Output Stages and Power Amplifiers (part 1: 4.1–4.4)
Open in the Padhaiko app4.1 Classification of output stages
Classes of Output Stage
Output stages are classified by the conduction angle: the fraction of a signal cycle during which the output transistor carries current.
- Class A: conducts for the full . Biased at the middle of the load line. Best linearity, worst efficiency.
- Class B: each of a pair of transistors conducts for (half cycle). Zero quiescent current, but crossover distortion.
- Class AB: each transistor conducts for slightly more than (a small bias current). Removes crossover distortion with good efficiency.
- Class C: conducts for less than . Used only in tuned RF amplifiers.
| Class | Conduction angle | Quiescent current | Maximum efficiency | Distortion |
|---|---|---|---|---|
| A (resistive or current-source load) | high | very low | ||
| A (transformer-coupled) | high | very low | ||
| B (push-pull) | zero | crossover | ||
| AB | to | small | between and | low |
| C | below | zero | up to or more | high (needs tuned load) |
4.2 Class A output stage
Class A Emitter Follower
A single transistor follower with supplies , load and a constant-current source in the emitter. The output voltage is with gain close to .
- Maximum swing: positive up to near and negative down to (when the follower turns off). For symmetrical full swing, .
- For a sine output of peak : .
- The supply delivers a constant power regardless of the signal level. With and :
- The transistor dissipates the most power when there is no signal.
4.3 Class B output stage
Class B Complementary (Push-Pull) Stage
An npn follower () handles the positive half cycles and a pnp follower () the negative half cycles. For both are off, so there is a dead band in the transfer curve: crossover distortion.
For a sine output of peak , load and supplies :
Total transistor dissipation . It is maximum not at full output but at :
4.4 Class AB output stage
Class AB Stage
A small DC bias voltage is placed between the two bases, so each transistor carries a small quiescent current even at zero input. The dead band disappears, because one transistor is already almost conducting as the other turns off, and the transfer characteristic is nearly linear through zero.
- For small signals both transistors conduct (class A behaviour). For large signals only one conducts at a time (class B).
- Supply power is slightly higher than for class B: , so efficiency is a little below .
- Quiescent power is small compared with the class A value.
4.1
A class A emitter follower has supplies, and a current source. Find the maximum output swing, the maximum load power, the supply power, the efficiency and the dissipation in the transistor at no signal.
Swing. Negative limit: . Positive limit near . So .
Powers. and , so .
Dissipation at no signal. and , so : larger than the full-power load power, so the transistor must be sized for the idle condition.
swing, , , , at idle.
4.2
A class B push-pull stage has supplies and . For a sine output of peak find , , and the transistor dissipation. Find also the maximum possible and the worst-case dissipation.
Load and supply power. . per supply, so .
Efficiency and dissipation. (check ). total, each.
Limits. Maximum output gives with . Worst-case dissipation at :
, , , ; ; worst-case .
4.3
A class B follower is driven by a sine wave of peak. Taking a dead band of , what fraction of each cycle is the output zero? Why does class AB remove this problem?
Dead angle. The output is zero while . Near each zero crossing this is on each side of the crossing.
Fraction of the cycle. There are two zero crossings per cycle, each with a dead zone of , for a total of :
The effect is serious for small signals, since is a large fraction of the amplitude.
Class AB. The bases are kept apart, so each transistor is just on at and no dead band exists.
Output is zero for of each cycle; class AB removes the dead band by pre-biasing.
Exercises
Practice Exercises: Class A, B and AB Output Stages
Define the classes A, B, AB and C by conduction angle. Explain why a class B stage has the highest efficiency of the linear classes but suffers crossover distortion.
Classes. A: ; B: ; AB: between and ; C: below .
Efficiency of B. There is no quiescent current, so supply power rises only with output (), and .
Crossover. Neither transistor conducts for , so the output is flat near zero crossing. Pre-biasing (class AB) cures it.
Class B: ; crossover distortion arises from the dead band .
A transformer-coupled class A amplifier has and . Find the maximum a.c. output power, the supply power and the efficiency.
Powers. The collector voltage swings around (no DC drop in the primary) and the current swings . and .
Efficiency. , twice the resistor-loaded class A, since no DC power is wasted in a load resistor.
, , .
A class B stage has supplies and . Find the maximum output power, supply power and efficiency at full swing, and the maximum dissipation per transistor with the output amplitude at which it occurs.
Full swing. : and , so .
Worst-case dissipation. At the total is , so per transistor.
, , ; worst-case per transistor at .
A class AB stage with supplies, and a quiescent current delivers a sine of peak. Estimate the supply power and efficiency, and the quiescent power.
Supply power. Each supply gives about , so .
Efficiency. so , just below the class B value . Quiescent power is .
, , .
Compare class A and class B for delivering to (peak ) from supplies. The class A stage uses . Which dissipates less?
Class A. constant, so and the stage dissipates .
Class B. so and the dissipation is .
Class B dissipates about times less ( against ).