Machine Tools
Open in the Padhaiko app5.1 Lathes: Working principle, types of lathes, main parts of lathe, lathe operations
A lathe is the foundational machine tool of any mechanical workshop—often called the "mother of machine tools" because it generates cylindrical, flat, conical, and helical surfaces by rotating the workpiece against a rigidly held cutting tool.
Working Principle of a Lathe
The workpiece is gripped securely in a chuck or mounted between centers and rotated continuously about its longitudinal axis at a selected spindle speed (RPM). A hardened single-point cutting tool clamped in the tool post is pressed into the rotating work and fed:
- Longitudinally (parallel to the spindle axis) to produce cylindrical diameters (turning), or
- Transversely / Radially (perpendicular to the axis) to produce flat end faces (facing) or cut off stock (parting).
Lathe Speed, Machining Time, and Taper Formulas
- Cutting Speed (V, in m/min): V = (pi x D x N) / 1000 ==> Spindle Speed N = (1000 x V) / (pi x D) RPM where D = workpiece diameter (mm) and pi = 3.1416.
- Turning / Facing Time (T, in min): T = L_travel / (f x N) where L_travel = tool travel length (mm) and f = feed rate (mm/rev).
- Taper Turning Angles & Tailstock Set-Over:
- Compound-rest swivel half-angle (alpha): tan(alpha) = (D - d) / (2 x L_t)
- Tailstock set-over (S) for total job length L_job: S = L_job x (D - d) / (2 x L_t) where D = large taper diameter, d = small taper diameter, and L_t = length of taper.
Types of Lathes
- Speed Lathe: Simplest construction (headstock, tailstock, bed, hand tool rest; no carriage/leadscrew). High spindle speeds (1200–3600 RPM) used for woodturning, metal spinning, and polishing.
- Engine / Centre Lathe: Standard general-purpose metal-cutting workshop lathe equipped with an all-geared or cone-pulley headstock, carriage, feed rod, and leadscrew for turning and thread cutting.
- Bench Lathe: Compact precision engine lathe mounted on a workbench for small instrument and model parts.
- Tool Room Lathe: High-accuracy centre lathe with wide spindle-speed range, precision leadscrew, and taper/collet attachments for making gauges, dies, and tools.
- Capstan and Turret Lathes: Semi-automatic production lathes replacing the tailstock with a multi-station hexagonal turret holding pre-set tools for rapid repetitive batch manufacturing.
- Automatic & CNC Lathes: Computer-controlled (G-code/M-code) or cam-driven lathes performing complex multi-pass machining automatically.
Main Parts of a Centre Lathe
| Component | Location & Construction | Primary Function |
|---|---|---|
| Bed | Heavy cast-iron beam with precision-ground V-ways and flat ways | Forms the rigid backbone supporting headstock, carriage, and tailstock in alignment |
| Headstock | Mounted at left end; houses main hollow spindle, speed gearbox, and chuck | Drives and rotates the workpiece at selectable spindle speeds and transmits feed drive |
| Tailstock | Slides on bed ways at right end; has a handwheel-fed quill and Morse taper bore | Supports long shafts with a dead/revolving center; holds drills/reamers; offsets laterally for taper turning |
| Carriage (Saddle & Apron) | Moves along bed ways; carries cross-slide, compound rest, and tool post | Holds, positions, and feeds the cutting tool longitudinally (hand/power) and crosswise |
| Compound Rest | Swivel base graduated in degrees mounted on top of the cross-slide | Feeds the tool at any desired angle for short tapers and chamfers |
| Feed Rod & Leadscrew | Two parallel shafts along front of bed driven by feed gearbox | Feed rod drives normal longitudinal/cross power feeds; Leadscrew (Acme thread) engages split half-nuts strictly for precision thread cutting |
Lathe Operations (Syllabus List)
- Facing: Feeding the cutting tool radially inward (or outward) across the end of the workpiece to square the end face flat and bring the bar to exact length. Always set the tool tip exactly at spindle center height so no central pip remains.
- Centre Drilling: Mounting a short rigid combination drill and countersink in a tailstock drill chuck to cut a 60-degree conical seat at the shaft end, ready to support a tailstock revolving/dead center or guide a larger drill.
- Turning:
- Plain (Straight) Turning: Feeding the tool parallel to the axis to reduce diameter uniformly along the length.
- Step Turning: Cutting distinct concentric diameters separated by square shoulders.
- Taper Turning: Producing a uniform conical diameter change using the compound rest (short steep tapers), tailstock set-over (long shallow external tapers), taper turning attachment, or broad-nose form tool.
- Knurling: Pressing hardened patterned steel rollers (knurling tool) firmly against the rotating cylindrical work to cold-form (plastically emboss) diamond, straight, or diagonal ridges for non-slip hand grips (tool handles, micrometer thimbles). Knurling is a forming operation, not a metal-cutting operation, and requires slow speed and generous oil.
- Boring: Enlarging and truing an existing drilled or cored hole to an exact diameter using a single-point boring bar held in the tool post. Unlike reaming, boring corrects hole concentricity and alignment with the spindle axis.
- Chamfering: Beveling a sharp edge (commonly at 45 degrees) at the end of a shaft or shoulder to remove burrs, prevent cut fingers, and provide a lead-in for mating nuts or bearings.
- Thread Cutting: Synchronizing carriage travel with spindle rotation by closing the split half-nuts onto the rotating leadscrew, driven through change gears at the ratio: Gear Ratio (Driver / Driven) = Pitch of Work Thread / Pitch of Leadscrew. Multiple light passes are taken with a V-shaped threading tool ground to the exact thread angle (60 deg for ISO metric).
- Countersinking: Machining a conical bevel (60, 82, or 90 degrees) at the entrance of a drilled hole to seat flat-head countersunk screws flush or prepare center seats.
- Counterboring: Enlarging the upper section of a drilled hole to a larger flat-bottomed cylindrical recess (using a boring bar or piloted counterbore) so socket-head cap screw heads sit recessed below the surface.
5.2 Drilling Machine: Types of drilling machine, types of drill bits, drilling operations
A drilling machine (drill press) produces circular holes in stationary clamped workpieces by rotating a multi-point cutting tool (drill bit) and feeding it axially downward.
Types of Drilling Machines
| Machine Type | Key Construction Features | Typical Application |
|---|---|---|
| Portable Hand Drill | Compact electric or cordless pistol-grip motor with keyed/keyless chuck | Light site drilling, assembly repairs, sheet-metal holes (up to ~10–13 mm) |
| Sensitive (Bench) Drill | Small bench-mounted column, stepped V-belt pulleys, purely manual hand-lever feed | Small precision holes (up to ~12 mm) where the operator "feels" cutting resistance directly |
| Upright / Pillar Drill | Heavy floor-mounted column, geared/belt drive, power feed + manual feed, slotted elevating table | General workshop drilling of medium-to-large holes (up to ~50 mm) in heavy plates |
| Radial Drilling Machine | Large vertical column carrying a horizontal radial arm that swings and elevates, with a sliding drill head | Heavy, bulky castings and large structural frames where moving the workpiece under a fixed spindle is impractical |
| Gang Drilling Machine | Multiple independent vertical drill heads mounted side-by-side over one long worktable | Sequential mass production (e.g., Station 1 drill -> Station 2 counterbore -> Station 3 ream -> Station 4 tap) |
| Multi-Spindle Drill | Single drive head branching into several adjustable spindles driven simultaneously | Drilling an entire bolt-hole pattern (e.g., pipe flanges, engine blocks) in a single stroke |
Types of Drill Bits
- Flat (Spade) Drill: Forged flat blade with two ground cutting edges and no helical flutes; inexpensive for large rough holes or deep-hole gun setups, but chips clog easily.
- Straight-Fluted Drill: Two straight axial flutes (zero helix angle); prevents the drill from grabbing or pulling itself forward when drilling brass, bronze, or thin sheet metal.
- Twist Drill (Parallel Shank & Taper Shank): Standard workshop drill with two helical flutes forming two cutting lips, a 118-degree point angle (for mild steel), and a chisel edge at the web center. Parallel shanks (up to 13 mm) fit 3-jaw chucks; Morse taper shanks (larger sizes) lock directly into the spindle taper via a tang and are ejected with a drill drift.
- Center Drill (Combined Drill & Countersink): Short stubby double-ended bit producing a small pilot hole and a 60-degree conical seat in one pass.
- Core Drill (Three- or Four-Fluted): No center chisel edge; designed solely to enlarge existing cored/punched holes accurately without wandering.
Drilling Operations (Syllabus List)
- Drilling: Cutting a cylindrical hole from solid metal using a twist drill. Always center-punch the hole location first, clamp the job in a machine vice over a backing block, and ease feed pressure at breakthrough.
- Counterboring: Enlarging the top mouth of an existing hole concentrically to a larger cylindrical diameter with a square flat shoulder using a piloted counterbore (the solid pilot guides in the existing hole to keep both diameters concentric), hiding bolt or cap-screw heads flush below the surface.
- Reaming: Sizing and finishing a slightly undersized drilled hole to exact dimensional accuracy and smooth surface finish using a multi-flute machine reamer.
- Leave only 0.2 to 0.5 mm diameter allowance for reaming.
- Run the reamer at roughly half the drilling RPM, never rotate the reamer backward (reversing chips wedges and snaps teeth), and use generous cutting fluid.
- Tapping: Cutting internal screw threads in a pre-drilled tap drill hole using a machine tap held in a tapping attachment (with a reversing clutch and overload torque limiter) at very low spindle speed.
| Operation | Tool Used | Purpose | Typical Speed & Finish |
|---|---|---|---|
| Drilling | 2-flute Twist Drill | Originate a hole from solid stock | Full cutting speed; rough surface, slight oversize |
| Reaming | Multi-flute Reamer | Bring drilled hole to exact size & smooth finish (removes 0.2–0.5 mm) | ~50% of drilling RPM; high accuracy & smooth bore |
| Counterboring | Piloted Counterbore | Create flat-bottomed cylindrical recess for screw heads | ~50% of drilling RPM; stepped concentric pocket |
Worked Examples
1
A mild steel shaft of diameter D = 40 mm and total length L_job = 150 mm is machined on a centre lathe at a recommended cutting speed of V = 30 m/min and longitudinal feed f = 0.2 mm/rev: (a) Calculate the required spindle speed N (in RPM) and the machining time T for a single straight-turning pass over a length of 120 mm. (b) If a uniform taper from D = 40 mm down to d = 30 mm is to be turned over L_t = 75 mm of this 150 mm shaft using the tailstock set-over method, calculate the required tailstock offset S.
(a) Compute spindle speed (N) and single-pass turning time (T):
- Spindle speed: N = (1000 x V) / (pi x D) = (1000 x 30) / (3.1416 x 40) = 30000 / 125.664 = 238.7 RPM (select nearest available lathe gearbox speed, e.g. 240 RPM).
- Machining time: T = L_travel / (f x N) = 120 / (0.2 x 238.73) = 120 / 47.746 = 2.51 minutes (approx. 2 min 31 sec).
(b) Compute tailstock set-over (S) for the taper:
- S = L_job x (D - d) / (2 x L_t) = 150 x (40 - 30) / (2 x 75) = (150 x 10) / 150 = 10.0 mm (toward the front/cutting tool).
(a) Spindle speed N = 238.7 RPM (~240 RPM), turning time T = 2.51 min; (b) Tailstock set-over S = 10.0 mm.
2
(a) A 12 mm twist drill (point allowance approx. 0.3 x D) drills a through hole in a 24 mm thick cast-iron plate at a cutting speed V = 25 m/min and feed f = 0.15 mm/rev. Calculate the spindle speed N (RPM) and total drilling time T (in minutes and seconds). (b) A centre lathe has a 6 mm pitch leadscrew. Find the change-gear ratio (Driver / Driven) and suggest a standard pair of change gears to cut a 1.5 mm pitch metric thread.
(a) Calculate drilling RPM and total drilling time:
- Spindle speed: N = (1000 x V) / (pi x D) = (1000 x 25) / (3.1416 x 12) = 25000 / 37.699 = 663.1 RPM (choose nearest speed ~660 RPM).
- Total drill travel including conical point approach (0.3 x D): L_travel = Plate thickness + 0.3D = 24 + (0.3 x 12) = 24 + 3.6 = 27.6 mm.
- Drilling time: T = L_travel / (f x N) = 27.6 / (0.15 x 663.15) = 27.6 / 99.47 = 0.277 min = 0.277 x 60 = 16.6 seconds.
(b) Calculate lathe thread-cutting change-gear ratio:
- Gear Ratio = (Driver teeth) / (Driven teeth) = (Pitch of work thread) / (Pitch of leadscrew) = 1.5 / 6.0 = 1 / 4.
- Multiplying numerator and denominator by 20 gives a standard gear pair: Driver = 20 teeth, Driven = 80 teeth (or 25T driver / 100T driven).
(a) Drill RPM N = 663.1 RPM, drilling time T = 0.277 min (16.6 s); (b) Change-gear ratio = 1 : 4 (e.g., 20T driver on spindle, 80T driven on leadscrew).
3
Outline the ordered sequence of lathe operations required to produce a stepped, knurled mild steel handle from a 32 mm diameter x 110 mm long round bar:
- Front 40 mm length turned to 20 mm diameter with a 2 x 45 deg chamfer at the end,
- Remaining 55 mm grip length turned to 28 mm diameter and diamond knurled,
- A centre-drilled hole at the free end for tailstock support during turning.
Mount stock, face, and centre drill:
- Grip the 32 mm bar in a 3-jaw self-centering chuck with ~100 mm protruding (remove chuck key immediately!).
- Mount a right-hand facing tool at exact spindle center height and face the end flat to clean up.
- Clamp a combination centre drill in the tailstock drill chuck, lock the tailstock, and centre drill the end face (using slow feed and cutting oil) to form a 60-degree center seat; engage a revolving live center for rigid support.
Turn steps, chamfer, and knurl:
- Plain/Step Turn the full 95 mm working length down from 32 mm to 28 mm diameter in 1–2 roughing passes and one light finishing pass (check with vernier caliper).
- Step Turn the front 40 mm section down from 28 mm to 20 mm diameter, leaving a clean square shoulder at 40 mm.
- Swivel or angle a tool to chamfer the 20 mm nose 2 mm x 45 degrees (and lightly break the 28 mm edge).
- Set the lathe to a low spindle speed, mount a diamond knurling tool square to the work surface with heavy cross-slide pressure and generous cutting oil, and engage slow power feed across the 55 mm grip section to form crisp knurling ridges.
- Deburr sharp edges with a smooth file (keeping hands clear of rotating chuck jaws), switch off, wait for full stop, and part/cut off to overall length.
- Chuck stock & face end flat -> 2. Centre drill & support with tailstock center -> 3. Plain turn to 28 mm -> 4. Step turn front 40 mm to 20 mm -> 5. Chamfer nose 2 x 45 deg -> 6. Diamond knurl 55 mm section at low speed with heavy pressure and oil -> 7. Deburr and part off.
Exercises
added
A steel shaft of diameter D = 50 mm and total length 180 mm is turned on a centre lathe at cutting speed V = 35 m/min and feed f = 0.25 mm/rev. (a) Calculate the spindle speed N (RPM) and the machining time for one pass over a length of 160 mm. (b) Compute the tailstock set-over (S) needed to turn a taper from 50 mm down to 38 mm over a taper length of 90 mm.
(a) Spindle speed and turning time:
- Spindle speed: N = (1000 x V) / (pi x D) = (1000 x 35) / (3.1416 x 50) = 35000 / 157.08 = 222.8 RPM.
- Turning time: T = L_travel / (f x N) = 160 / (0.25 x 222.82) = 160 / 55.705 = 2.87 minutes.
(b) Tailstock set-over:
- S = L_job x (D - d) / (2 x L_t) = 180 x (50 - 38) / (2 x 90) = (180 x 12) / 180 = 12.0 mm.
(a) N = 222.8 RPM, machining time = 2.87 min; (b) Tailstock set-over S = 12.0 mm.
(a) A 10 mm HSS twist drill (point approach allowance = 0.3D) drills a through hole in a 30 mm thick mild steel block at cutting speed V = 22 m/min and feed f = 0.12 mm/rev. Find the drill spindle speed N (RPM) and drilling time T (in seconds). (b) A lathe has an 8 mm pitch leadscrew. Find the change-gear ratio (Driver / Driven) required to cut an external thread of 2.0 mm pitch.
(a) Drilling RPM and drilling time:
- N = (1000 x 22) / (3.1416 x 10) = 22000 / 31.416 = 700.3 RPM.
- Total travel = 30 + (0.3 x 10) = 30 + 3 = 33 mm.
- T = 33 / (0.12 x 700.28) = 33 / 84.03 = 0.393 min = 0.393 x 60 = 23.6 seconds.
(b) Thread-cutting gear ratio:
- Driver / Driven = Pitch_work / Pitch_leadscrew = 2.0 / 8.0 = 1 / 4 (for example, 25T driver / 100T driven).
(a) N = 700.3 RPM, drilling time = 23.6 seconds (0.393 min); (b) Gear ratio = 1 : 4 (e.g. 25T driver / 100T driven).
List the six main structural parts of a centre lathe and explain the specific difference in function between the feed rod and the leadscrew, as well as between the cross-slide and the compound rest.
Main parts of a centre lathe:
- Bed: Rigid cast-iron base with precision guideways aligning all assemblies.
- Headstock: Left-end housing containing spindle, speed gears, and work-holding chuck.
- Tailstock: Right-end sliding support holding centers for long shafts and drills/reamers.
- Carriage: Saddle and apron assembly carrying and feeding the cutting tool along the bed.
- Cross-slide & Compound Rest: Transverse and angular tool-feeding slides mounted on the saddle.
- Feed Rod & Leadscrew: Drive shafts transmitting rotary power to move the carriage automatically.
Key functional distinctions:
- Feed rod vs. Leadscrew: The feed rod powers routine longitudinal turning and cross-facing feeds via clutch gears in the apron, whereas the precision Acme-threaded leadscrew engages the split half-nuts strictly during thread cutting so tool advance locks synchronously to spindle revolutions without slip.
- Cross-slide vs. Compound rest: The cross-slide moves strictly perpendicular (90 deg) to the spindle axis for facing and depth of cut; the compound rest sits on top of the cross-slide on a graduated swivel base so it can be angled to turn short tapers, chamfers, and angled thread infeeds.
Main parts: bed, headstock, tailstock, carriage, cross-slide/compound rest, feed rod/leadscrew. The feed rod drives regular power feeds while the leadscrew drives synchronized thread cutting; the cross-slide feeds strictly perpendicular to the spindle while the compound rest swivels to feed at any set angle.
Define and distinguish the following lathe operations: (a) Facing vs. Turning, (b) Boring vs. Drilling, (c) Knurling, and (d) Countersinking vs. Counterboring.
Explain each pair and operation clearly:
- (a) Facing vs. Turning: Facing feeds the tool radially across the end face (perpendicular to axis) to flatten the end and set length; turning feeds the tool parallel to the axis to reduce external diameter.
- (b) Boring vs. Drilling: Drilling creates a hole from solid material using a multi-flute twist drill (following any pre-punched wobble); boring enlarges an existing hole using a rigid single-point boring bar to produce true concentricity and exact size.
- (c) Knurling: Cold plastic embossing (not chip cutting) using hardened patterned rollers pressed onto a rotating shaft to form diamond or straight non-slip grip ridges.
- (d) Countersinking vs. Counterboring: Countersinking cuts a conical bevel at the mouth of a hole for flat-head conical screws; counterboring enlarges the top of a hole cylindrically with a flat square shoulder to recess socket-head cap screws.
Facing (flat end, radial feed) vs. Turning (cylindrical OD, axial feed); Drilling (originate hole) vs. Boring (enlarge/true existing hole with single-point bar); Knurling (cold-forming grip pattern with rollers); Countersinking (conical bevel) vs. Counterboring (flat-bottomed cylindrical recess).
Compare a sensitive bench drilling machine, a pillar (upright) drilling machine, and a radial drilling machine in terms of capacity and applications. Also state two essential rules when performing reaming on a drilling machine.
Compare the three drilling machines:
- Sensitive Bench Drill: Compact belt-driven machine with purely manual hand-lever feed (no power feed); used for small holes (up to ~12 mm) where the operator feels drill pressure to avoid snapping small bits.
- Pillar (Upright) Drill: Heavy floor-standing column with geared drive and power feed; drills medium-to-large holes (up to ~50 mm) in heavy plates clamped to an elevating table.
- Radial Drilling Machine: Heavy column with a swinging, elevating radial arm carrying a movable drill head; allows drilling multiple holes across massive, heavy castings without moving the workpiece.
Two essential rules for machine reaming:
- Leave only 0.2 to 0.5 mm stock in the drilled hole (too much stock overloads the reamer; too little causes rubbing/glazing).
- Run at roughly half the drilling spindle speed with generous cutting fluid, and never rotate a reamer backward (even while withdrawing) or chips will jam and chip the cutting flutes.
Sensitive drill (small holes <= 12 mm, hand feel), pillar drill (heavy floor machine, power feed up to ~50 mm), radial drill (swinging arm moves spindle over large heavy castings). For reaming: leave 0.2–0.5 mm allowance, run at ~50% drilling RPM with coolant, and never turn the reamer backward.