Geometrical Construction
Open in the Padhaiko app3.1 Plane geometrical construction: Proportional division of lines, trisection of angles, smooth arc and line tangents
Accurate mechanical drafting relies on pure compass-and-straightedge constructions to divide lines proportionally, form exact tangencies without visible kinks, and blend circular arcs smoothly into lines or adjacent arcs.
Proportional Division of a Line
To divide a given line segment AB into any number N of equal parts—or in a specified ratio such as 2 : 3 : 5—without trial-and-error measurement, apply Thales' Theorem (Similar Triangles Method):
- Draw the given line segment AB.
- From endpoint A, draw an auxiliary ray AC at a convenient acute angle (typically 20–35 degrees) below AB.
- Using dividers or a scale, step off N equal arbitrary intervals along AC (for a ratio
p : q : r, step offp + q + requal intervals), labeling the points 1, 2, 3, ..., N. - Connect the last point N directly to endpoint B with a straightedge.
- Using sliding set squares (or T-square and triangle), draw lines through points 1, 2, ..., N - 1 parallel to NB until they intersect AB. These intersections divide AB into exact equal (or proportional) segments.
Bisection and Trisection of Angles
- Bisecting an Arbitrary Angle ABC: Strike an arc centered at vertex B cutting BA at P and BC at Q. With equal radii larger than half of PQ, strike intersecting arcs from P and Q to meet at R. Line BR bisects angle ABC.
- Exact Trisection of a Right Angle (90 degrees): With vertex B as center and any convenient radius R, draw an arc cutting BA at P and BC at Q. Keeping the exact same radius R, strike an arc centered at P to cut the quadrant arc at D, and another centered at Q to cut it at E. Rays BE and BD divide the 90-degree angle into three exact 30-degree parts (since equilateral triangle chords subtend 60 degrees, leaving 90 - 60 = 30 degrees).
- Approximate Compass Trisection of an Arbitrary Acute Angle: Extend one arm BA backward past vertex B. Draw a semicircle centered at B of radius R cutting the forward arm BC at Q, the forward arm BA at P, and the backward extension at S. Using a straightedge pivoted at Q, adjust until the intercept between the semicircle (at X) and the backward line (extended from S) equals radius R (by marking R on the straightedge edge); the angle formed at the backward extension equals one-third of angle ABC.
Smooth Arc and Line Tangents
A straight line is tangent to a circle when it meets the circle at a single point of tangency (T) located on the perpendicular dropped from the circle center O onto the line (OT is perpendicular to the tangent). Two circles are tangent when their point of tangency lies on the straight line joining their centers.
Standard Tangent Construction Rules
- Tangent to a Circle from an External Point P: Join P to center O. Bisect OP at M and draw a semicircle with diameter OP. Where the semicircle cuts the circle gives exact tangent points T1 and T2 (by Thales' angle-in-semicircle = 90 degrees). Join PT1 and PT2.
- Common External (Direct) Tangent to Two Circles (Radii R1 > R2, Centers O1, O2):
- Draw an auxiliary concentric circle centered at O1 with radius (R1 - R2).
- Draw a semicircle on O1-O2 as diameter to locate tangent point K on the auxiliary circle (from O2).
- Extend ray O1-K outward to meet the outer circle R1 at T1; draw O2-T2 parallel to O1-T1 on the same side. Line T1-T2 is the common external tangent.
- Common Internal (Transverse) Tangent to Two Circles (Radii R1, R2, Centers O1, O2):
- Draw an auxiliary concentric circle centered at O1 with radius (R1 + R2).
- Draw a semicircle on O1-O2 to locate tangent point K on the auxiliary circle (from O2).
- Join O1-K, which cuts circle R1 at T1; draw O2-T2 parallel to O1-T1 on the opposite side of line O1-O2. Line T1-T2 is the common internal tangent.
- Tangent Arc of Radius R Blending Two Lines: Draw lines parallel to each given line at perpendicular offset distance R inside the angle. Their intersection locates arc center O. Drop perpendiculars from O onto both lines to find exact tangent start/stop points T1 and T2 before striking the arc.
- Tangent Arc of Radius R Blending Two Circles (Radii R1, R2):
- Externally tangent to both circles: Strike intersecting arcs centered at O1 with radius (R1 + R) and at O2 with radius (R2 + R) to locate arc center O. Locate T1 on O-O1 and T2 on O-O2 before drawing the blending arc.
- Internally enclosing both circles: Strike intersecting arcs with radii (R - R1) from O1 and (R - R2) from O2 (provided R > R1, R2); extend O-O1 and O-O2 to locate tangent points T1 and T2.
3.2 Methods for drawing regular polygons and standard curves such as ellipses, parabolas, hyperbolas, involutes, spirals, cycloids and helices (Cylindrical and conical), ogee curve
Regular Polygons
A regular polygon has N equal sides and N equal interior angles. Interior angle = ((N - 2) x 180) / N degrees, and exterior angle = 360 / N degrees.
- General Method on a Given Side AB (4–6–8 Perpendicular Bisector Method):
- Draw given side AB horizontally. At B, erect perpendicular BC = AB and join AC.
- With B as center and radius AB, swing quadrant arc AC.
- Draw the perpendicular bisector of AB; it cuts straight line AC at point 4 (center of inscribed square of side AB) and cuts arc AC at point 6 (center of regular hexagon of side AB).
- Bisect segment 4–6 to locate point 5 (center of regular pentagon). Step off the distance
4–5upward along the bisector from 6 to locate points 7, 8, 9, ... for heptagon, octagon, nonagon, etc. - To draw an N-gon, set compass center at point N with radius N–A, draw the circumcircle, and step off chord AB around the circumference.
- Semicircle Method on Given Side AB: Extend BA leftward and draw a semicircle centered at A with radius AB. Divide the 180-degree semicircle into N equal sectors (each
180 / Ndegrees), numbered 1, 2, ..., N from the leftward extension. Always draw ray A–2 as the second side of the polygon; intersect perpendicular bisectors of AB and A–2 to get the circumcenter O. - Special Inscribed Methods: For a regular hexagon of side s, the circumcircle radius equals s (step off radius 6 times around the circle). For a regular octagon inside a square of side S, draw the square's diagonals and strike arcs from all four corners with radius equal to half the diagonal (
S / sqrt(2)) to mark the 8 vertices along the square's sides.
Conic Sections (Ellipse, Parabola, Hyperbola)
Conic sections are planar curves cut by a plane intersecting a right circular cone, or defined in a plane as the locus of a point whose distance from a fixed focus (F) bears a constant ratio—called eccentricity (e)—to its perpendicular distance from a fixed directrix (DD'):
- Ellipse:
e < 1(plane cuts all generators of one nappe at an angle steeper than base, gentler than generator). - Parabola:
e = 1(plane parallel to one slant generator). - Hyperbola:
e > 1(plane cuts both nappes, steepest angle).
| Curve | Recommended Methods | Key Construction Principle |
|---|---|---|
| Ellipse | 1. Concentric Circles Method; 2. Oblong (Rectangle) Method; 3. Arcs of Circles (Foci) Method; 4. Eccentricity Method | Given major axis 2a and minor axis 2b, foci lie at distance c = sqrt(a^2 - b^2) from center (PF1 + PF2 = 2a). In Concentric Circles, draw circles of diameters 2a and 2b, draw radial rays, drop verticals from outer points and horizontals from inner points to meet on the ellipse. |
| Parabola | 1. Rectangle (Ordinate) Method; 2. Tangent Method; 3. Eccentricity Method (e = 1) | Given base width and height (or span and rise), divide half-base and side height into equal parts; draw verticals from base divisions and rays from vertex to side divisions—corresponding intersections trace the parabola. |
| Hyperbola | 1. Asymptotes Method (Rectangular Hyperbola); 2. Transverse-Conjugate / Foci Method (PF1 - PF2 = 2a); 3. Eccentricity Method (e > 1) | For a rectangular hyperbola passing through known point P(x0, y0) between perpendicular asymptotes OX, OY, draw horizontal and vertical lines through P, draw radial rays from O, and project horizontally/vertically from ray intercepts to plot curve points (x * y = constant). |
Engineering Curves: Involutes, Spirals, Cycloids, Helices, and Ogee Curve
Construction Summary of Standard Engineering Curves
- Involute: The curve traced by the free end of a taut inextensible string as it unwinds from (or winds onto) a polygon or circle.
- Circle Involute (Diameter D): Draw a circle of diameter D and divide it into 12 equal parts (1, 2, ..., 12). Draw a horizontal tangent line of length
pi * Dfrom the bottom point (12) and divide it into 12 equal parts. At each circle pointk, draw a tangent ray in the unwinding direction and step off length(k / 12) * pi * Dalong that tangent. Used directly in involute gear tooth profiles. - Normal & Tangent at point M on involute: Join M to the generating circle center O, draw a semicircle on MO to cut the circle at contact point N; MN is the exact normal, and the line perpendicular to MN at M is the tangent.
- Circle Involute (Diameter D): Draw a circle of diameter D and divide it into 12 equal parts (1, 2, ..., 12). Draw a horizontal tangent line of length
- Archimedean Spiral: The locus of a point moving outward uniformly along a radius vector while the radius vector rotates uniformly about a fixed pole O (
r = a * theta).- 1 Convolution between radii r_min and r_max: Divide the full 360-degree circle into 12 equal 30-degree radial rays, and divide the radial increment
(r_max - r_min)into 12 equal parts. Plot pointkat radiusr_min + (k / 12) * (r_max - r_min)along rayk.
- 1 Convolution between radii r_min and r_max: Divide the full 360-degree circle into 12 equal 30-degree radial rays, and divide the radial increment
- Cycloidal Curves (Circle of radius r rolling without slipping):
- Cycloid: Rolls along a straight baseline of length
2 * pi * r. Divide both circle and baseline into 12 equal parts; at each stepk, place centerC_kon the locus-of-centers line at heightrabove divisionk, and strike an arc of radiusrto cut the horizontal line projected from circle pointk. - Epicycloid: Rolls outside a fixed directing circle of radius
R. The directing arc spans central angletheta = (r / R) * 360 degrees. Center locus is an arc of radius(R + r). - Hypocycloid: Rolls inside a fixed directing circle of radius
R. Directing arc spanstheta = (r / R) * 360 degrees, and center locus has radius(R - r). (WhenR = 2r, the hypocycloid degenerates into a straight diameter!)
- Cycloid: Rolls along a straight baseline of length
- Helices (3D Space Curves Projected in 2D Views):
- Cylindrical Helix: Locus of a point moving on the surface of a right circular cylinder (diameter D) with uniform axial advance p (pitch / lead) per revolution. Divide the circular top view and one axial pitch
pin the front view into 12 equal parts; project each division vertically from the plan to the corresponding horizontal elevation line in the front view. Its true slope (helix angle) satisfiestan(alpha) = p / (pi * D). - Conical Helix: Locus of a point winding around the sloping surface of a right circular cone (base diameter D, height H) while advancing axially by pitch
pper turn. Draw 12 radial generators in both top and front views; project axial pitch steps horizontally onto the slant outline first, drop down to the radial generators in the top view (forming a spiral), or locate along the converging slant generators directly in the front view.
- Cylindrical Helix: Locus of a point moving on the surface of a right circular cylinder (diameter D) with uniform axial advance p (pitch / lead) per revolution. Divide the circular top view and one axial pitch
- Ogee (Reverse) Curve: A smooth S-shaped compound transition curve made of two circular arcs curving in opposite directions that meet at a common point of inflection (reverse tangency) to join two parallel or non-parallel straight lines smoothly (widely used in highway alignments, piping elbows, and molding profiles). To construct an ogee curve between two parallel lines separated by perpendicular distance
hwith a given longitudinal offsetL, join the two endpoint tangent points A and B, divide segment AB into two parts at inflection point M (equal parts for equal radii), erect perpendicular bisectors on AM and MB to intersect perpendiculars drawn at A and B, locating the two opposite arc centers O1 and O2.
3.3 Techniques to reproduce a given drawing (By construction)
When a Drafter must copy, enlarge, or reduce an existing drawing using only instruments (without tracing paper or a photocopier), three geometric reproduction methods guarantee exact congruence or similarity:
- Method of Triangulation (Polygon Decomposition):
- Best suited for closed polygons and irregular straight-sided templates.
- Divide the given polygon (e.g., ABCDE) into non-overlapping triangles from one corner (AC, AD).
- Draw base A'B' = AB on the new sheet. Using a compass, strike arcs of lengths AC (from A') and BC (from B') to locate C'. Repeat for triangles ACD and ADE until all vertices are transferred exactly.
- Rectangular Coordinates (Baseline / Offset Grid) Method:
- Best suited for irregular curved profiles, cams, or contours containing many non-collinear features.
- Establish two mutually perpendicular reference axes (OX and OY) touching or enclosing the original drawing.
- Drop perpendiculars from every key vertex and curve point onto OX and OY, recording
(x, y)offsets with dividers or a scale. Transfer those offsets onto a matching perpendicular axis pairO'X', O'Y'on the new sheet, and blend curves with a French curve.
- Proportional Square Grid / Radial Projection Method (for Enlarging or Reducing):
- Square Grid: Overlay a uniform grid of squares (say 10 mm x 10 mm) over the original figure, draw a scaled grid (say 20 mm x 20 mm for 2:1 enlargement) on the destination sheet, and transfer intersection crossings square by square.
- Radial Projection (Homothety): Choose a pole O inside or outside the original figure, draw rays from O through every vertex
P_i, and markP_i'along each ray at distancek * OP_i(wherekis the scale factor, e.g.,k = 1.5ork = 0.5). Connect adjacentP_i'vertices to obtain an exact scaled copy.
Worked Examples
1
Two pulleys of radii R1 = 35 mm and R2 = 15 mm have their centers 80 mm apart. Describe the exact compass-and-straightedge construction steps to draw (a) a common external (open-belt) tangent and (b) a common internal (crossed-belt) tangent, and calculate the exact tangent segment lengths between the points of tangency.
Construct the common external (direct) tangent:
- Draw center line O1-O2 = 80 mm and construct circles of radius R1 = 35 mm at O1 and R2 = 15 mm at O2.
- Centered at O1, draw an auxiliary concentric circle of radius
R1 - R2 = 35 - 15 = 20 mm. - Bisect O1-O2 at M (40 mm from O1) and draw a semicircle on O1-O2 as diameter, cutting the 20 mm auxiliary circle at K.
- Draw ray O1-K and extend it outward to meet the 35 mm circle at T1.
- Through O2, draw radius O2-T2 parallel to O1-T1 on the same side of O1-O2.
- Join T1-T2; this line is perpendicular to both radii and is the required external tangent.
- Length check: In right triangle O1-K-O2, tangent length
T1-T2 = K-O2 = sqrt(80^2 - 20^2) = sqrt(6000) = 77.46 mm.
Construct the common internal (transverse) tangent:
- Centered at O1, draw an auxiliary concentric circle of radius
R1 + R2 = 35 + 15 = 50 mm. - Use the same semicircle on diameter O1-O2 (radius 40 mm centered at M) to cut the 50 mm auxiliary circle at K'.
- Join O1-K'; this line crosses the 35 mm circle at T1'.
- Through O2, draw radius O2-T2' parallel to O1-K' on the opposite side of center line O1-O2.
- Join T1'-T2' to obtain the common internal tangent.
- Length check: In right triangle O1-K'-O2, tangent length
T1'-T2' = K'-O2 = sqrt(80^2 - 50^2) = sqrt(3900) = 62.45 mm.
External tangent uses an auxiliary circle of radius R1 - R2 = 20 mm with parallel radii on the same side (tangent length = 77.46 mm). Internal tangent uses an auxiliary circle of radius R1 + R2 = 50 mm with parallel radii on opposite sides (tangent length = 62.45 mm).
2
Give the construction sequence for: (a) An ellipse with major axis 100 mm and minor axis 60 mm using the Concentric Circles Method (also compute focal distance and eccentricity); and (b) An epicycloid generated by a rolling circle of radius r = 20 mm rolling outside a directing circle of radius R = 60 mm for one complete revolution.
(a) Ellipse by Concentric Circles Method (a = 50 mm, b = 30 mm):
- Draw major axis AB = 100 mm and minor axis CD = 60 mm bisecting each other perpendicularly at center O.
- With center O, draw two concentric circles of diameters 100 mm (radius a = 50 mm) and 60 mm (radius b = 30 mm).
- Divide both circles into 12 equal 30-degree sectors using radial rays from O (set squares 30/60 degrees). Label outer intersections 1, 2, ..., 12 and inner intersections 1', 2', ..., 12'.
- From each outer point
k, drop a short vertical line; from the corresponding inner pointk', draw a horizontal line to intersect the vertical line at ellipse pointP_k. - Connect A, P1, P2, C, P4, ..., B smoothly using a French curve.
- Foci and eccentricity:
c = sqrt(50^2 - 30^2) = sqrt(1600) = 40 mmfrom O; eccentricitye = c / a = 40 / 50 = 0.80.
(b) Epicycloid (r = 20 mm, R = 60 mm):
- Calculate the subtended angle of the directing arc for one full roll of the 20 mm circle:
theta = (r / R) x 360 = (20 / 60) x 360 = 120 degrees. - Draw a sector O-P0-P12 of radius R = 60 mm and central angle 120 degrees.
- Extend O-P0 outward by
r = 20 mmto center C0 (OC0 = R + r = 80 mm) and draw the rolling circle of radius 20 mm tangent to the directing circle at P0. - Divide the rolling circle into 12 equal parts (labeled 1, 2, ..., 12 in direction opposite to rolling, or clockwise for clockwise roll) and divide the 120-degree directing arc P0-P12 into 12 equal 10-degree sectors, projecting radial center lines to intersect the locus of centers arc (radius 80 mm) at C1, C2, ..., C12.
- Swing concentric arcs centered at O through circle points 1, 2, ..., 11. From each center
C_k, cut the corresponding concentric arckwith compass radius r = 20 mm to locate epicycloid points. Join with a French curve.
(a) The Concentric Circles Method projects verticals from the 100 mm circle and horizontals from the 60 mm circle along 12 radial rays (c = 40 mm, e = 0.80). (b) The Epicycloid spans a directing arc of 120 degrees at radius 60 mm, with center locus at radius 80 mm divided into 12 ten-degree steps.
3
Explain the construction steps to draw one complete turn of a Cylindrical Helix on a cylinder of diameter D = 60 mm with axial pitch p = 48 mm. Compute the helix angle and the true developed length of one turn of the helical curve.
Compute true helix length and helix angle:
- Circumference of cylinder =
pi x D = 3.14159 x 60 = 188.50 mm. - Unwrapping one turn of the cylinder onto a flat plane produces a right triangle of base
188.50 mmand heightp = 48 mm. - True length of 1 helical turn =
sqrt(188.50^2 + 48^2) = sqrt(35530.58 + 2304) = 194.51 mm. - Helix slope angle:
tan(alpha) = 48 / 188.50 = 0.25465, givingalpha = 14.29 degrees.
Graphical construction steps (Top + Front views):
- Draw the top view as a 60 mm diameter circle and divide it into 12 equal 30-degree parts (points 0, 1, 2, ..., 12).
- Directly above, project the front view rectangle of width 60 mm and height p = 48 mm. Divide the 48 mm height into 12 equal horizontal intervals of 4 mm each, drawing light horizontal lines across the front view.
- Project vertical lines upward from circle points 0, 1, 2, ..., 12 in the top view to intersect the corresponding horizontal height lines 0, 1, 2, ..., 12 in the front view.
- Trace a smooth curve through points 0–6 as a visible solid curve (front half of the cylinder) and points 6–12 as a dashed hidden curve (back half of the cylinder).
Project 12 equal angular divisions from the 60 mm plan circle upward onto 12 equal 4 mm elevation steps across the 48 mm pitch (front half solid, back half dashed). True length of one turn = 194.51 mm, helix angle = 14.29 degrees.
Exercises
Exercises
Describe the step-by-step compass-and-straightedge construction to: (a) Divide a 95 mm straight line into 7 equal parts using Thales' method; and (b) Trisect a 90-degree angle geometrically using only a compass and straightedge.
(a) Dividing a 95 mm line AB into 7 equal parts:
- Draw segment AB = 95 mm horizontally.
- From A, draw an auxiliary ray AC downward at an acute angle (about 30 degrees).
- Set dividers to a convenient step (e.g., 12 mm) and step off 7 equal intervals along AC, labeled 1 through 7.
- Connect point 7 directly to B with a straightedge.
- Slide a set square along a stationary second set square (or T-square) to draw lines through points 6, 5, 4, 3, 2, 1 parallel to 7–B. Their intersections with AB divide AB into 7 exact equal segments (each 13.57 mm).
(b) Trisecting a 90-degree angle ABC:
- With vertex B as center and any convenient radius R, draw a quadrant arc cutting arm BA at P and arm BC at Q.
- Keeping the exact same compass radius R, place the needle at P and strike an arc cutting the quadrant arc at D.
- Keeping radius R, place the needle at Q and strike an arc cutting the quadrant arc at E.
- Join B–E and B–D. Because chord BD = R forms an equilateral triangle with B and P (60 degrees), angle CBD = 90 - 60 = 30 degrees; similarly angle ABE = 30 degrees, leaving middle angle EBD = 30 degrees.
(a) Lay off 7 equal arbitrary steps along an acute ray from A, join step 7 to B, and project parallels back to AB. (b) Swing equal-radius arcs from both arms P and Q of the quadrant arc to cut the arc at E and D, creating three exact 30-degree sectors.
Two circles have radii R1 = 30 mm and R2 = 45 mm with centers 90 mm apart. Explain the construction to draw an external blending arc of radius R = 20 mm tangent smoothly to both circles externally, and specify the exact compass radii used to locate the arc center and how to find the exact tangency endpoints.
Locate the blending arc center O:
- Draw center line O1-O2 = 90 mm and construct the two circles (radius 30 mm at O1, radius 45 mm at O2).
- For an arc externally tangent to circle O1, the center distance must equal
R1 + R = 30 + 20 = 50 mm. Strike an arc of radius 50 mm centered at O1. - For an arc externally tangent to circle O2, the center distance must equal
R2 + R = 45 + 20 = 65 mm. Strike an arc of radius 65 mm centered at O2 to intersect the first arc at O (two symmetric solutions exist, one above and one below O1-O2).
Locate exact tangency points and draw the arc:
- Join straight line O–O1; its intersection with circle O1 is tangent point T1.
- Join straight line O–O2; its intersection with circle O2 is tangent point T2.
- Place compass needle at O with radius 20 mm and draw the blending arc strictly from T1 to T2 so the transition has zero kink or overlap.
Strike intersecting arcs of radius 50 mm (30 + 20) from O1 and 65 mm (45 + 20) from O2 to locate center O. Connect O–O1 and O–O2 to mark exact tangency points T1 and T2, then draw the 20 mm arc between T1 and T2.
Compute the interior angle of a regular pentagon (5 sides) and a regular hexagon (6 sides), and the exterior angle of a regular octagon (8 sides). Describe the 4–6–8 Perpendicular Bisector Method to construct a regular pentagon on a given base edge AB = 40 mm.
Compute polygon angles:
- Regular pentagon (N = 5) interior angle =
((5 - 2) x 180) / 5 = 540 / 5 = 108 degrees. - Regular hexagon (N = 6) interior angle =
((6 - 2) x 180) / 6 = 720 / 6 = 120 degrees. - Regular octagon (N = 8) exterior angle =
360 / 8 = 45 degrees.
Construct the regular pentagon on AB = 40 mm (4–6–8 method):
- Draw AB = 40 mm horizontally. At B, erect perpendicular BC = 40 mm and join diagonal AC.
- With center B and radius BA = 40 mm, draw quadrant arc AC.
- Construct the perpendicular bisector of AB; mark its intersection with straight line AC as 4 and with arc AC as 6.
- Bisect segment 4–6 on the perpendicular bisector to locate point 5 (center of the circumscribed circle for a pentagon).
- With compass center at 5 and radius 5–A, draw the circumcircle. Set dividers to 40 mm (length AB) and step off four consecutive chords around the circle from A and B to complete the regular pentagon.
Pentagon interior angle = 108 degrees; hexagon interior angle = 120 degrees; octagon exterior angle = 45 degrees. In the 4–6–8 method, locate point 5 midway between line-intersection 4 and arc-intersection 6 on the perpendicular bisector of AB, draw the circumcircle of radius 5–A, and step off 40 mm chords.
Define eccentricity (e) of a conic section and state the value ranges of e for an ellipse, parabola, and hyperbola. Also describe how to construct one complete involute of a circle of diameter 40 mm, stating the total unwound string length and how to draw the normal and tangent at any point on the involute.
Eccentricity definition and classification: Eccentricity e is the constant ratio (Distance from Focus F) / (Perpendicular Distance from Directrix DD'):
- Ellipse:
0 < e < 1(for example, 25 / 35 = 0.714). - Parabola:
e = 1(for example, 25 / 25 = 1.0). - Hyperbola:
e > 1(for example, 25 / 15 = 1.667).
Circle involute construction (D = 40 mm) and normal/tangent:
- Total unwound length for 1 revolution =
pi x D = pi x 40 = 125.66 mm. - Draw the 40 mm circle, divide it into 12 equal parts (1, 2, ..., 12), and draw a baseline tangent of length 125.66 mm at the bottom point (12), also divided into 12 equal intervals (each
10.47 mm). - At each circle point
k, draw a forward tangent line and step offktwelfth-intervals (k x 10.47 mm) along it to plot points P1 through P12; join smoothly with a French curve. - Normal and tangent at any curve point M: Join M to circle center O, draw a semicircle on diameter MO cutting the base circle at N. Line MN is the normal, and the perpendicular to MN at M is the tangent.
Eccentricity e = PF / PM gives an ellipse (e < 1), parabola (e = 1), or hyperbola (e > 1). For a 40 mm circle involute, unwind 125.66 mm tangentially across 12 equal steps; the normal at point M joins M to the tangent point N on the circle located via a semicircle on MO.
Compare the Triangulation Method, Rectangular Coordinates Method, and Proportional Square Grid Method for reproducing an existing drawing by geometric construction. Identify which method is best suited for: (a) a straight-edged irregular pentagon, (b) a cam profile with curved lobes, and (c) enlarging a complex contour 2x.
Compare the three reproduction methods:
- Triangulation Method: Divides a straight-sided figure into triangles from one vertex and copies triangle side lengths with a compass. Exact and fast for polygonal shapes, unsuitable for smooth curves.
- Rectangular Coordinates Method: Establishes perpendicular X–Y axes and transfers perpendicular
(x, y)offsets of vertices and closely spaced curve points using dividers. Accurate for both straight edges and arbitrary curves at 1:1 scale. - Proportional Square Grid Method: Overlays a uniform square grid on the source drawing and transfers curve intersections onto a scaled square grid (
2xlarger squares for 2:1 enlargement) on the new sheet.
Match each scenario to the best method:
- (a) Straight-edged irregular pentagon: Triangulation Method (decomposes into 3 triangles copied directly by compass arcs).
- (b) Cam profile with curved lobes (same size): Rectangular Coordinates Method (captures radial/curved points accurately from X–Y datums).
- (c) Enlarging a complex contour 2x: Proportional Square Grid Method (or radial homothety from a pole at 2x ray lengths).
Use Triangulation for straight-sided polygons (a), Rectangular Coordinates for 1:1 curved cam profiles (b), and the Proportional Square Grid (or radial projection) for scaling a complex contour by 2x (c).