resistance.
3.9 Active loads
Active Load
Replacing the collector resistor by a current source or mirror gives a very large small-signal load resistance without a large DC voltage drop. Gain of a CE stage with an active load:
With equal Early voltages and the same collector current, and . It does not depend on and can reach to . In a differential amplifier with a current-mirror load, the mirror converts the differential output into a single-ended one while retaining the full gain (instead of half).
3.10 Output stages
Output Stages
The last stage of an op-amp or power amplifier must deliver the load current and power with very low output resistance, which the high-gain stages before it cannot do. The usual block is an emitter follower (class A) or a push-pull class B/AB pair, which gives a voltage gain of about , high current gain and low . The classes and their efficiencies are the topic of Chapter 4.
For a class-A emitter follower biased at with load , the maximum negative-going swing is limited to (the transistor turns off) and the positive swing to near .
3.4
(a) In a BJT current mirror and , , . Find , and the output resistance. (b) A Widlar source must provide from . Find .
(a) Mirror. . (a error from base currents). .
(b) Widlar.
A simple mirror would need a resistor of for the same .
, , ; Widlar .
3.5
A BJT differential pair has , , and a tail source with . Find , , the differential gain (differential output), the single-ended differential gain, the common-mode gain and CMRR.
Small-signal parameters. Each transistor carries : , and .
Differential gain. (differential output) or for one single-ended output.
Common-mode gain and CMRR. . For the single-ended output
, , ( single-ended), , CMRR ().
3.6
A CE amplifier has , with an active (current-source) load. The npn and pnp have . Find the gain and compare it with a resistive load.
Parameters. and .
Active load. . Check by the shortcut .
Resistive load. , ten times smaller. To obtain with a resistor, a drop of would be needed, which is impossible on a low supply.
with the active load against with .
Exercises
Practice Exercises: IC Biasing, Differential Amplifier and Active Loads
Why are current mirrors and active loads used in integrated circuits instead of resistors? List the advantages of a differential amplifier as the input stage of an op-amp.
Mirrors and active loads. Resistors take large chip area, are imprecise and drop a lot of DC voltage for a given resistance. Matched transistors on the same chip track each other with temperature, so mirrors copy currents accurately, and an active load gives a very high small-signal resistance with a small DC drop.
Differential input. It amplifies the difference of the inputs, rejects common-mode noise and drift (high CMRR), allows direct coupling (no coupling capacitors) and gives inverting and non-inverting inputs.
Matched devices, small area, high load resistance; differential pair gives high CMRR and d.c. coupling.
An NMOS mirror has and . Find . If has , and , find the resistor that sets .
Output current. .
Resistor. gives so . Then .
, .
A Widlar source with must supply from . Find and the reference resistor . What resistor would a simple mirror need for ?
Emitter resistor. .
Reference resistor. .
Simple mirror. : too large for an IC.
, ; simple mirror needs .
The differential pair of the earlier example (, , ) has inputs and . Find the magnitude of the signal and the common-mode contributions at one collector.
Input components. and .
Outputs. Wanted part: . Unwanted common-mode part: .
Comment. The common-mode input is times larger than the differential one, yet its contribution is only of the wanted output.
(signal) and (common-mode error).
A class-A emitter follower with supplies and is biased at by a current source. Find the maximum negative swing, the maximum load power for a peak sine wave and the efficiency.
Negative swing. Limited to .
Load power. .
Supply power and efficiency. The supply delivers at all times, so .
, , (poor, which motivates class B and AB in Chapter 4).