PadhaikoAll subjects

Basic Descriptive Geometry

Engineering Drawing (ENME 101)

Open in the Padhaiko app

4.1 Introduction to orthographic projection, principal planes, four quadrants or angles

Descriptive geometry is the graphical science of representing three-dimensional points, lines, planes, and solids accurately on a two-dimensional sheet and solving spatial geometric problems (true lengths, angles, clearances, intersections) purely by construction.

Orthographic Projection and Principal Planes

Orthographic projection projects points onto a Plane of Projection using parallel projectors oriented perpendicular (90 degrees) to the plane. Two mutually perpendicular Principal Planes of Projection divide 3D space into four quadrants (dihedral angles):

The Four Quadrants (Dihedral Angles) and Unfolded View Positions
QuadrantPosition of ObjectFront View (on VP)Top View (on HP after CW rotation)Practical Usage
First Quadrant (I)Above HP, In front of VPAbove XYBelow XYFirst Angle Projection (ISO / Institute of Engineering standard)
Second Quadrant (II)Above HP, Behind VPAbove XYAbove XYNot used in working drawings (views overlap)
Third Quadrant (III)Below HP, Behind VPBelow XYAbove XYThird Angle Projection (US / ASME standard)
Fourth Quadrant (IV)Below HP, In front of VPBelow XYBelow XYNot used in working drawings (views overlap)

4.2 Projection of points on first, second, third and fourth quadrants

In standard descriptive geometry notation (Bhatt / Luintel / Luzadder):


4.3 Projection of lines: Parallel to one of the principal planes, inclined to one of the principal plane and parallel to other, Inclined to both principal planes, traces of a line

A straight line AB is completely determined by projecting its two endpoints A (a', a) and B (b', b). Let TL be true length, theta be true inclination to HP, and phi be true inclination to VP.

Orthographic Projections of Straight Lines in Standard Positions
Spatial OrientationFront View (a'b')Top View (ab)Key Property
1. Parallel to both HP and VPParallel to XY, True Length (TL)Parallel to XY, TLBoth views show true length
2. Perpendicular to HP (parallel to VP)Perpendicular to XY, TLReduces to a single point (a(b))Top view is point view
3. Perpendicular to VP (parallel to HP)Reduces to a single point (a'(b'))Perpendicular to XY, TLFront view is point view
4. Parallel to VP, inclined to HP at thetaInclined at theta to XY, TLParallel to XY, foreshortened (TL cos theta)Elevation shows TL & theta
5. Parallel to HP, inclined to VP at phiParallel to XY, foreshortened (TL cos phi)Inclined at phi to XY, TLPlan shows TL & phi
6. Inclined to both HP (theta) and VP (phi)Inclined at apparent angle alpha (> theta), foreshortenedInclined at apparent angle beta (> phi), foreshortenedNeither view shows TL directly; note theta + phi <= 90 deg

Traces of a Line


4.4 Projection planes: Perpendicular to both principal planes, parallel to one of the principal planes and Inclined to one of the principal planes, perpendicular to other and Inclined to both principal planes

A plane (lamina such as a triangle, rectangle, pentagon, or circle) is classified by its orientation relative to HP and VP:

  1. Plane Perpendicular to Both HP and VP (Profile Plane): Both its front view and top view are straight lines perpendicular to XY (edge views). Its true shape appears only in the side (profile) view.
  2. Plane Parallel to One Principal Plane (and Perpendicular to the Other):
    • Parallel to HP (Horizontal Plane): Top view shows True Shape; front view is a horizontal line parallel to XY.
    • Parallel to VP (Frontal Plane): Front view shows True Shape; top view is a horizontal line parallel to XY.
  3. Plane Inclined to One Principal Plane and Perpendicular to the Other (Auxiliary Inclined / Vertical Planes):
    • Perpendicular to VP, inclined to HP at theta (AIP): Front view is a single straight line inclined at theta to XY (edge view); top view is foreshortened.
    • Perpendicular to HP, inclined to VP at phi (AVP): Top view is a single straight line inclined at phi to XY (edge view); front view is foreshortened.
  4. Plane Inclined to Both HP and VP (Oblique Plane): Neither the front view nor the top view shows an edge view or true shape directly; both views appear as foreshortened polygons. Solved by Change of Position (3-stage rotation) or Auxiliary View Method.

4.5 True length of lines: Horizontal, inclined and oblique lines

  1. Horizontal / Frontal / Profile Lines: If a line is parallel to VP, its front view a'b' is already its True Length (TL). If parallel to HP, its top view ab is already its TL. If it is a profile line (parallel to PP, perpendicular to XY in both FV and TV), its TL appears in the side view or by rotating it parallel to VP/HP.
  2. Oblique Lines (Inclined to Both HP and VP): Two standard methods recover TL, theta, and phi:
    • Rotation (Trapezoid / Cone-Generator) Method:
      • Hold a fixed and swing top view ab horizontally to ab1 parallel to XY; project b1 vertically up to the horizontal locus line through b' at b1'. Segment a'b1' equals TL, and its angle with XY is theta (inclination to HP).
      • Similarly, hold a' fixed, swing a'b' horizontally to a'b2' parallel to XY, drop vertically to the horizontal locus through b at b2. Segment ab2 equals TL, and its angle with XY is phi (inclination to VP).
    • Auxiliary Plane Method: Draw an auxiliary folding line X1Y1 parallel to top view ab (or front view a'b'). Transfer heights (z-distances from XY in FV) perpendicularly from X1Y1 to obtain a1'b1', which shows TL and inclination theta directly.

4.6 Rules for parallel and perpendicular lines


4.7 Point view or end view of a line

To see a straight line AB as a single point (its Point View or End View), the line of sight must look directly along the axis of the line—meaning the new projection plane must be perpendicular to the True Length of AB:

  1. If AB is not already shown in True Length, construct a primary auxiliary view (View 1) across a folding line X1Y1 parallel to AB in either the top or front view so that a1'b1' shows TL.
  2. Draw a secondary folding line X2Y2 perpendicular (90 degrees) to the True Length view a1'b1'.
  3. Project from a1' and b1' along the direction of TL across X2Y2, transferring the perpendicular distance d from the previous folding line X1Y1 (which is identical for both A and B because X1Y1 was parallel to ab). Both endpoints project to the exact same location a2(b2)—the point view of line AB.

4.8 Shortest distance from a point to a line

The shortest distance from a spatial point P to a line AB is the length of the perpendicular dropped from P onto AB. Two standard descriptive geometry constructions find it:


4.9 Edge view and true shape of an oblique plane

An oblique plane (triangle ABC) shows neither an edge nor its true shape in the principal views. Finding both takes two successive auxiliary views (or two rotations):

  1. Step A — Edge View (Primary Auxiliary View):
    • Draw a horizontal line a'h' inside the plane in the Front View (a'h' parallel to XY, cutting b'c' at h').
    • Project h' down to bc in the Top View to locate h. Line ah in the Top View is in True Length!
    • Draw primary folding line X1Y1 perpendicular to the True Length line ah.
    • Project A, B, C across X1Y1, transferring heights (z) from the Front View. Because ah projects as a point, all three points a1', b1', c1' align on a single straight line—the Edge View of plane ABC (and its angle with X1Y1 is the true dip/slope angle of the plane with HP).
  2. Step B — True Shape (Secondary Auxiliary View):
    • Draw secondary folding line X2Y2 parallel to the Edge View a1'b1'c1'.
    • Project a1', b1', c1' perpendicularly across X2Y2, transferring distances from X1Y1 measured in the Top View (ab, ac).
    • Triangle a2 b2 c2 shows the exact True Shape and True Area of the oblique plane.

4.10 Angle between two intersecting lines

Two intersecting lines AB and BC (meeting at vertex B in both FV and TV on a vertical projector) define a plane ABC. The true angle at B cannot be measured in FV or TV unless both legs lie parallel to that projection plane.


4.11 Intersection of a line and a plane, visible portion of line

Finding where a line PQ pierces an oblique plane ABC (without needing auxiliary views) uses the Cutting Plane (Edge-View Line) Method:

  1. Pass a Vertical Cutting Plane through Line PQ: In the Top View, treat line pq as the edge view of a vertical auxiliary cutting plane. Mark where pq crosses edges of triangle abc in the Top View (say at 1 on ab and 2 on bc).
  2. Project the Line of Intersection to the Front View: Project 1 vertically up to a'b' (1') and 2 up to b'c' (2'). Join 1'–2'; this is the line of intersection between the vertical cutting plane and plane ABC.
  3. Locate the Piercing Point (I): In the Front View, the intersection of 1'–2' with p'q' locates i', the Front View of the piercing point. Project i' vertically down onto pq to locate i in the Top View.
  4. Determine Visibility of Line PQ:
    • Look at an apparent crossing point in the Top View (say where pq crosses ac). Project down/up from that crossing to the Front View: whichever segment (pq or ac) has the higher elevation (greater z above XY) in the Front View is above the other and therefore visible in the Top View; the segment on the other side of piercing point i goes below the plane and is hidden (dashed) inside the triangle boundary.
    • Look at an apparent crossing point in the Front View and check the Top View: whichever segment is farther below XY (more in front of VP) is in front and visible in the Front View; the portion behind the plane inside the triangle boundary is hidden.

4.12 Angle between a line and a plane

The angle between a line PQ and a plane ABC is the angle between PQ and its orthogonal projection onto plane ABC (equivalently, 90 degrees - angle(PQ, normal to ABC)). Two auxiliary views recover it directly:

  1. Obtain the Edge View of plane ABC (a1'b1'c1') and simultaneously project line p1'q1'.
  2. Obtain the True Shape of plane ABC (a2 b2 c2) across X2Y2 parallel to a1'b1'c1', carrying line p2 q2 with it.
  3. Draw a third folding line X3Y3 parallel to p2 q2. Because View 2 shows plane ABC in True Shape, any plane perpendicular to View 2 automatically displays plane ABC as an Edge View, while placing line p3 q3 in True Length simultaneously.
  4. The acute angle measured directly between True-Length line p3 q3 and the Edge View of plane ABC (a3 b3 c3) is the exact true angle between the line and the plane.

4.13 Dihedral angle between two planes

The dihedral angle between two intersecting planes (such as two adjacent roof faces or faces of a bracket sharing a common line of intersection AB) is the angle seen when looking directly along their line of intersection AB:

  1. Locate (or construct) the line of intersection AB common to both planes.
  2. Draw primary folding line X1Y1 parallel to ab (or a'b') and project both planes and line AB into View 1 so a1'b1' appears in True Length.
  3. Draw secondary folding line X2Y2 perpendicular to True Length a1'b1', and project all vertices of both planes into View 2.
  4. In View 2, the line of intersection projects as a single point a2(b2), so both planes automatically appear as straight Edge Views meeting at a2(b2). The angle measured directly between these two edge-view lines is the exact Dihedral Angle.

4.14 Shortest distance between two skew lines

Two lines AB and CD in 3D space are skew lines if they are neither parallel nor intersecting (their apparent crossing points in FV and TV do not align on a common vertical projector). The shortest distance (common perpendicular) between two skew lines is found cleanly by the Point-View (Line) Method:

  1. Draw X1Y1 parallel to one line (say ab in TV) and project both AB and CD into View 1 so a1'b1' shows True Length.
  2. Draw X2Y2 perpendicular to a1'b1' and project both lines into View 2. Here AB appears as a single point a2(b2), while CD appears as c2 d2.
  3. In View 2, drop a perpendicular directly from point a2(b2) onto line c2 d2 at foot n2. The measured length a2(b2) – n2 is the exact True Shortest Distance between the two skew lines!
  4. To locate the common perpendicular MN in the principal views: project n2 back across X2Y2 onto c1'd1' (n1'). Because MN is perpendicular to AB (which appears as a point in View 2), MN appears in True Length in View 2 and lies parallel to X2Y2 (perpendicular to a1'b1') in View 1. Draw n1' m1' perpendicular to a1'b1' to locate m1', then project both m1', n1' back into TV and FV.

4.15 Angle between two non-intersecting (Skew) lines

The angle between two skew lines AB and CD is defined as the angle between CD and a line CE drawn through C parallel to AB (forming intersecting lines CD and CE). Two auxiliary views or the parallel-translation method determine it:

  1. Parallel-Translation + True-Shape Method: Through endpoint c in TV and c' in FV, draw ce parallel to ab and c'e' parallel to a'b' (making CE equal and parallel to AB). Lines CD and CE now intersect at C and define plane CDE. Find the Edge View and True Shape of triangle CDE; the angle measured at d2–c2–e2 is the angle between skew lines AB and CD.
  2. Direct Auxiliary Method: Project both skew lines onto a plane where both lines appear in True Length simultaneously (first get a1'b1' TL, then a2(b2) point view, then project across X3Y3 parallel to c2 d2—in View 3, c3'd3' is TL and a3'b3' is also parallel to View 3 since it was a point in View 2, so both lines are in True Length and their crossing angle is the exact angle between the skew lines!).

Worked Examples

Example 1

1

A line AB lies in the First Quadrant with endpoint A located 15 mm above HP and 20 mm in front of VP. Endpoint B is 55 mm above HP, 50 mm in front of VP, and the distance between the end projectors (along XY) is 50 mm. Using the Rotation Method, explain how to draw the projections of AB and determine its True Length (TL) and true inclinations theta (to HP) and phi (to VP), plus its traces (HT and VT).

Plot the endpoints A and B relative to XY:

  • Point A (1st quadrant): a' is 15 mm above XY, a is 20 mm below XY on the left projector.
  • Point B (1st quadrant): move 50 mm right along XY; b' is 55 mm above XY, b is 50 mm below XY.
  • Join a'b' (Front View, apparent length = sqrt(50^2 + 40^2) = 64.03 mm) and ab (Top View, apparent length = sqrt(50^2 + 30^2) = 58.31 mm).

Determine True Length and true inclinations by Rotation:

  1. Find TL and theta (to HP): Hold a fixed and swing top view ab (radius 58.31 mm) into a horizontal position ab1 parallel to XY (b1 is 20 mm below XY, 58.31 mm right of a). Project b1 vertically upward to intersect the horizontal locus line through b' (55 mm above XY) at b1'. Join a'b1':
    • TL = sqrt(50^2 + 40^2 + 30^2) = sqrt(5000) = 70.71 mm.
    • Angle of a'b1' with XY gives theta = arcsin(40 / 70.71) = 34.45 degrees.
  2. Find TL and phi (to VP): Hold a' fixed and swing front view a'b' (radius 64.03 mm) horizontal to a'b2' parallel to XY. Drop vertically down to intersect the horizontal locus line through b (50 mm below XY) at b2. Join ab2:
    • ab2 confirms TL = 70.71 mm, and its angle with XY gives phi = arcsin(30 / 70.71) = 25.10 degrees.

Locate Horizontal Trace (HT) and Vertical Trace (VT):

  • Extend front view b'a' downward-left until it meets XY at h'. Drop a vertical projector from h' to intersect extended top view ba at HT (above XY in this geometry since a' is closer to XY than b', specifically h' lies 15 * (50/40) = 18.75 mm left of a).
  • Extend top view ba upward-left until it meets XY at v. Erect a vertical projector from v to intersect extended front view b'a' at VT.
Answer:

True Length TL = 70.71 mm; inclination to HP theta = 34.45 degrees; inclination to VP phi = 25.10 degrees. Front view a'b' = 64.03 mm and top view ab = 58.31 mm; HT and VT are located by extending one view to XY and projecting perpendicularly onto the extended opposite view.

Example 2

2

Explain the step-by-step Auxiliary View procedure to determine the Edge View and True Shape of an oblique triangular lamina ABC given in Front View (a'b'c') and Top View (abc), and to measure the shortest distance from an external point P (p', p) to a skew/oblique line AB (a'b', ab).

Part A — Edge View and True Shape of oblique triangle ABC:

  1. Draw a horizontal line in the Front View through one vertex (say a'h' parallel to XY, meeting b'c' at h').
  2. Project h' vertically down to bc in the Top View to mark h. Line ah is now a True-Length horizontal line inside plane ABC.
  3. Draw folding line X1Y1 perpendicular to ah (and clear of the Top View).
  4. Project a, b, and c perpendicularly across X1Y1. Measure the vertical heights (z_A, z_B, z_C) from XY to a', b', c' in the Front View and transfer them along the respective projectors past X1Y1. Points a1', b1', c1' align on a straight line—the Edge View of ABC.
  5. Draw secondary folding line X2Y2 parallel to Edge View a1'b1'c1'. Project a1', b1', c1' across X2Y2 and transfer distances measured from X1Y1 in the Top View. Triangle a2 b2 c2 is the exact True Shape.

Part B — Shortest distance from point P to line AB (with numerical coordinate check example):

  1. Draw X1Y1 parallel to ab in the Top View and project both ab and p into View 1 using z-heights from the Front View; a1'b1' shows True Length.
  2. Draw X2Y2 perpendicular to a1'b1' and project AB and P into View 2 using distances from X1Y1 in the Top View. AB collapses to a point view a2(b2).
  3. Measure segment a2(b2) – p2 directly in View 2; this is the True Shortest Distance. (For instance, in a coordinate test where line AB passes along 3x - 4y = 0 in View 2 and P projects to (40, 10), the perpendicular distance is |3(40) - 4(10)| / 5 = 80 / 5 = 16.0 mm.)
Answer:

For Edge View & True Shape: construct one True-Length horizontal line ah in the plane, take View 1 perpendicular to ah (giving Edge View), then View 2 parallel to the Edge View (giving True Shape). For Point-to-Line Shortest Distance: take View 1 parallel to AB (TL), then View 2 perpendicular to TL (point view of AB), and measure directly from a2(b2) to p2.

Example 3

3

Describe how to find the piercing point (I) and visibility of a line PQ passing through an oblique triangular plane ABC using the Vertical Cutting Plane Method (without auxiliary views), and explain how to find the dihedral angle between two intersecting planes ABC and ABD.

Part A — Piercing point and visibility of line PQ with plane ABC:

  1. Vertical Cutting Plane: In the Top View, consider pq to represent the edge view of a vertical plane. Mark intersections 1 (where pq crosses ab) and 2 (where pq crosses bc).
  2. Project intersection line 1'–2': Project 1 upward to a'b' (1') and 2 upward to b'c' (2'). Connect 1'–2' in the Front View.
  3. Locate Piercing Point: Where 1'–2' crosses p'q' in the Front View is i'. Drop a vertical projector from i' onto pq to mark i in the Top View.
  4. Determine Visibility:
    • Check where pq crosses ac in the Top View: project to the Front View—whichever edge (p'q' or a'c') is higher above XY is visible on that side of i in the Top View; the portion of pq on the opposite side of i inside abc is hidden (dashed).
    • Check where p'q' crosses a'c' in the Front View: project down to the Top View—whichever edge (pq or ac) is farther below XY (more in front) is visible on that side of i' in the Front View; the remainder inside a'b'c' is hidden (dashed).

Part B — Dihedral angle between planes ABC and ABD:

  1. Identify the common line of intersection AB (a'b', ab).
  2. Draw primary folding line X1Y1 parallel to ab and project all four points A, B, C, D into View 1 using heights from XY in FV. Segment a1'b1' is now in True Length.
  3. Draw secondary folding line X2Y2 perpendicular to a1'b1' and project A, B, C, D into View 2 using distances from X1Y1 in TV.
  4. Both A and B coincide at point a2(b2), so both planes appear as straight Edge Views a2(b2)–c2 and a2(b2)–d2. Measure the angle directly between these two rays to get the dihedral angle.
Answer:

Piercing point: treat pq as a vertical cutting plane in TV, project its cut across abc to 1'–2' in FV to intersect p'q' at i', then test crossing points in the adjacent view for elevation/frontness to assign dashed hidden segments. Dihedral angle: take View 1 parallel to common edge AB (TL) and View 2 perpendicular to a1'b1' (Point View of AB), where both planes become lines meeting at the exact dihedral angle.


Exercises

Exercises

Question 1

Determine the quadrant (I, II, III, or IV) and exact positions of the Front View (p') and Top View (p) relative to the XY reference line for each of the following points:

  1. Point A: 25 mm above HP, 35 mm in front of VP
  2. Point B: 30 mm above HP, 20 mm behind VP
  3. Point C: 15 mm below HP, 40 mm behind VP
  4. Point D: 20 mm below HP, 25 mm in front of VP
  5. Point E: on HP, 30 mm in front of VP

Apply the quadrant and 90-degree clockwise HP rotation rules:

  1. Point A (1st Quadrant): Above HP -> a' is 25 mm above XY; In front of VP -> a rotates down 35 mm below XY.
  2. Point B (2nd Quadrant): Above HP -> b' is 30 mm above XY; Behind VP -> b rotates up 20 mm above XY (both views above XY).
  3. Point C (3rd Quadrant): Below HP -> c' is 15 mm below XY; Behind VP -> c rotates up 40 mm above XY.
  4. Point D (4th Quadrant): Below HP -> d' is 20 mm below XY; In front of VP -> d rotates down 25 mm below XY (both views below XY).
  5. Point E (Boundary of I and IV, on HP): On HP -> e' lies directly on XY; In front of VP -> e is 30 mm below XY.
Answer:
  1. A (Q-I): a' 25 mm above XY, a 35 mm below XY. 2. B (Q-II): b' 30 mm above XY, b 20 mm above XY. 3. C (Q-III): c' 15 mm below XY, c 40 mm above XY. 4. D (Q-IV): d' 20 mm below XY, d 25 mm below XY. 5. E (on HP): e' on XY, e 30 mm below XY.
Question 2

A straight line AB, 80 mm long, has its endpoint A 15 mm above HP and 20 mm in front of VP. The line is inclined at 30 degrees to VP, and its front view has a projected length corresponding to a height difference of 35 mm between B and A (with B above A and farther in front of VP). Compute the True inclination theta to HP, the Top View length, and the Front View length, and explain how to draw the projections.

Compute true inclination theta to HP and Top View length:

  • Height difference dz = 35 mm and True Length TL = 80 mm.
  • sin(theta) = dz / TL = 35 / 80 = 0.4375, so theta = arcsin(0.4375) = 25.94 degrees.
  • Top View length ab = TL x cos(theta) = sqrt(80^2 - 35^2) = sqrt(5175) = 71.94 mm.

Compute Front View length and construction sequence:

  • Inclination to VP is phi = 30 degrees, so Front View length a'b' = TL x cos(30 deg) = 80 x 0.8660 = 69.28 mm.
  • Distance B is farther in front of VP than A: dy = TL x sin(30 deg) = 80 x 0.5 = 40.0 mm (so B is 20 + 40 = 60 mm in front of VP, and 15 + 35 = 50 mm above HP).
  • Construction: Plot a' (15 mm above XY) and a (20 mm below XY). Draw locus lines b' (50 mm above XY) and b (60 mm below XY). Swing a'b1' = 80 mm from a' to cut the b' locus, drop down to a's horizontal line and rotate to b's locus to obtain ab (71.94 mm), then project b up to b' locus to complete a'b' (69.28 mm).
Answer:

True inclination to HP theta = 25.94 degrees; Top View length = 71.94 mm; Front View length = 69.28 mm (with B at 50 mm above HP and 60 mm in front of VP).

Question 3

State the Right-Angle (Perpendicular Lines) Theorem in orthographic projection. Explain why two lines that are perpendicular in 3D space often do not measure 90 degrees in the Front or Top View, and describe how to construct a Point View (End View) of an oblique line AB.

Right-Angle Theorem: Two lines that are perpendicular in 3D space project at 90 degrees in an orthographic view if and only if at least one of the lines is parallel to that plane of projection (meaning it appears in True Length in that view), and neither line is perpendicular to the plane. If both lines are oblique to the projection plane, foreshortening distorts their projected angle away from 90 degrees.

Constructing a Point View of an oblique line AB:

  1. Draw primary folding line X1Y1 parallel to ab (in TV) or a'b' (in FV).
  2. Project A and B across X1Y1 using distances from XY in the adjacent view; the resulting line a1'b1' is in True Length.
  3. Draw secondary folding line X2Y2 perpendicular (90 degrees) to True Length a1'b1'.
  4. Project a1' and b1' along the direction of a1'b1' across X2Y2. Because X1Y1 was parallel to ab, A and B have equal distances to X1Y1 and therefore project to a single point a2(b2)—the Point View of AB.
Answer:

Perpendicular lines appear at 90 degrees in a view only when at least one line is shown in True Length in that view. A Point View of an oblique line requires two auxiliary views: View 1 parallel to one projection (giving True Length) followed by View 2 perpendicular to that True Length.

Question 4

Outline the Auxiliary View method to measure: (a) The true angle between two intersecting lines AB and BC; and (b) The true angle between a line PQ and an oblique plane ABC.

(a) True angle between intersecting lines AB and BC:

  1. Lines AB and BC form triangle ABC. Draw a horizontal line a'h' in FV (h' on b'c') and project to ah in TV to obtain a True-Length horizontal line in plane ABC.
  2. Draw X1Y1 perpendicular to ah to get the Edge View of triangle ABC (a1'b1'c1').
  3. Draw X2Y2 parallel to Edge View a1'b1'c1' to project the True Shape a2 b2 c2. The angle measured at a2–b2–c2 is the true angle.

(b) True angle between line PQ and oblique plane ABC:

  1. Project both plane ABC and line PQ through View 1 (X1Y1 perpendicular to horizontal line ah) to get Edge View a1'b1'c1' and p1'q1'.
  2. Project both through View 2 (X2Y2 parallel to a1'b1'c1') to get True Shape a2 b2 c2 and p2 q2.
  3. Draw a third folding line X3Y3 parallel to p2 q2 and project both plane ABC and line PQ into View 3. Because View 3 is perpendicular to the True-Shape view, ABC reverts to an Edge View (a3 b3 c3) while PQ appears in True Length (p3 q3). The acute angle between them is the exact line-to-plane angle.
Answer:

(a) Find the Edge View then True Shape of triangle ABC; measure angle a2–b2–c2 directly. (b) Carry line PQ through Edge View (View 1) and True Shape of ABC (View 2), then add View 3 with X3Y3 parallel to p2 q2 so ABC appears as an Edge View again while PQ appears in True Length; measure the acute angle directly.

Question 5

Differentiate between intersecting lines and skew lines in orthographic views. Explain the Point-View Method to determine both the shortest distance and the angle between two skew lines AB and CD (and verify for a concrete check where a skew separation vector projects to (10, -5, 10) along unit normal (1/3, 2/3, 2/3) that the perpendicular clearance equals 20/3 = 6.67 mm).

Intersecting vs. Skew lines in orthographic views:

  • Intersecting lines: The point where ab crosses cd in the Top View and the point where a'b' crosses c'd' in the Front View lie on the exact same vertical projector line perpendicular to XY.
  • Skew lines: Neither parallel in both views, nor do their apparent crossing points align on a single vertical projector.

Finding Shortest Distance and Angle between skew lines AB and CD:

  1. View 1 (X1Y1 parallel to ab): Project both lines; a1'b1' is in True Length.
  2. View 2 (X2Y2 perpendicular to a1'b1'): Project both lines; AB appears as a Point View a2(b2), and CD appears as c2 d2.
    • Shortest Distance: Drop a perpendicular from point a2(b2) onto c2 d2; its length is the exact shortest clearance (e.g., |(10)(1/3) + (-5)(2/3) + (10)(2/3)| = |10 - 10 + 20| / 3 = 6.67 mm).
  3. View 3 (X3Y3 parallel to c2 d2): Project both lines across X3Y3 using distances from X2Y2. Here c3'd3' is in True Length, and a3'b3' is also in True Length (since AB was a point view in View 2, making it parallel to X3Y3). The acute angle between a3'b3' and c3'd3' is the true angle between the skew lines.
Answer:

Intersecting lines have crossing points aligned on a common vertical projector; skew lines do not. Using View 1 parallel to AB (TL of AB) and View 2 perpendicular to TL (Point View of AB), the perpendicular from a2(b2) to c2 d2 gives the shortest distance (6.67 mm in the check). Adding View 3 parallel to c2 d2 puts both lines in True Length to read the skew angle directly.

← Geometrical ConstructionMulti View (Orthographic) Projections →