Acoustics
Open in the Padhaiko app2.1 Introduction
Acoustics is the branch of physics concerned with the generation, propagation, reception, and architectural control of mechanical sound waves. In engineering, architectural acoustics ensures clear speech and rich music inside halls, auditoriums, and classrooms without echoes or excessive noise.
2.1.1 Threshold of hearing and loudness
Sound intensity is the acoustic power passing perpendicularly through unit cross-sectional area (). Because the human ear responds roughly logarithmically across an enormous dynamic range ( to ), loudness is measured on a logarithmic decibel scale.
Threshold of Hearing, Weber–Fechner Law, and Intensity Level
- Threshold of Hearing (): The minimum sound intensity audible to an average healthy human ear at a standard reference frequency of :
- Threshold of Pain: Approximately ().
- Loudness () and Weber–Fechner Law: Loudness is the physiological sensation of sound strength perceived by the ear. According to the Weber–Fechner law, loudness is proportional to the logarithm of the physical stimulus intensity:
- Sound Intensity Level (): Defined in decibels () as:
A -fold increase in intensity corresponds to a rise; doubling the intensity adds .
2.1.2 Reverberation and reverberation time
When a sound source inside an enclosed hall stops emitting, the sound does not vanish instantaneously. Sound waves undergo hundreds of reflections from walls, ceiling, floor, and furniture before their energy is absorbed.
Reverberation and Reverberation Time
- Reverberation: The persistence of audible sound in an enclosure after the original source has been switched off, caused by multiple reflections from bounding surfaces.
- Reverberation Time ( or ): The time interval required for the average acoustic energy density (or sound intensity) in an enclosure to decay to ( millionth) of its steady-state value, corresponding to a drop of in intensity level after the source stops:
2.1.3 Absorption coefficient
When a sound wave strikes a surface, part of its energy is reflected and the rest is absorbed (transmitted or dissipated as heat inside porous fibers).
Sound Absorption Coefficient and Total Absorption
The absorption coefficient of a material at a given frequency is the ratio of sound energy absorbed by the surface to the total sound energy incident upon it:
An open window absorbs all incident sound (none returns), serving as the unit standard with . The total absorption (in -sabins or , open-window units) of a hall with surface areas and absorption coefficients is:
where is the total interior surface area and is the mean absorption coefficient.
| Surface / Material | Absorption Coefficient () | Acoustic Role |
|---|---|---|
| Open window (standard reference) | Complete absorption | |
| Acoustic mineral wool / heavy drapes | High absorption; reduces echo and reverberation | |
| Carpet on concrete floor | Moderate-to-high floor damping | |
| Upholstered / occupied audience seat | Stabilizes hall acoustics regardless of occupancy | |
| Wood paneling / plaster on lath | Low absorption; helps early sound reinforcement | |
| Painted brick, concrete, marble, glass | Strong reflector; excessive area causes harsh glare |
2.1.4 Sabine's law
Through systematic experiments in lecture halls at Harvard University, Wallace Clement Sabine established that reverberation time is directly proportional to room volume and inversely proportional to total sound absorption .
Sabine's Formula for Reverberation Time
For an enclosure of interior volume (in ) and total absorption (in ), assuming a diffuse sound field with speed of sound in air, the reverberation time (in seconds) is:
(Note: Some textbooks use or depending on the assumed room temperature and speed of sound; at .)
For halls with high absorption (), Eyring's formula refines Sabine's equation by replacing with :
2.1.5 Conditions for good acoustics
Designing an auditorium or lecture hall for clear, comfortable listening requires balancing several acoustic criteria:
- Optimum Reverberation Time: Neither too short ("dead" hall, weak sound) nor too long (overlapping syllables, muddy speech). Typical targets: for lecture/speech halls, for concert music halls.
- Sufficient Loudness: Every listener—including the back row—must receive adequate direct and early reflected sound energy; a parabolic/splayed ceiling reflector behind the stage boosts projection toward the rear.
- Absence of Echoes: Distinct reflected arrivals delayed by more than (path difference ) are heard as separate echoes. High rear walls and distant parallel walls should be covered with absorbent material or broken with diffusers.
- No Sound Focusing or Dead Spots: Concave domes, cylindrical ceilings, or curved rear walls focus sound rays into loud hotspots while leaving nearby zones acoustically "dead." Flat or convex splayed surfaces scatter sound evenly.
- No Resonance / Standing Waves: Parallel rigid walls with simple rational dimension ratios can excite room eigenmodes at low frequencies; non-parallel walls and varied geometry prevent coloration.
- External Noise Isolation (Echelon Effect): Use double-glazed windows, heavy acoustic doors, vibration-isolated HVAC ducts, and avoid uniformly spaced stepped seats that produce pitched "echelon" reflections.
2.1
An auditorium has a volume of . Its interior surfaces consist of of plaster (), of concrete (), and of acoustic tile (). Inside are upholstered seats, each contributing of absorption. Calculate the reverberation time using Sabine's formula.
Total absorption :
Sabine's reverberation time:
The reverberation time of the auditorium is .
2.2 Ultrasound
Human hearing spans roughly to . Acoustic waves with frequencies above are called ultrasonic waves (or ultrasound). Because their wavelengths in liquids and solids are very short ( or sub-), ultrasonic beams travel along sharp, weakly diffracting paths and carry high energy density.
2.2.1 Production (Piezoelectric) of ultrasound and its applications
Piezoelectric Effect and Ultrasonic Oscillator
- Direct Piezoelectric Effect: When mechanical pressure or tension is applied across opposite faces of an asymmetric crystal (such as quartz, Rochelle salt, or barium titanate), equal and opposite electric charges appear on the perpendicular faces.
- Inverse Piezoelectric Effect: When an alternating electric voltage is applied across the faces of a piezoelectric crystal, the crystal undergoes periodic mechanical expansion and contraction at the same frequency.
- Resonant Ultrasonic Production: If the frequency of the high-frequency AC oscillator matches the natural mechanical vibration frequency of the crystal plate of thickness , density , and Young's modulus , resonance occurs with maximum ultrasonic output:
For the fundamental mode (), .
Major Engineering Applications of Ultrasound:
- SONAR (Sound Navigation and Ranging): Measuring ocean depth () and locating submarines, shoals of fish, or submerged obstacles.
- Ultrasonic Cleaning: Cavitation bubbles generated in liquid baths dislodge grease and oxide films from intricate watch parts, silicon wafers, and surgical instruments.
- Ultrasonic Welding and Machining: Local high-frequency friction welds plastics and thin metals without external solder; abrasive slurry drills hard, brittle materials like glass or ceramics.
- Emulsification & Homogenization: Mixing immiscible liquids (oil and water, photographic emulsions).
2.2.2 Test of structure and materials
In Non-Destructive Testing (NDT), ultrasonic waves inspect internal defects (cracks, voids, blowholes, delaminations) and measure wall thickness in castings, welds, rails, and pressure vessels without damaging the component.
- Pulse-Echo Method: A piezoelectric transducer emits short ultrasonic pulses into the test specimen using a thin couplant gel (to eliminate air gaps that would reflect nearly of the wave).
- Wave Reflection at Acoustic Impedance Mismatches: Whenever a pulse hits an internal flaw (metal-to-air boundary) or the back wall, part of the energy reflects back to the transducer and appears as an intermediate echo on an oscilloscope/A-scan display.
- Depth and Thickness Calculation: If the longitudinal wave speed in the material is , and echoes return at round-trip time (flaw) and (back wall):
- Through-Transmission Method: Separate transmitter and receiver transducers sit on opposite sides; an internal defect blocks or attenuates the transmitted beam, casting an acoustic "shadow."
2.2.3 Medical uses
Ultrasound is non-ionizing (far safer than X-rays for soft tissue and fetal imaging) and widely used in both diagnostics and therapy:
- Diagnostic Sonography (B-mode Imaging): Pulses at map organ boundaries, fetal growth, gallstones, and abdominal structures from echo amplitudes and arrival times.
- Doppler Ultrasound (Echocardiography & Vascular Flow): Frequency shifts () in echoes reflected from moving red blood cells measure blood flow velocity, valve function, and fetal heartbeat.
- Therapeutic Applications:
- Physiotherapy: Controlled deep-tissue heating relieves muscle spasms and joint stiffness.
- Lithotripsy / Focused Ultrasound: High-intensity focused ultrasound (HIFU) shatters kidney stones non-invasively or ablates localized tumors.
- Dentistry & Neurosurgery: Ultrasonic scalers remove dental tartar cleanly; ultrasonic aspirators emulsify delicate brain tumors while sparing nearby vessels.
2.2
A quartz crystal plate of thickness is used in a piezoelectric ultrasonic generator. Given Young's modulus and density for quartz, calculate the fundamental resonant frequency of the ultrasonic waves produced.
Convert thickness to SI units:
Apply the fundamental crystal resonance formula ():
The fundamental ultrasonic frequency produced is .
2.3
During ultrasonic pulse-echo testing of a steel plate (speed of longitudinal sound waves ), a defect echo is detected at and the back-wall echo returns at . Calculate:
- The depth of the internal defect from the scanning surface.
- The total thickness of the steel plate.
Depth of the internal defect: Because the pulse travels to the defect and back in time :
Total plate thickness:
- Defect depth:
- Total plate thickness:
Exercises
Practice Exercises — Architectural Acoustics and Ultrasound
Define threshold of hearing, sound intensity level, reverberation, and reverberation time. State Sabine's law and explain five essential conditions for good acoustics in a large auditorium.
Key acoustic definitions:
- Threshold of hearing (): The faintest sound intensity perceptible to the average human ear.
- Sound intensity level: .
- Reverberation & Reverberation time (): Persistence of sound via repeated reflections after the source stops; is the time taken for sound intensity to decay to of its initial value (a drop).
- Sabine's law: , where is hall volume () and is total sound absorption ().
Five conditions for good auditorium acoustics:
- Optimum reverberation time ( for speech; for music).
- Adequate loudness throughout the hall using splayed reflective surfaces near the stage.
- Elimination of echoes (path differences ) using rear-wall absorption and diffusers.
- Avoidance of curved/concave focusing surfaces that create hotspots and dead zones.
- Isolation from external traffic/HVAC noise and avoidance of parallel-wall resonances.
Threshold of hearing is ; intensity level is ; reverberation time is the time for a decay. Good acoustics requires optimum , uniform loudness, no echoes, no sound focusing, and strong noise isolation.
- A concert speaker produces a sound intensity level of . Find its physical sound intensity in ().
- A single machine produces a noise level of at a workstation. What will the total intensity level be when identical uncorrelated machines run simultaneously?
Part 1 — Intensity from decibel level:
Part 2 — Five identical machines: For uncorrelated sources of equal intensity , total intensity is :
- Total intensity level: ()
A hall of volume currently has a reverberation time of . To improve speech clarity, the reverberation time must be reduced to by laying carpet () over part of the bare concrete floor (). What area of carpet must be installed?
Initial and target total absorption: From Sabine's formula :
Required carpet area : Replacing an area of concrete () with carpet () increases total absorption by :
An area of of carpet must be installed.
Explain the piezoelectric effect and describe how ultrasonic waves are produced using a piezoelectric quartz oscillator. Distinguish between non-destructive material testing and medical diagnostic uses of ultrasound.
Piezoelectric effect and ultrasonic generation: When an asymmetric crystal like quartz experiences mechanical stress, electric charges appear across perpendicular faces (direct effect); conversely, applying an alternating voltage makes the crystal vibrate mechanically (inverse effect). Placing a thin quartz plate between metal electrodes driven by a high-frequency AC oscillator tuned to excites resonant thickness vibrations, radiating intense ultrasonic waves into the surrounding medium.
Material testing (NDT) vs. Medical diagnostics:
- Structure & Materials (NDT): High-power pulses () detect internal cracks, porosity, weld flaws, and wall thickness in metals, concrete, and composites via pulse-echo reflection times ().
- Medical Diagnostics & Therapy: Non-ionizing B-mode imaging maps soft tissues and fetal development; Doppler ultrasound measures blood flow velocity; focused ultrasound performs physiotherapy heating and kidney-stone lithotripsy.
A piezoelectric oscillator uses the inverse piezoelectric effect in a quartz plate driven at its resonant frequency to generate ultrasound. In NDT it locates internal cracks and measures thickness in engineering components; in medicine it provides safe soft-tissue imaging, Doppler blood-flow monitoring, and focused therapeutic treatments.
A quartz crystal has Young's modulus and density .
- Calculate the fundamental frequency of a quartz plate of thickness .
- What thickness of quartz plate is required to generate ultrasonic waves in its fundamental mode?
Acoustic wave speed in quartz:
Part 1 — Fundamental frequency for :
Part 2 — Thickness required for :
- Fundamental frequency: ()
- Required thickness for :